Ten advantages of LED high bay light 

   Ten advantages of LED high bay light 

1,chip of LED high bay light is very small, very fine chip encapsulated in transparent epoxy resin inside, so it is very small grain , very light , in the production and application can save a lot of material and space.

2, Rugged and durable

LED chips are completely encapsulated in epoxy . Compact epoxy resin particles is extremely difficult smashes , the entire light body and no loose parts ; inside the chip is extremely difficult to break , and very few thermal effects which may volatilize blown. These features make the LED difficult to damage. Compared with ordinary light bulbs, fluorescent lamps , LED can be described as impregnable, countless times rugged , durable countless times .

3, long life

In the right current and voltage , LED life of up to 100,000 hours , that theoretically the product life of more than 10 years , is the only long-lived star lighting fields.

4,Low voltage safety

LED using low voltage DC power supply ( can be rectified AC to DC ) , power supply voltage between 6 ~ 24V, because different products vary . In short it is more secure than application of high voltage DC power supply , especially for homes and public places.

5,Wide range of applications

Because small, small piece of each LED unit is 3 ~ 5mm square or round , so more suitable for the preparation of molding process complex devices . For example, the manufacture of soft , flexible tubes , lights , shaped snuff , is currently the only LED fit.

6,richer colors

Before lighting color is very simple, in order to achieve the purpose of color , one paint brush or the surface of the light colored cover sheet , the second is filled with inert gas glow in the lighting , so the richness of colors is limited . LED digital control , LED chips currently able to issue a variety of colors , including red , green, blue three primary colors , precisely because of this ternary color , controlled by the system , you can restore the colorful worlds .

7, less heat dissipation

LED high bay light cold light source is more advanced , unlike incandescent, fluorescent , as a large number of infrared and ultraviolet radiation , especially for lighting artifacts, jewelry, luxury cosmetics and other valuables. Almost no thermal effect of current incandescent like that, but not affected by thermal expansion and contraction of the bubble fried . Will not make the bulb yellow, will not make lamps accelerated aging , does not constitute the greenhouse effect on the surrounding environment.

8,less environmental pollution

LED for the protective effect of the environment mainly in three aspects:

First, there is no harm to metal mercury . LED high bay lights inside unlike fluorescent lamps that use highly hazardous mercury , does not appear likely to leak mercury ions , like fluorescent light bulbs after a public hazard events or damaged during the manufacturing process .

Second, the manufacture of epoxy resins are organic polymers LED , after curing with good physical and chemical properties of the wafer , high metal adhesion strength , hard and flexible, and most of the saline solvent stable, not easily damaged even after aging can be damaged or recycling , environmental pollution is not formed .

Third, LED lamps and light particles display layout , are generally produced by scattering , rarely produce light pollution.

9,more cost savings

Compared to incandescent lamps, fluorescent lamps , LED high bay light purchase price should be higher. However , due to the extremely low power consumption LED 's , in the long run can save a lot of electricity, you can save lamp replacement investment, and thus the cost of the integrated use of more cost-effective .

10,very low energy consumption

LED 's operating voltage is generally only 2 ~ 3.6V, operating current as long as 0.02 ~ 0.03A ie : electricity it consumes less than 0.1W, reducing energy consumption than the equivalent incandescent light efficiency more than 90 %, compared with energy-saving lamps reduced by more than 70%. Therefore, only the LED can be a real energy source !

To be  lighting industry bestowed favor on newly - led high bay light

Energy consumption within the plant , and also in terms of lighting applications accounted for a certain proportion, if say , a company's production plant covers an area of 300,000 square meters , it is estimated to count , in order to work properly and lighting , the use of the power of 3000kw, so the factory how to select energy saving lighting has become most people pay attention to a problem .

With the development of society, the lighting industry is now in the stage of rapid development, the emergence of a new type of energy saving lamps in the sales market - LED high bay light , its greatest feature is energy saving, addition addition , it has a long life, fast response characteristics also make it by people in hot pursuit.

LED high bay light due to its high quality features and appearance , at just listed by the people like and buy. LED high bay light in many aspects and fields are applied. It is the choice of using the light from abroad high brightness chip , is a high power LED (60W - 160W) new light . This material as a light source , more efficient heat conduction , light decay, pure light color , light irradiation uniformity, no ghosting , the human eye has a very good protection . People working in this reading light , substantially no eye fatigue. Therefore, in some families in the study often applied LED high bay light, as well as in some companies , the local office also applied. And LED High Bay Light is an environmentally friendly energy saving lamps , lighting tools than the average consumption of electricity in the lower 30 percent.

In many of the show , factories, operating room lighting can be applied to its soft, uniform light emitted , people will not feel eye fatigue LED mining light shines in the range , so that , LED high bay light is best suited for large, medium and small factories to use .

problem of led street light  in the application 

In the global energy crisis and environmental pressures increasingly prominent situation, LED light source used in road lighting has become a hot spot in recent years, the semiconductor lighting industry. LED device products applied to the lights, there are no special requirements for technology,What is advantagesand weakness of LED street lights compared to traditional high pressure sodium street lights currently ? how to solve a series of problems that we are worthy of serious study. 

1, the basic product standardization and commonality of large-scale use 

Currently launched LED street lights, product appearance, dimensions LED light-emitting particles arranged manner and quantity, the rectifier circuit and a variety of interior design. Such as: the number of single-tube power varies, ranging from 1 to 5 watts; different light distribution, there are bat-shaped, rectangular, Butterfly type, etc.; optical approach has its own free secondary optical lens and a second optical processing processing; driver situation has dedicated driver IC chip and no electrolytic capacitors; package multiple chip package and Billing Division situations chip packaging; technical line conditions have mold, the group of high-power, high-power chip, power and other dot-matrix . Power also has its own assembly and integration of two external power, cooling technology is different, which gave the popularity of running and maintenance after use has caused great inconvenience, does not conform to municipal utilities standardized, universal design principles. 

We believe that in the future the development process, the manufacturer should be strictly in accordance with national standard to ensure product safety and electrical equipment safe and reliable performance. Meanwhile, the city has been applied in the field of LED lighting products, the product must be standard, offers the following guarantee unity. 

Such as: For the same between the different stages of development of enterprise products, to ensure the standard of the main electrical components, unity, to avoid causing product replacement spare parts dating; between different enterprises for products, lighting body, emitting particle board The main electrical components, rectifier circuits should be based on national standards, to achieve the necessary standards and unity. 

2, the corresponding national standards to protect the healthy development of LED street light market 

Optical and thermal characteristics of LED and traditional light sources varies greatly, so that the existing LED measurement methods of measurement can not be fully applied to traditional lighting source. LED current in terms of product specifications or measurements were lack of proper standards, product variety, no standard measure, the market is not standardized, and the diversity of products has also led to large-scale production enterprises can not concentrate. The development of relevant standards has become an urgent demand for LED industry. At present, the National Standardization Technical Committee and other lighting appliances in the submittal phase, expected to be successively promulgated "LED general lighting made with national standards and industry standards." Companies should make a new market positioning and product planning, seize new opportunities, to invest the necessary quality assurance measures.

led high bay light choose high quality drive power 

1. Why led high bay light  need a high quality drive power ?

Since the LED does not contain toxic substances, environmental protection, long life, high efficiency photovoltaic many advantages , LED chip design and production and manufacturing processes have been quite mature , damaged the entire LED lighting system LED driver is mainly damage ; LED drive power due to the low quality of protection is not perfect, great damage will become low precision constant current LED chip current fluctuations ; therefore LED drive power LED lighting is the key , it is like a person's heart , to manufacture high -quality , LED lamps for lighting must use high -quality LED power driver to be able to meet the harsh working environment LED lighting systems and high maintenance cost requirements .

2.where the root of LED high bay light driver quality problems?

 A non-professional power supply design and manufacturing company ( requirements are too loose , too small ) ;

The second is not in accordance with the harsh working environment LED lighting design

a) -35 degrees to 70 degrees ambient temperature

b) waterproof design is not in place

c) mine design is not in place

3 How to ensure the LED high bay light driver quality and reliability ?

1 ) Professional design specification process control technology pre-research , feasibility assessment, preliminary design , detailed design , engineering, prototype and small batch trial production.

2 ) a reasonable margin component design

3 ) selection of high- quality components electrolytic capacitors , IC, power semiconductor , magnetic components.

4 ) strict quality verification and testing procedures

Stress analysis , EVT, SVT, DVT , such as testing and MTBF calculations and experimental verification.

4.  Why do we need efficient led high bay light drive power ?

1)High efficiency LED lighting systems overall energy requirements, low temperature rise , long life, high reliability and guaranteed basis . 1 ) High efficiency, low loss , low temperature rise like a console output 100W LED drive power , when efficiency up to 95 %, the loss is 5.2W, when the efficiency is only 85% , the loss of 17.6W, the latter is 3.4 times , experiments show that under the same conditions the former than the latter low temperature 10 ~ 15 ℃.

2 ) reduce the operating temperature of the LED light failure LED chip and delaying temperature rises will lead to changes in the electro-optical conversion efficiency of light-emitting device performance decay , even when serious failure , experimental tests show : LED temperature increase of 5 degrees Celsius itself , flux dropped 3%.

3 ) High efficiency, low temperature rise , long life if the choice of 105 degrees , life expectancy of 10,000 hours of high-temperature electrolytic capacitors, electrolytic capacitor life according to the prevailing estimate of the company , " each 10 degrees , doubling the life ," then it is at 95 degrees ambient the working life of 20,000 hours at 85 degrees ambient operating life of 40,000 hours , as Ron platinum drive power in general operating temperature of up to 70 degrees, the temperature of the electrolytic capacitor is substantially controlled at about 85 degrees , then the life expectancy of up to 40,000 hours , such as by working 12 hours a day total , the life expectancy in recent decades.

 4 ) High efficiency, low temperature rise , high reliability

 With the reduced supply temperature , IC, improving power semiconductors work environment , MTBF ( mean time between failures ) will significantly improve .

 5 )What is the PF? What is the PFC? Why should high- PF?

Power Factor PF is the abbreviation refers to the power factor, active power and apparent power ratio ; PFC Power Factor Corrector is the acronym refers to the power factor correction .

Revolution of LED High Bay Light

Revolution of led high bay light , sounds very distant thing, but with the development of LED production technology , LED high bay light is bound to be a big change. However, there are certain factors LED high bay light restricted its development . First, the reliability of the LED high bay light products , cost and other issues ; Secondly, although in 2012 the global LED high bay light market is estimated at approximately $ 4.48 billion , but the country lacks competitive products , the lack of a number of patents, and international companies can not compete ; in addition, the end of the study to be used if the general lighting system equipment, higher brightness while generating heat phenomenon will follow , and the lack of testing and certification technology , the core problem is to choose , such as eutectic materials.

Major LED high bay light manufacturers continue to improve in the upstream technology, in order to maintain the brightness of the finished packaged in this technological innovation management tools, we can more clearly grasp the next 3-5 years, mainstream LED high bay light lighting industry , there are two main programs , namely the rational allocation of resources for innovation , to master the most optimal process parameters , becoming the LED high bay light LED Industrial technology Development bigger and stronger lighting industry provides a guide to action .

According to follow-up study of Chinese LED high bay light market , affected by the global financial crisis, the number of orders due to reduced growth is slowing down dramatically . On the other hand , due to the tight schedule export tasks , resulting in the growth rate is slowing down . Research type of equipment to complete production prototype commercial or LED high bay light backlight products , are rushing their territory, compiled working groups. Faced with this situation at home and abroad , TEK Lighting LED high bay light is based on its own , with quality as the core , high quality Bridgelux chip , the life of 50,000 hours ; on the other hand , faced a tight schedule , TEK Lighting is strictly comply with the delivery, the customer base and establish a good image.

LED lighting market to benefit not only the mining lamps and other lighting equipment , as well as domestic electronic information industry to take this opportunity to, have to develop , is designed to effectively phase out traditional lighting . Although , LED high bay light development by certain restrictions now, but the growth of market demand will drive its development.

The issues of LED street lamp power supply design need attention

1, why LED street lamp power supply must constant ?

LED lighting characteristics determine the material influenced by the environment , such as elevated temperature , LED current increases , the voltage increases , the LED current will increase. Long-term than the rated current work , will greatly shorten the life of the LED lamp beads . The LED is constant when changing environmental factors such as temperature and voltage , to ensure that the operating current value unchanged.

2, LED street lamp power supply current precision

Precision constant current power supply on the market and some of the poor, as the popularity of the program recommended programs constant , error of ± 8%, constant error is too large . General requirements ± 3% on it. 3% of the design. To fine-tune the production of power in order to achieve ± 3% error .

3, voltage of the power supply of led street light operating

General LED 's recommended operating voltage is 3.0-3.5V, tested, most of the work in 3.2V, 3.2V calculated according to the formula so reasonable . N- series lamp beads total voltage = 3.2 * N

4, how much working current of LED street lamp power supply is the most appropriate ?

For example LED rated current 350 mA , and some plants used to make the outset , design 350 mA , in fact, this current work under very severe fever , after numerous comparison test , designed to be 320 mA is ideal . Minimize the amount of heat , so that more energy can become visible .

5, efficiency of LED street lamp power supply 

Subtracting the output power of the input power , this parameter is particularly important, the lower the value the greater the efficiency , it means that the input power is converted to heat a large part comes out ; if the lamp is mounted in a high temperature is generated , coupled with a light efficiency of our LED emitted than the heat, it will produce a higher temperature superposition , while we supply all the electronic components inside the life will increase with temperature and shortened so that the power efficiency is to determine the most life fundamental factor, efficiency is not too low, or the power consumption of too much heat . Non-Isolated efficient than isolated , generally more than 80% can, however , about the efficiency and light board matching connection

6, LED street lamp power supply cooling

The main factor is the cooling solution power LED lights beads in hot conditions , but can greatly extend the life , usually with aluminum and easier to heat . That is the power LED lights beads attached to the aluminum plate, external to maximize heat dissipation area .

Faced with such a vast LED market is really full of vigor , mainly to develop science can achieve a leading position on a few technical areas, I believe that China's LED business will become more powerful .

The analysis of LED high bay light price influence factors 

LED high bay light price influence factors : Most of the factories in energy saving renovation , an issue of great concern about price of LED high bay light , almost more than 70% of customer that consulting led high bay light price will be the first time think the price is really expensive . However , compare with effect of energy saving , the sum of the initial investment is not really a concern too , the following is an analysis under the influence of LED high bay light prices of several key factors.

1 , heat sink enclosure , a well designed , with plenty of material of LED high bay light heat sink enclosure , in time for the heat LED chips, avoid because of led high bay light prolonged work at high temperatures so that premature aging, there are some manufacturers to save costs , the big issue on the heat sink , such as sizes made look like high-end products , but actually enclosure significantly thinner in thickness , or directly cut short length of the back end of heat sink in order to achieve the purpose of saving materials , thus greatly reducing the price of LED high bay light , the result of customers buy the consequences can be imagined , it may be no big problem within six months or a year , but after a year , because this type of radiator due to dust , heat aging, resulting in significantly reduced performance , direct result of led chip will the rapid aging or burned out.

2 , LED chip , the age of domestic of led chip in everywhere, the quality of led chip is different , a good quality of LED chip can bring plenty of light lumens , and cooling effect of chip is also better than bad, higher packaging technology that allows the chip to maintain long-term work in a vacuum environment, substantially reduce the rate of aging . But some manufacturers in order to reduce led high bay light price , they uses LED chip with a workshop package , this chip wattage power not energy and packaging material have impurities, prone to deterioration at high temperatures , the result is that in addition to  LED high bay light price lower , the other is to bring all sorts of problems, such as brightness is not enough ,chip sealed plastic easily broken , chip aging too fast , etc. , resulting in the latter part of the maintenance costs rose sharply, not only reach the energy savings , the cost far beyond the use of energy inputs.

3 , LED power supply , price of an LED high bay light big impact factor is power supply , LED high bay light typically use the highest quality LED power production, there must be constant current regulator , dust- proof and waterproof effect, and corrosion resistance . LED high bay light power is also the most prone to the problem, a part of the manufacturers is to reduce the price of LED high bay light , using less power , resulting in a light-emitting chip instability , and the light fades faster, generally , mining lamps in a year later , the light intensity is significantly reduced , severe burning power even with the chip , and even lead to the factory fire and so on.

How to choose their own LED high bay lamp ? Hoe much price of LED high bay light is suitable ? How to choose ?Most customers started are most concerned about saving effects of LED high bay light , but in the consultation process , but all invariably inclined to LED high bay light prices ; actual fact, if you provide factory specifications and work demands ,TEK Lighting department colleagues will provide customers with the most suitable proposal does not require customers to blindly use high power LED mining lamp .if you only choose a low cost LED high bay light ,although a procurement cost savings at the beginning , but the mid you will found maintenance costs have soared, such as most of the factories are up to about 12 meters , the human cost of replacement LED mining light generated is enormous , followed by maintenance logistics costs generated in the process but also not low expenses , as a result of the replacement LED high bay light downtime , Has led to huge losses of the factory, so TEK recommends that customers only choice for right , do not blindly the pursuit of low prices of LED high bay light .

Click here to edit header

Click here to edit text.

Why led flood light have different price in market ?

Led flood light is popular in global ,but they have different price in mark . Why ? we can see what material led flood light need, such as chip , enclosure , driver , that is main material , also some others gadgets , but we talk with main material today. 

First of all , 10W chip of led flood light ,the most cheaper price is under 3$ in market now, that is unthinkable , if choose better one you must cost less 11$ . Of course , the best chip is less 18$ . The different between them a few time . Secondly  ，there is a market, there will be a manufacturing, need cheap housing, what manufacturer of shell, change material, thick bottom, high-power LED floodlight shell aluminum materials, the difference of aluminum materials have dozens of, this is also the shell manufacturer reduce the cost, the method of shell shell material changed, however, will be bad for heat dissipation?Will there be harm human body impurities? We don’t know .thirdly， Drive power supply, constant current constant voltage, above the drive, is very convenient, many electronic components can be replaced, even the same electronic components have high low, prices are different, if all use low electronic components, overall do a driven out, the cost is very low, driven by cheap, finished product omni can be cheaper。

the most let me worried thing, such a low price, also said 3-5 warranty years, without  price and quality assurance, that price is really can't imagine how low the cost pressure, really is not the bottom line. the most of people don't believe low price have good quality. Even so, some customers or be fooled by his low price. some customer want to buy a try . however , low price often mean not good quality so that people will not get long life span , environment protection , and so on . after some time , people will lose faith in led flood light . 

          Japan Chidorigafuchi Park using LED flood lights

For the Cherry Blossom Festival luster, Tokyo,Japan Chidorigafuchi Park using LED flood lights

Tokyo, Japan Chidorigafuchi Park installed solid state led flood lights to reduce the carbon footprint of the park, especially during the annual Cherry Blossom Festival, the park every night to be visited by thousands of viewers.

Transition from halogen to solid state 

lighting-led flood lighting , is to be replaced each fixture can save about 90% energy savings and carbon dioxide emissions, to promote Tokyo as a model of low carbon 

city.

In addition, LED cold light and ultraviolet radiation of led flood light will lower the flowers to create a more environmentally friendly environment that will help in the bestperiod of the annual cherry blossom viewing time as possible to keep longer.

How to choosing the reflectors for LED high bay?

How to choosing the reflectors for LED high bay?

In current markets, there are three different bean angle reflectors available for choice, 45°90°120°. It is hard for factory or warehouse owner to choosing the LED high bay light reflector.

Here is a simple way to choosing the LED high bay light light reflector:

Illuminance & distance

45degree beam angle LED high bay reflector recommend to using in distance between lamp to floor 8-12m high, the narrow beam angle makes lighting focus, thus we can get a high level flux on the floor or platform.

90degree beam angle LED high bay reflector recommend to using in distance between lamp to floor 6-8m high.

120deg beam angle LED high bay light reflector recommend to using in a distance between lamp to floor of 4-6m high, the 120 degree reflector could increase a wide range of irradiation.

If you have a warehouse or factory want to retrofit HPS, MH high bay to LED high bay light, you can contact with your LED high bay supplier to provide you a simple solution. Big factory used to have engineer dould use Dialux provide a simulation according to your project.

Customer or factory owner could according to your own project to select the suitable LED high bay lights.

What is a led flood light? Is what material composed of ?

First be noted that led flood lights not spotlight , lights, spotlights. Led flood lights produce a highly diffuse , non-directional light beam rather than clear-cut , resulting in soft shadows and transparent objects used for lighting , the lighting is much slower than weakened when illuminated with a spotlight , even some very slow weakening lighting of led flood lights , looks like a shadow of the light source does not produce . The spotlight projected orientation , clear boundary beam to illuminate a specific area. Light body material is aluminum alloy die casting surface treatment electrostatic spray coating temperature, anti-acid , anti-aging light body with light electrical integration design , compact structure, small reflector applications imported high purity aluminum , a variety of reflective surface design , with light to form a variety of different needs , high luminous efficiency, glare small light source can be customized according to customer needs, you can use the single-ended or double-ended metal halide or high pressure sodium lamp using E40 or RX7s mask is 5mm tempered glass, safe , high temperature, high strength , good transparency silicone rubber sealing strip of corrosion seals , sealing, waterproof , dustproof application of high performance ballast, igniter and capacitor , to ensure that lighting electrical performance requirements in line with GB internal Lian line 1mm2 PVC applied markers , stadiums , squares , trees , billboards , parking lots, building facades , etc.

Advantage of led flood light

Energy saving light efficiency : high efficiency , long life gas discharge lamp as the light source , high luminous efficiency , long life ; life up to 15,000 hours ; power factor greater than 0.9 , high luminous efficiency , good light transmission . Antiglare function : the use of advanced optical and lighting design principle of optimization transparent parts , soft lighting, illumination uniformity, no glare, effectively avoids visual fatigue staff.

The reasons of why LED high bay light choose reflector

LED high bay light is a kind of want to for a long time to use it to light, so we will save electricity demand is high in it. However, because of this we have to select a great combination of reflectors . Actually It is a reflector is used to gather the light effect , since it is the choice of the parabolic surface design principles , it is possible to consume a very low light efficiency . LED high bay lights are usually apply a light bead of high-power LED light source is called to do . When people choose reflectors can put it inside the hot air came in lights outside and lower the temperature, to ensure that the cooling effect and the use of time LED high bay light. Lights and electrical box cover book is best to cooperate to protect the divergence of heat and light . If the compact shape of the structure , which can achieve a decorative effect. The reflector is in fact the maximum effect of the LED illumination can be achieved such a reflective assembly quickly improve the utilization of the lamp , however, so that it presents the irradiated object even more realistic. Also had to make the atmosphere so that the environment to meet the requirements . Such reflectors can make the light softer eyes do not feel tired .

The most important thing is that the material used for the reflector , the majority of the normal state is selected aluminum alloy, is taken to do the high-purity aluminum reflector , so that it will be brighter irradiated light will even up, very effective blocking the strobe and glare , thereby protecting everyone's vision and can eliminate some of the problems caused by lamps with high color temperature . If you select a secure production businesses , the state will be observed under the hood usually there no matter what chemicals and broken glass posed , therefore so that consumers can be more peace of mind . Consumers will also believe the LED high bay light energy saving and environmental protection is seen increasingly heavy .

Retrofit High pressure high bay light project

Retrofit High pressure high bay light project

This is a retrofit traditional high pressure sodim lighting project, customer have a supermarket using 400W high pressure sodium lamp in bay lighting fuxture before, and he want to retrofit the bay light by a energy saving lamp as CFL or LED bulb. The 400W high pressure sodium high bay have ballast consider to another 80W power consumption, that means 480Watt in total. Now the customer using our 80W( total power consuMption 86W) LED bulb to replacement 400W HPS bulb, and also removing the ballast, they saving more than 80% than before, each lamp saving 394Watt per hour, that means they can saving 4728watt for each lamp lighting fixture in 12hrs working.

80W TEK LED corn bulb retrofit 400W HPS high bay lighting

TEK 80W LED corn light working in existing high bay fixture, perfect to replacement 400W HPS

 High Power 120W LED Corn Light

In November 2013, TEK Lighting lanches 120W High Power LED corn light with Mogul base E39/E40. Which special designed to replacement 400Watt HID lamps. Screw-in base type design, easy installation, just remove the ballast, connect to line voltage and your up and saving energy. The E40 base LED corn light operation voltage on 100-300VAC,50-60Hz. 3 years factory warranty.

Our High powered 120W LED corn light bulb special using aluminum fins heat sink with internal speed up the cooling fan, well control the temperature in 62±3℃.

New corn LED warehouse light 120W special use high brightness 2835 SMD LEDs, flux>15000lm (Typical: CCT:6000-6500K)

New LED corn light could used to replacement 400W HPS and 400W MH as warehouse lighting, factory lighting, workshop lighting.

Base type: Medium base(E26/E27);  Mogul base(E39/E40)
Color temperature: Warm white; Nature white; Cool white

Contact us now to get more information for 120W LED corn lights

List of top 3 LED high bay light manufacturer in China

In today’s global LED lighting markets, Chinese manufacturing are producing about 80% LED lights that are sold to worldwide. Most famous brand traditional lighting manufacturer, such as Philip and Osram’s original equipment manufacturer in China. If you need a LED lights, you can find it in China, there are a variety of LED factories that supply all kind of LED lights both indoor and outdoor.

In the past years, most of the industrial lighting using Osram brand metal halide lamp, high pressure sodium vapor lamp, mercury vapor lamp, mercury mixed-light lamp for open and enclosed luminaires, with the Philip brand MH lamp, HWL lamp, HPS, SON lamp, HQL lamps occupied most of the industrial lighting market. 

Today’s industrial energy saving lighting--LED high bay light mainly use in railway station, workshop, factory, warehouse, supermarket, port, gymnasium, exhibition Centre. LED high bay light perfect to replacement MH, HWL, HPS, SON, HQL traditional high bay lighting fixtures.

Here is the list of Top 3 LED high bay light manufacturer in China; some of these companies dominate the local markets, and some focus on global markets, some only make OEM for some branded LED companies.

1. TEKLED--Office in Shenzhen, China

In the year of 2008, most factory focus on home & commercial lighting developing and manufacturing. In view of the electricity prices of industrial lighting much more expensive than home lighting. TEKLED notice the markets of LED industrial lighting, and focus on LED high bay light, LED flood light, and LED corn light developing and manufacturing. The LED corn light series could directly replacement 70W-400W HPS, 80W-500W LED high bay light replacement 250W -1000W HID lamps.

2.  TEK Lighting Manufacturing Co., Ltd--Office in SZ, China

Focus on LED high bay lighting manufacturing more than 5 years, first LED high bay light manufacturing who provide 3 years warranty. Top LED high bay light factory with the capacity to make 20,000pcs per month

3. Hi-SE LED-- factory in Dongguang

LED industrial lighting factory Dongguang, focus on local LED markets and South-east Asia markets. 

Retrofit workshop lighting by LED high bay lightClick here to edit header

Click here to edit text.

  650pcs LED high bay light 

 As the leading manufacturer of LED industrial lighting in China,  TEK LED also provide OEM/ODM service. Recently, we received a ODM order for 650PCS 150W LED high bay factory lighting. The products will be export to Europe via our partner.

The IP65 LED high bay lighting could use in both indoor and outdoor, you can easy to use it replacement 400W MH traditional high bay lights, and 600W HPS bulb  hi bay in so many applications, such as warehouse lighting, factory lighting, store lighting, shopping more lighting, ice-rinks lighting, exhibition hall lighting

If you have an project need to retrofit LED lights, then contact with TEKLED today, our professinal lighting engineer will provide you a solution within 3 working days

The LED high bay light special use UL approval Meanwell driver, USA BridgeLux LEDs, the heat sink with copper heat-pipe for fast dissipation. 

5 years warranty LED high bay in TEK Lighting Technology Co.,Ltd

How will LED corn light actually benefit me?

We using Osram 64400 ECO 240V 70W E27 base mains voltage halogen lamp before, lumen 1180, we total have 1760PCS 70W Osram halogen lamps, we want to replacement by LED bulbs.

We search in google to find a retrofit LED lighting which could replacement our 70W halogen lamp, lumen no less than 1180lm. 

We have tried LED lamp called LED corn lamp in from a China supplier, the brightness very good, and could directly install in existing lighting fixture.

1760PCS 70W HALOGEN ABOUT 12Hrs per day-- Consumption of per month: >44000kwh

1760PCS 12W LED Corn lamp about 12Hrs per day--Consumption of per month: <9000kwh

Total LED corn light savings monthly: 35000Hrs

How to replacement E and ED mogul base metal halide bulb by LED?

Type E and ED mogul base metal halide lams high intensity discharge bulbs, high power 400Watt, including the ballast power, total power consumption: 480Watt. 

How can we replacement Mogul base 400W Metal Halide bulb by LED lights with the most economical way.

The answer is LED corn light. LED corn light design with mogul base type with 360 degree bean angle of light, view angle almost same as metal halide. And the screw base type same as metal halide mogul base which could directly screw into existing lamp socket, just by pass the ballast and install LED corn light, you can finish retrofit your traditional metal halide lamp to LED lighting.

LED corn light, brightness reach 110-120lm/Watt, CRI>75, lifespan of LED>50,000hrs. So mostly using 120W LED corn light to replacement 400W metal halide, more than 70% energy saving compared with MH lamp.

Different warranty between LED corn light and metal halide lamp.

LED corn light provide 3 years warranty, metal halide only provide 1-2year warranty. Please consider the maintenance supposing the metal halide high bay failed, it will be troublesome and cost you a lot of one light is hard to replace when stop working. Using LED lights with a longer lifespan means save maintain cost, products cost, and electric charges.

Get more informatiaon about replacement metal halide: www.ledcornlight.com

What is a LED high bay light?

LED high bay light is made of replace industrial high bay and low bay lighting fixtures, which using LED as light source.

TEKLED started LED lights business from 2008, which specialized in industrial LED high bay lighting developing and manufacturing, all LED high bay light provide 3 year factory warranty!

Where to use LED high bay light?
TEK LED high bay lighting has the advantage of high intensity and excellent heat dissipation. It can be widely used in outdoor and indoor lighting projects as emporiums, billboards, warehouses, gyms, parking lots

How to distinguish between good and bad LED high bay?

The most difficult to overcome of which is the heat dissipation problem of LED lights. 

TEK LED high bay light use Fin-style heat sink with heat-pipe design, which is much better for heat dissipation than normal alloy die-casting heat sink, and thous extends the working life of LED high bay lights.

What traditional lamps could replaced by LED high bay light?

LED high bay light could used both indoor and outdoor lighting, widely use to replacement traditional High pressure sodium(HPS), Metal Halide(MH), Compact Fluorescent Lamp(CFL), HQI, SON and mercury lamps in high bay lighting fixture, flood lighting fixture and low bay fixtures.

How to cut your annual energy with LED high bay lights?

How to cut your annual energy by 50% or more with LED high bay lights?

How to reduce HPS high bay lighting cost by over 50% with LED high bay light?

In the past years, High pressure sodium(HPS) lamp is the leading source of industrial illumination many decades. We can see High pressure sodium(HPS) high bay light fixture installed everywhere which produced by Philips, Osram and...

In China, We can see HPS high bay used in factory, warehouse, shopping mall, gymnasium center. Some owners still do not realized the important of energy saving. Due to they do not know how much money they can save from lighting cost.

Currently, we handle with a warehouse with 89pcs 250Watt High pressure sodium(HPS) lamp high bay light fixtures., light on 16hours per day

How many wattages that 250W HPS high bay actual used?

250W High pressure sodium(HPS) lamp high bay light fixture actual use 290Watts

According to our customer’s project information, lux level request, we could use 80W LED high bay light with 90degree reflector to replacement 250W HPS high bay light fixtures.

How to calculate the watts?

It is very simple, just simply the number of high bay lighting fixtures multiplid by the number of power consumption for your lights. So we have 89pcs 250W HPS

89lights x 290watts=25810 Total watts =25.81KWh

How many watts cost per year?

Customer need to light on 16hrs/day, about 4000hrs/year, then total Kwh/year:

25.81Watt x 4000hrs per year=103204KWh

How to calculate the cost of lighting cost?

In view of the warehouse lighting consider to industrial lighting, cost much higher than home lighting, about US$0.2/KWh

103204KWh* 0.2= US$20640.8 per year

But use LED high bay light, cost US$5980.8 only. The life span of HPS consider to 4000-6000hrs, LED high bay light life more than 35000hrs.

So you can easy to cut your annual lighting cost more than 60% with LED high bay lights. Contact us now to get more information for LED high bay light retrofit HPS high bay light fixtures.

How to Replace a warehouse light by LED high bay light

1. Check the working voltage before place an order, make sure the working voltage suitable for your warehouse. Mostly 85-265VAC enough, but different country have different working voltage, even same country have different working voltage for different application. Such as USA, home lighting usually consider to 120VAC, but industrial lighting consider to 277VAC or 480VAC, some also need 250VDC. It is very different. So check your working voltage before you purchase any replacement energy saving LED lights for your warehouses.

• Now you get a LED high bay light with good brightness, correct working voltage, then we start use a LED high bay light to replacement traditional warehouse lighting fixtures. Turn off the power to the switch at the main circuit breaker of fuse box. Test by flipping the switch on to make sure the power is off. 
• With a screwdriver, loosen the four screws from the high bay light heat sink, put the reflector holes into loosen screws, turn to the right place, and tighten four screws. Install the reflector to LED high bay light body as below:

• Find out the hook and screw-in the hook into hook’s hole on the top of high bay. In order to prevent the hook on the LED high bay falling from the installation site, please do not forget tighten the screw of the hook before hanging the LED high bay light.

• Put the LED high bay light fixture into existing high bay lighting fixed hanging hook. Find out the power supply wires, Brown color wire is Live Wire, Blue color wire is Null Wire, Yellow and Green wire is Ground Wire.

                  Brown-”L”

                  Blue-”N”

                  Yellow and Green- “Ground wire”

Correct connect the wire with a wire connector, “L” connect with Live wire, “N” connect with Null Wire, yellow and green connect with Ground line, tighten the screws both up an down. If you can not find wire connector, you can using insulating tape or insulating sleeve to protect the joint connect point. Or directly order correct plug for your LED high bay.

• After above operation finished, and then turn on the power.

Easy to use LED high bay light replace existing warehouse high bay lighting fixtures

How to choose the right color temperature for your LED lights

How to choose the right color temperature for your LED lights

Different places need different color temperature LED lighting, usually the LED lights consider to three colors, we call it warm white, nature white and cool white. LED lights for public applications to promote relaxation, people usually consider to choose the warm white which consider to 2800-3500K( K= Kelvin, Standard Unit for color temperature. And the cool white or nature white are usually consider to used to enhance concentration in office, workshop and repair Centre.

Some factory also producing CCT dimmable LED lights. The CCT dimming for LED technology is regarded as a difficult task. Usually consider set two types color temperature warm white and cool white into one LED lights, the power supply control system can freely to turn on the warm white color LEDs, or Cool white LED, and also turn on both cool white and warm white LED to get a nature color LED lights. 

The color temperature of LED lights consider to 1800K to 12000k, usually most LED lights consider to make CCT from 2800K-6700K, except some special applications as decoration or aquarium lighting, grow lighting.

How to choosing a right color temperature for your LED lighting products? 

Most people may asking:” What color temperature I should choose for my room, hotel, warehouse, jewelry shop, office? Should I have a certain color temperature?

Home LED lighting--Mostly home do not use cool color LED lights. Usually choosing warm color LED lights to built a warmer environment for home, color temperature consider to 2800-3500K in bed room, reading room use 4500-5500K, 

LED Building Lighting--Decorative LED lighting out of building use warm white or color LED flood light, red, green, yellow..., office and other places usually use cold white color LED lighting consider to 5500-6500K

Hotel LED lighting-- Lobby use cool white:5500-6500K, room use warm white:2800-3200K LED lights

LED warehouse lighting-- Warehouse Lighting usually consider to nature white (day white) 4000-5000K, or cool white 5500-6500K LED lights.

Industrial Plant LED lighting--Use nature white or cool white LED high bay lights.

Shipping mall LED lighting-- Use the cool white with CCT:6000-6500K.

Reference picture for LED lights color temperature:

Click here to edit header

How to install a LED high bay light?

Used for in-door & out-door, eg. the workshop, the storehouse, the road toll station, the gas station, the large-scalsupermarket, the exhibition hall, the stadium and so on which need lighting

LED high bay light applications:

Used for in-door & out-door, eg. the workshop, the storehouse, the road toll station, the gas station, the large-scale supermarket, the exhibition hall, the stadium and so on which need lighting

3. Using instructions

3. LED high bay light Using instructions

1. Working voltage: AC85-265V/277V  50-60Hz, Do not exceed the operating voltage.

2. Storage temperature:-25℃ ~ +65℃。 Working temperature: -40℃~+55℃。 Best working temperature: -0℃ ~ +30℃

3. The reflector of the light is easily deformed, so please handle with care and no press hard during transportion or storage.

3. Maintenance & repair instructions

4. LED high bay light Maintenance & repair instructions

1. Troubles resolution:

   Troubles and solutions: Observe the surface of LED light source whether there is discoloration, broken traces, with or without obvious fracture connectivity when you check. Please also check whether Power connection is loose & short-circuit, with or without obvious signs of damage. Please replace the light source and power if there is any obvious signs of damage.

2. Maintenance, repair Note

1)、 Please make sure the power-off before maintenance.

2)、 In order to maintain a good light transmittance, please clean the reflector of the industrial light regularly.

3)、 For maintaining good heat dissipation, please clean the dust on shell and the heat sink of the industrial light timely.

4)、 Please do not use water or corrosive cleaning liquor to clean, preferably with a dry cloth.

5)、 You may open the rear cover with a screwdriver, cut off the power when you replace the power supply.

     About the AC power three-pin wire, the bronw one is "L", the blue one is "N", the green&yellow one is Ground line. Regarding DC power wire, the red or white lines correspond to anode, and the black line corresponds to cathode. Please don't reverse the anode and cathode.

2. Maintenance, repair Note

1)、 Please make sure the power-off before maintenance.

2)、 In order to maintain a good light transmittance, please clean the reflector of the industrial light regularly.

3)、 For maintaining good heat dissipation, please clean the dust on shell and the heat sink of the industrial light timely.

4)、 Please do not use water or corrosive cleaning liquor to clean, preferably with a dry cloth.

5)、 You may open the rear cover with a screwdriver, cut off the power when you replace the power supply.

 Aout the AC power three-pin wire, the bronw one is "L", the blue one s "N", the green&yellow one is Ground line. Regarding DC power

 wie, the red or white lines correspond to anode, and the black line corresponds to cathode. Please don't reverse the anode and cathode.       

How to choosing the refelctors for LED high bay?

How to choosing the refelctors for LED high bay?

In current markets, there are three different bean angle reflectors available for choice, 45°90°120°. It is hard for factory or warehouse owner to choosing the LED high bay light reflector.

Here is a simple way to choosing the LED high bay light light reflector:

Illuminance & distance

45degree beam angle LED high bay reflector recommend to using in distance between lamp to floor 8-12m high, the narrow beam angle makes lighting focus, thus we can get a high level flux on the floor or platform.

90degree beam angle LED high bay reflector recommend to using in distance between lamp to floor 6-8m high.

120deg beam angle LED high bay light reflector recommend to using in a distance between lamp to floor of 4-6m high, the 120 degree reflector could increase a wide range of irradiation.

If you have a warehouse or factory want to retrofit HPS, MH high bay to LED high bay light, you can contact with your LED high bay supplier to provide you a simple solution. Big factory used to have engineer dould use Dialux provide a simulation according to your project.

Customer or factory owner could according to your own project to select the suitable LED high bay lights.

Industrial and mining lamp according to Ming floodlight function can be divided into general lighting and part two. 

Industrial and mining lamp according to Ming floodlight function can be divided into general lighting and part two. 
General lighting general evenly placed in the upper part of the job site or side walls, lighting for the whole operation, need to use power larger high intensity discharge lamp, halogen tungsten lamp and incandescent lamp or number of fluorescent lamp.The vast majority of industrial and mining lamp is such.General lighting spread have higher demand to the light, widely used direct lighting and half direct lighting two types of scattered light, especially the latter.Half part of the direct lighting type up announced light illuminates the ceiling, can add ceiling brightness, create a more comfortable, more bright environment. 
A job part part of the lamp is a kind of progress of illumination lamps and lanterns.It can effect is on the basis of general lighting strengthen, make up for the lighting, can also is not demand in some usual lighting places (such as equipment maintenance, maintenance) as a temporary lighting.Most of the light scattered no strict rules on them.Some light general in areas adjacent to use safety, low voltage (RMS) 50 v, or less communication of incandescent lamp, halogen tungsten lamp as light source.Line (portable) lamp, hanging lamp, desk lamp, machine work lamp, etc.In some large factories, and sometimes use project-light lamp for part of the lighting. 
Industrial and mining lamp according to the light source can be divided into traditional light industrial and mining lamp (such as sodium lamp industrial and mining lamp, mercury vapor lamp etc) and LED mining lamp.Compared to traditional industrial and mining lamp LED mining lamps and lanterns has big advantage: 
1 LED mining lamp show high RA > 75 
2 LED industrial lighting effect is high, more energy saving, the equivalent of 100 w LED mining lamp can instead of the traditional traditional industrial and mining lamp of 250W
3 traditional light source have drawback of the high temperature of lamps and lanterns, lamps and lanterns temperature can reach 200-200 degrees.And the LED itself is cold light source, lamps and lanterns of low temperature, the more security. 
4 LED mining lamp in constant vertical variations, the latest model of the fin type radiator industrial and mining lamp radiator more reasonable planning, greatly reduced the mining lamps and lanterns of the component, the whole weight of the 80 w LED mining lamp down to below 4 kg, and can successfully deal with 80-300 - w LED mining lamp cooling question.

What are the performance advantages of LED high bay lights are?

LED high bay lights are energy saving lamps, because the superior design and cooling effect, by the majority of companies use. Particularly on mining. Following a brief LED mining lamp performance advantages: 

1 excellent explosion-proof performance, can be used in a variety of flammable and explosive safety 

2. imported chips, LED packaging structure optimized to achieve low light decay, high luminous efficiency, energy saving and environmental protection, etc.; 

The power supply key components used brand in the world, to ensure lamp life; 

4 using crystal lens with light, to meet the lighting needs of different occasions; 

5 using pass-through design, optimize cooling structure, ensure lamp life; 

6 lamps using angle locking device, to ensure long-term changes still occur angle in vibration environment; 

7 Light body with light alloy materials, special sealing and surface coating, to ensure that lighting in the humid, high temperature and other harsh environments never corrosion, rust;

8 pedestal variety of installation methods and boom type and so on. 

Use LED mining lamp field: the shipyards, mines, workshops, factories, warehouses, highway toll stations, gas stations, supermarkets, exhibition halls, stadiums and other places need industrial lighting. 

Advantage 

1 imported LED chips, high luminous flux, energy-saving effect is obvious, saving more than 70% compared with sodium. 

2 decorative effect is excellent, the appearance can choose a variety of colors, simple installation, easy disassembly, a wide range. 

3 lifetime high of more than 50,000 hours, longer than traditional light sources over 10 times. 

4 green pollution-free, no lead, mercury and other pollution elements, no environmental pollution. 

5 color is good, the physical color rendering more real. 

6 with built-in or CE / UL external power supply to use, safe and reliable, able to work in -30 degrees to + 55 degrees for 3 years. 

7 good heat dissipation.......

How to replace sport center metal halide with LED high bay light?

In the past year, industrial metal halide high bay lighting widely u

Wide:31.6m
Length:21m
Height:5.5m

Our engineer will using DiaLux make simulation for your project

If you still worry about the brightness, of course, you can purchase samples to test it first.

Get more information for LED high bay lights? Contact us for more information now. TEKLED lighting--original LED high bay lighting manufacturer in China.

LED mining lamp features analysis:

LED high bay fixtures have multiple advantages, which are widely used in workshops, factories, mines, shipyards, gas stations, supermarkets, stadiums and other places. Specific analysis, LED mining lamp features include the following aspects: 

1, LED mining lamp advanced production technology, using a fan ventilation cooling, sufficient internal heat flow can be discharged, thus reducing its temperature, cooling requirements and protect the life of the LED light source, and light surface anodic oxidation processing, compact appearance. Thermal efficiency LED mining lamp uses a needle than traditional radiator radiator sheet is much higher than can make the LED junction temperature lower than the average over the radiator 15 ℃. 

2, LED high bay lamps have the characteristics of life, its unique chip technology fully guarantee the life of the light source. Coupled with the radiator and lamp shell integration design LED mining lamp, you can ensure that the entire lamp life. 

3, the unique LED mining lamp multi-chip integrated single-mode light source design, selection of imported high brightness chip, since the package power LED (60W - 160W) as the light source of its high thermal conductivity, low luminous decay, pure light color, no ghosting. Color is good, the physical color rendering more real, a kind of light color options to meet the needs of different environments, eliminating the traditional lamp color temperature is high due to low or depressed mood, so observe the Ministry comfort, improve worker efficiency. 

4, LED high bay lamps are energy-saving features, the use of multi-chip integrated high-power LED light source with high efficiency power supply, the same brightness than traditional energy-saving lamps more than 75%. 

5, LED mining lamp also has the advantage of green pollution-free, LED mining lamp does not contain aluminum, mercury and other pollution elements, it will not cause any pollution to the environment.

Click here to edit header

LED mining lamp is designed specifically for the mining industry, the production of lighting types, it has the following characteristics: 

1.LED mining lamp uses advanced LED technology, high-quality aluminum alloy material of the lamp envelope production, relatively high-strength aluminum alloy, and all aspects of performance is relatively stable, distortion does not occur in the case of long-term use of the process . Use of copper heat conduction and heat, plus aluminum heat, natural air circulation faster, heat dissipation is also more perfect, to some extent explains the LED mining lamp life longer durability. Meanwhile, on the other hand, because of its long life, the life of the lamp replacement period, eliminating the cost, overhead cost savings to the enterprise, which has brought benefits to the enterprise. 

2 LED mining lamp considering the particularity of the place of use, LED mining lamp uses a special explosion-proof design, and after manufacturing, making the LED mining lamp performance is relatively stable, with strong proof performance, very convenient to use and LED mining lamp has a certain dustproof, waterproof performance, high safety factor. Meanwhile, because of its place of use particularity, LED mining lamp production also takes into account their shock and anti-impact properties at relatively harsh environment can also be long-term use. 

3.LED mining lamp using a solid cold light source, is a new type of light source, with a little heat, high light efficiency and low power consumption compared to traditional incandescent and energy-saving lamp energy saving rate Seventy percent higher, is an energy efficient, ideal for mining operations lamps. 

4.LED mining lamp appearance relatively compact, easy to carry, can take many forms resettlement, ideal for use in factories and mines. 

LED high bay light is a new mining operation ideal lighting, the advantages of energy-efficient factories to save a lot of resources, and it does not contain mercury, lead and metal contamination, in response to a national advocate for low-carbon economy, energy saving ideas , is an ideal mining using lamps. 

High Power 300W LED High Bay Light with Heat-pipe

TEK LED high bay family (80-200Watt) has been extensively employed in all kind of industrial lighting since it was released to the market. In order to full fill the demand of higher wattage power supplies for the higher brightness lighting in the industrial LED luminaire markets, TEKLED announced the new 300W LED high bay light( TEK-IL-300W). This new model provide 90-305VAC full range input. 300W LED high bay light based on IP65 protection grade design that allow it works in various kinds of indoor or outdoor applications, could use in high dusty and high moist environment.

TEK 300W LED high bay light diffuser offers four designs with 30degree, 60degree, 90degree and 110degree beam angle. Suitable applications comprise factory lighting, sport center lighting, auto-part machining lighting, supermarket lighting, etc.

Features of 300W LED high bay lighting:

Rated Wattage: 300W

Input Voltage:90-305VAC

Operating frequency: 50/60Hz

Rated Power Factor:>0.5

Power Efficiency: >0.9

Humidity: < 90%

Ambient Temperature: -40~45℃

Protection Grade: IP65

Adjustable angle: 216°

Dimmable: No

Color temperature: Warm white:2800-3500K, Nature white:4000-5000K, Cool white:5500-6700K

Luminous Flux: 23747lm

LED Quantity: 192pcs CREE-XBD

Color Rendering Index: Ra>70

LED Emitter Life:>50,0000Hrs

          The performance characteristics of the led mining lamp is introduced

In the market of lamps and lanterns, there are a lot of different material is made, the lamps and lanterns of different use function, people according to the different functions of the lamps and lanterns of them used in different fields, before, we are all in use of said in our usual life lighting lamps and lanterns, that now, for we use less led mining lamp in our life, it will not be people use to household lighting, but use to many GongKuangYe, next, let us together into the led industrial light into the world, look at the led mining lamp is a kind of what kind of lamps and lanterns, how it compared with other lamps and lanterns has different features.

    Led mining lamp is a kind of special function used for industrial and mining industry design and production of kinds of lamps and lanterns, it mainly has the following advantages:
1, led mining lamp is durable, long service life.In our market of lamps and lanterns, the led mining lamps, almost all is the use of high quality aluminum alloy materials for the production of lamps and lanterns of the shell, the strength of the aluminum alloy is higher, all aspects of the performance is stable, therefore, after long-term use will not face the phenomenon of deformation, the surface is after a high voltage electrostatic pensu processing, makes the surface of lamps and lanterns is feels comfortable, long service life.
2, the led mining lamps and lanterns has certain explosion-proof performance.Considering the particularity of lamps and lanterns use place, we in the production of led mining lamp, have adopted a special explosion-proof structure design, and use to make the lamps and lanterns of toughened glass chimney, and through the die casting process of production, led mining lamp manufactured goods performance is stable, has a certain explosion-proof performance, use rise very convenient, high safety coefficient.
3, led mining lamp of high light efficiency, has the very good environmental protection performance.In led, after our many are using the led lamps and lanterns to make, led mining lamp, too, as we all know.Led is a solid cold light source, is a new type of light source types, using leds to produce industrial and mining lamp, with a very small heating rate, higher light efficiency and low power consumption, is a kind of ideal work lamps and lanterns of industrial appliances.
4, easy to use simple led mining lamp.We led mining lamp design, fully consider the particularity of the use place, therefore, when we design a led mining lamp from the exterior modelling of lamps and lanterns, the use of functional aspects of innovation, therefore, made the appearance of the led mining lamp modelling is compact, easy to carry, can use a variety of forms to put it.

Are you considering to replacement your 400W metal halide high bays?

When it cones to high bay lighting, metal halide is a thing of the past. Way to costly to run and maintain. In the past year, metal halide high bay widely used in all kinds of industrial and commercial lighting. Today, we have LED high bay light with low power consumption and high lumen output to fulfill that industrial energy saving lighting applications. With the developing of LED lighting, the price getting more cheap to purchase, and it’s almost maintain free, and cheap to run.

Why we need to replacement 400W metal halide?

400W metal halide(MH) lamp high bay light fixture actual use more than 440Watts. If you have 100pcs 400W MH high bay, 12hrs per day, then daily power consumption:

440x100x8=352KWh

Annual electricity consumption: 352*365=128480KWh

180W LED high bay light replacement 400W MH high bay, 180W high bay light fixture actual use more than 185Watts, if you using 100pcs 180W LED high bay to replace current 400W MH highbays, then daily power consumption:

195x100x8=156KWh

Annual electricity consumption: 156*365=56940KWh

Replaced by LED high bay light means you can saving 71540KWh per year.

Today’s industrial electric charge consider to US$0.2/KWh, 

400W MH high bay annual cost:US$25696

180W LED high bay annual cost: US$11388

So use LED high bay light could help you saving US$14308 per year. 

Are you consider to replacement your current MH high bay lights now? If yes, you can contact TEKLED for more LED high bay lighting information.

About LED Lighting

2.LED lighting features and advantages: 

  The study found, LED as a light source, energy saving, environmental protection, long life three major advantages, in theory, the energy consumption can be achieved only 10% of the consumption of incandescent, fluorescent energy saving than 50%. Because it uses a solid package, life is a fluorescent lamp 10 times, 100 times of incandescent lamp. Meanwhile, LED light without ultraviolet light, infrared light and other radiation, and can avoid the overflow of mercury in fluorescent mining lamp rupture secondary pollution. In the context of the global shortage of energy, LED growing concern for people. With a variety of colors have been successfully developed LED, LED from the initial indication for instrumentation, traffic lights, brake light (third brake light on the car), display (monochrome, color, full color). phone, lantern decoration (contour lights, fireworks and lights) to the current urban lighting, landscape lighting and other lighting project has been widely applied, showing a good development space and broad market prospects. At present, the color of the LED light source are mainly red, yellow, blue, green, white and full-color (RGB three-color, red, green, yellow primary colors composition), light angle also expanded from the original 60 to 120 degrees

LED revolution triggered

          US experts have pointed out, LED Semiconductor has completed a revolution in electronics, its second revolution will take place in the lighting field. Thus, an LED lighting craze sweeping the globe, setting off the lighting industry, "second revolution", the United States, Japan, Korea, Europe and other countries and regions have developed their own "semiconductor lighting plan." These countries around the development of LED technology in a fierce competition. From 2000 to invest US $ 500 million since the implementation of the "National Semiconductor Lighting Plan", the EU also in July 2000 announced the launch of a similar "Rainbow Project." Faced with the rise of a major transformation of the world and the LED lighting industry, China is also immediate action: Following the LED lighting included in the "15" national research programs, the state has an emergency start "semiconductor (LED) lighting industrial technology development of major projects "and established a leading group of semiconductor lighting project coordinated by eight ministries and determine Shenzhen, Shanghai, Dalian, Nanchang, Xiamen five cities for industrial demonstration bases. LED lighting industry unprecedented opportunities for development. At present, China's annual consumption of about 200 billion lighting --3000 billion kWh, according to the tariff calculation 0.8 yuan per kWh, the country if universal LED lighting, saving 160 billion per year -2400 million degrees, to save electricity more than a thousand billion. As such calculation, LED lighting indicates the future direction of development of the lighting industry. There are many domestic and foreign manufacturers to produce with LED floodlights, buried lights, lawn, light rails, etc., and are widely used in various spots decoration or city lighting project. And like LED lights, LED high bay light, LED tunnel lights, LED mining lamp, but also conform to the trend of getting into playing everyone's vision, its environmental protection and energy saving features to replace traditional lighting. LED lighting is another major contribution to semiconductor technology for human civilization and social development made​​, LED lighting technology is recognized as one of the twenty-first century high-tech areas most promising. With the continuous expansion of the LED lighting market, production scale and high brightness LED LED will be further expanded, the cost will be further reduced, so that the advantages in terms of performance, energy efficiency and service life can compensate for the high cost of its price disadvantage. Therefore, LED and high brightness LED lighting industry will become very competitive in the new power source. LED lighting revolution triggered at the same time, it will promote energy conservation, environmental protection, the establishment of a conservation-oriented society to make a significant contribution

Advantages of LED High Bay Light: 

Energy: the current luminous efficiency 100W LED mining lamp is about 1500lm, equivalent to 400W metal halide high bay light illumination, can also reduce the power consumption of about 60W rectifiers, saving more than 50% degree. 

Life: at the current level of technology and test results projections, LED mining lamp life up to 50,000 hours, while the traditional metal halide mining lamp life <5,000 hours, an average of less than one year to be replaced once, and some even three months will need to be replaced once. 

Green energy: Because there is no ultraviolet and infrared spectra, neither heat nor radiation, is the green light, comparing the previous traditional metal halide lighting, LED mining lamp reaches mercury resistance, recyclable waste, no pollution. 

Trend: countries have formally support the LED industry, increase the application of LED lights and sunlight mining lamps in the future development of LED's worth the wait.

ew Integrated LED high bay light

In Desember 2013, TEK Lighting lauches a new series Integrated LED high bay light. They have 120Watts to 300Watts LED high bay light available in this series, which designed to replacement 250Watt to 600W MH traditional bay lights.

The new designed integrated LED high bay make with waterproof and dust proof IP65 grade, suitable for use both indoor and outdoor applications.

Integrated LED high bay light heat sink use excellent quality aluminum, vacuum cavity of the thermal conduct, even one heat sink after more than 28 processes to make sure every piece of fin perfect connect with thermal cavity together, and whole heat sink connect without any screw and glue, in order to prevent the glue problem and fail down the heat sink hurt people.

Compare with the traditional extruded aluminum heat sink and conventional heat sink,the new integrated LED high bay light heat sink have advantage of lighter in weight, smaller in size, and cooling speed faster than 30%.

The integrated heat sink combined with vacuum heat pipe, the temperature will have a little rising when the constant temperature just begins, it will be stable in about half an hour, and temperature well contral in 60℃±3℃. Compare with other heat sink long time working will sharp increasing heat sink temperature, and the LED PCB temperature increased, it will be greatly increasing lumen decay, end LED high bay light life.

Acoording to Cree LED reports data shows, LED Tj>105℃， lifespan only a little longer than 10,000Hrs, LED Tj=95℃，LED lifespan>20,000hrs, LED Tj=75℃， LED lifespan>50,000hrs, LED Tj=65℃， LED lifespan>90,000hrs.

Also Lumiled LuxeonK2 LED droop cruve shows,

When LED Tj reach 115℃-135℃， LED lifespan will be reducing from 50,000hrs to 20,000hrs.

Then how to extend LED lifespan to extend LED high bay lifespan?
The keypoint is reducing the Junction temperature of LED high bay light.
How to reducing the LED juction temperature? The main point we need have a excellent heatsink which could release the LED heat fast.

TEKLED are adequately considered LED lifespan, and producing Integrated LED high bay light, well controlled the LED junction temperature in 60℃±3℃.

How to replacement 400W HPS high bay?

When it cones to high bay lighting, high pressure sodium(HPS) lamp is a thing of the past. Way to costly to run and maintain. In the past year, high pressure sodium(HPS) high bay lighting widely used in all kinds of industrial and commercial lighting. Today, we have LED high bay light with low power consumption and high lumen output to fulfill that industrial energy saving lighting applications. With the developing of LED lighting, the price getting more cheap to purchase, and it’s almost maintain free, and cheap to run.

How many wattage LED high bay light could retrofit existing 400Watt high pressure sodium(HPS) lamp high bay lights?

180W LED high bay light with high lumen output> 19000lm, could directly replace 400W HPS high bay lights in factory, workshop, supermarket, warehouses.exhibition center.

Can I save money from renew lighting project?

400Watt high pressure sodium(HPS) lamp high bay lights fixture actual use more than 440Watts. If you have 150pcs 400W HPS high bay, 12hrs per day, then daily power consumption:

440x150x8=528KWh

Annual electricity consumption: 528*365=192720KWh

180W LED high bay light replacement 400W HPS high bay, 180W high bay light fixture actual use more than 185Watts, if you using 150pcs 180W LED high bay to replace current 400W HPS highbays, then daily power consumption:

185x150x8=234KWh

Annual electricity consumption: 234*365=85410KWh

HPS:192720KWh

LED:85410KWh

If you use 180W LED high bay light replacement 400W HPS, you can saving 107310KWh per year.

Today’s industrial electric charge consider to US$0.2/KWh, 

400W MH high bay annual cost:US$38544

180W LED high bay annual cost: US$17082

So use LED high bay light could help you saving US$21462 per year. 

Are you consider to replacement your current 400W HPS high bay lights now? If yes, you can contact TEKLED for more LED high bay lighting information.

LED lighting manufacturer

http://www.ledcornbulbs.com/ LED lighting advantage

1, energy efficient at the same brightness, LED energy-saving than traditional fluorescent lamps more than 65%, since the LED light-emitting principle, can the maximum efficiency of converting electrical energy into light, white LED's energy consumption is only 1/10 of incandescent lamp, Yes CFLs 1/2 for example: an ordinary 60CM Grille, by three 18W lamp ballast plus three 5W, whose total power is 69W. The selection of LED lamps, it has reached its same effect, as long as the three 8W lamp components, and does not require selected ballast, the total power of 24W, according to the test, in fact, reach 24W. This contrast, each set Grille saving 69W-24W = 45W of power, equivalent to a 65% saving in electricity. If a monthly lighting electricity companies for 100,000 RMB, then use LED, then it only takes about a month 30,000-40,000 RMB, the presentation of the effect is quite obvious.

2, high light efficiency LED lamp heat, 80% of the electrical energy into visible light (80% of the ordinary incandescent electric energy into heat, only 20% of electrical energy into light energy) 

3, fast response speed of the order of tens of milliseconds average response ease of use. 

4, sturdy solid LED lamp uses light emitting semiconductor chips, no filament, not afraid of vibration, not broken, solid package, easy to transport and install. 

5, the use of carbon per kilowatt effect, its carbon dioxide emissions of about 0.62KG. LED energy-saving fluorescent lamps compared to 65%, compared to metal halide, incandescent 75-85%, 50% energy saving lamps to reduce carbon dioxide emissions by 50-85%. Play a role in protecting the environment. 

6, long durable life of up to 50,000 hours (incandescent life of only 1,000 hours, ordinary energy-saving lamp life are 3000-5000 hours), you can often turn a million times (hundreds of energy-saving lamps fold), for ordinary home lighting can be described as "once and for all." 

7, light healthy LED lighting line does not contain ultraviolet and infrared light, does not produce radiation (ordinary energy-saving lamp contains ultraviolet and infrared). 

8, the green LED lights do not contain mercury and xenon and other harmful elements, conducive to recovery, but does not produce electromagnetic interference (high pressure sodium lamp contains mercury, xenon and other elements, including electronic ballasts will produce electromagnetic interference). 

9, protect eyesight LED light particles using DC drive, no flash.

LED High Bay Light with ordinary mining lamps have those advantages

LED mining lamp using a fourth-generation light source, he more than other light sources, such as incandescent lamps, high pressure sodium lamp, high pressure mercury lamp, lamp has the following advantages: Voltage: LED mining light source using a low power, single voltage between 1.9-4V safer than the use of high voltage power supply.

  Effectiveness: High luminous efficiency, the current laboratory highest luminous efficiency has reached 161 lm / w (cree), is currently the highest light efficiency lighting products. Theoretically LED luminous efficiency per watt up to 370 LM / W, under the current chip structure in good condition without any change in the process so that every watt LED 150LM arrive without any problems, this brightness is reached, all the lighting in the area basically can be replaced. Expected in the next 1-3 years, LED light will reach 300 lumens per watt light efficiency. The US laboratory LED has reached 161 lumens of light per watt efficiency, total luminous flux 175 LM.

Shock resistance: LED is a solid-state light source, due to its specificity, with other lighting products can not be compared shock resistance. Stability: 100,000 hours, the light fades to the initial 70%

Response time: Response time LED lights nanosecond, is currently the fastest response time of all light products.

   Environmental protection: no metallic mercury and other harmful substances.

Color: LED fast fairly narrow band, the light color, color purity, non-variegated light, covering the entire band over the entire visible light, and can be a combination of R \ G \ B to anyone who wants to visible light.

Life: LED average life 5000-100000 hours, greatly reducing your maintenance and replacement costs. Found in the LED light source excellent characteristics, Guoguang Green started research and development of LED mining lamp, the light LED mining lamp uses Guoguang independent self-developed heat sink, better performance, light use international big LED chip packaging, CRI excellent (greater than 80 ), quality and security, and truly done and keep practical and beautiful.

  LED mining lamp suited for large-scale factories, warehouses, petrochemical, swimming pool, gymnasium, coal, iron ore, all kinds of mines. High Power LED Bay Light is currently on the market is the most excellent lighting, for more support, please call 150-1411-5394 Miss Yu.

 Why LED high bay light reflector reasons to choose

LED High Bay Light It is a very long time to use its light, so we will save its energy requirements are relatively high. However, because of this we have to choose a great combination of reflectors. Its role in the reflector is actually used to gather the light as it is chosen the principle of parabolic surface design, it is possible to consume a very low light efficiency. LED high bay lights are usually apply a bead of high-power LED light source of light is called to do. When people choose reflectors can put it inside the hot gas discharge lamp and lower the temperature outside, to ensure that the cooling effect and the use of time LED mining lamp. Lights and electrical box cover book best fit to the divergence of heat and light protection. If the compact shape of the structure, which can reach a decorative effect. Indeed reflector for maximum effect is to make LED lighting can not reach such a fitting reflection, and soon raised the lamp usage, however, makes the irradiated material it presents even more real. Also have to make such an atmosphere environment to meet the requirements. Such reflectors can make the light softer eyes do not feel tired.

The most important thing is that the reflector material it uses, most normal state selected aluminum alloy, is taken to do the high-purity aluminum reflector, so that it will be more irradiated with light, the light will be evenly together, very effectively block the flash and glare, thereby protecting everyone's vision and can eliminate some of the problems brought about by the lighting color temperature is high. If you choose a secure production businesses, usually the state will observe the hood there any chemicals and substances composed of broken glass, so this can be more at ease consumer confidence. Consumers will also believe that the LED mining lamp energy saving and environmental protection is becoming increasingly important to see.

Click here to edit header

The intrinsic characteristics of the LED determines that it has many advantages, such as:

1, small

LED is basically a small chip which is encapsulated in epoxy, so it is very small, very light.

2, low power consumption

LED power consumption is very low, DC drive, ultra-low power consumption (single tube 0.03-0.06 W), electro-optical power conversion close to 30%. In general LED's operating voltage is 2-3.6V, operating current is 0.02-0.03A; that is, it does not exceed power consumption 0.1W, the same lighting effects than traditional energy sources, nearly 80%.

3, long service life

Some have called for the long life LED light source lamp. It is solid cold light source, epoxy resin, light body and no loose parts, there is no filament light easy to burn, heat deposition, the light fades and other shortcomings, at the right current and voltage, the service life of up to 60000-10 million hours long life than conventional light sources more than 10 times.

4, high brightness, low-calorie

LED light technology with cold, much less heat than conventional lighting.

5, environmental protection

LED is made from non-toxic materials, unlike fluorescent lamps containing mercury can cause pollution, while LED can also be recycled. No ultraviolet and infrared spectra, neither heat nor radiation, little glare, cold light source, safe touch, typical of the green lighting

6, durable

LED is completely encapsulated in epoxy resin inside than light bulbs and fluorescent tubes are solid. Part of the light body and no loose, making the LED is not wearing

LED lights

Bad.

7, many changes

LED light source can use red, green, and blue color theory, under the control of computer technology to make three colors with 256 gray scale, and any mix can produce 256 × 256 × 256 = 16777216 colors, to form different combinations of light and color varied to achieve a variety of dynamic effects and variety of images.

8, advanced technology

Compared with the traditional light monotonous glow, LED lighting is low voltage microelectronic products. It is the successful integration of computer technology, network communications technology, image processing technology, embedded control technology, so it is also digital information products, is semiconductor optoelectronic devices, "high point" technology, with online programming, unlimited scalability, flexible Features.

200W LED high bay light UL listed Meanwell driver:

 200W LED high bay light recommend to replacement 400W metal halide high bay lighting fixture

200W LED high bay light replacement 450W Metal Halide & 600W HPS Bulb high bay lighting fixture , 70% energy saving compared with hgih pressure sodium.lighting    Advantages of LED high bay warehouse lighting 

1.IP65, Aluminum Fins Heatsink + double thick Alu Body 

2. 45mil 110-120lm/W high brightness BridgeLux LEDs 3

3.UL approval Mean Well driver 

4. Finished with epoxy powder paint,resistant to corrosion. 

5. CRI>80, excellent color redering 

6. CE & RoHS certified, comply with UL certificated 

7. Different color available 

8. Warranty; 2 years or 3 years 

9. Estimated life time 2 to 3 times that of Metal Halide or  9. Full range series LED high bay lights, 80W high bay, 100W high bay lighting, 120W LED bay light, 150W retrofit fin LED high bay warehouse light, 200W LED high bay lights.  

 Technocial Specification:   

Application: Widely used indoor and outdoor commercial lighting as gym lighting, factory lighting, parking lot lighting, illumination for house, shopwindow, display hall,shopping mall lighting, commodity excite exhibition room and billboard; Gymnasiums lighting, factory lighting, advertising board lighting, etc...     

Tek Lighting Manufacturing LED high bay light:   

1.Original LED high bay light manufacturer in China,  

2. Tek Lighting already exported LED lights to over 70 Countries 

3. We have more than 100 stuffs, and the 6 engineers in R & D department 

4. IES simulation supports   Notes: * Read LED high bay lights specification before installation * Recommend use both indoor lighting and outdoor lighting * The LED high bay light must work uner the right voltage according to specificatio200W LED high bay light replacement 450W Metal Halide & 600W HPS Bulb high bay lighting fixture , 70% energy saving compared with hgih pressure sodium.lighting 

Advantages of LED high bay warehouse lighting:

1. IP65, Aluminum Fins Heatsink + double thick Alu Body

2. 45mil 110-120lm/W high brightness BridgeLux LEDs

3. UL approval Mean Well driver

4. Finished with epoxy powder paint,resistant to corrosion.

5. CRI>80, excellent color redering

6. CE & RoHS certified, comply with UL certificated

7. Different color available

8. Warranty; 3 years

9. Estimated life time 2 to 3 times that of Metal Halide or HPS

10. 200W LED high bay light recommend to replacement 400W Metal Halide or HPS high bay light

TEK Lighting LED high bay lights: 80W LED High Bay Light, 100W LED high bay lighting, 120W LED bay light, 150W retrofit fin LED high bay warehouse light, 180W LED High Bay Lights, 200W LED high bay lights.

LED flood light Product Description

New LED flood light 200W to replacement Mercury Halide & HPS Bulb flood light 600W

Core Features:                                                                                                   

1. Light body: Aluminum Fins Heatsink +Tempered Glass Cover+silicon rubber sealing gasket

2. 45mil 110-120lm/W high brightness BridgeLux LEDs

3. UL approval Mean Well driver

4. Finished with epoxy powder paint,resistant to corrosion.

5. Unique aluminum fins sheet heat sink design, better for heat disspation, extent LED flood light lifespan

6. CE & RoHS certified, comply with UL certificated

7. Different color available

8. Warranty; 2 years or 3 years

9. Full range series LED flood lights, available in 10Watt, 20Watt, 30Watt, 50Watt, 80Watt, 100Watt, 120Watt, 150Watt, 160Watt, 200Watt models availbe for your choice

High Power 300W LED High Bay Light with Heat-pipe

TEK LED high bay family (80-200Watt) has been extensively employed in all kind of industrial lighting since it was released to the market. In order to full fill the demand of higher wattage power supplies for the higher brightness lighting in the industrial LED luminaire markets, TEKLED announced the new 300W LED high bay light( TEK-IL-300W). This new model provide 90-305VAC full range input. 300W LED high bay light based on IP65 protection grade design that allow it works in various kinds of indoor or outdoor applications, could use in high dusty and high moist environment.

TEK 300W LED high bay light diffuser offers four designs with 30degree, 60degree, 90degree and 110degree beam angle. Suitable applications comprise factory lighting, sport center lighting, auto-part machining lighting, supermarket lighting, etc.

Rated Wattage: 300W

Input Voltage:90-305VAC

Operating frequency: 50/60Hz

Rated Power Factor:>0.5

Power Efficiency: >0.9

Humidity: < 90%

Ambient Temperature: -40~45℃

Protection Grade: IP65

Adjustable angle: 216°

Dimmable: No

Color temperature: Warm white:2800-3500K, Nature white:4000-5000K, Cool white:5500-6700K

Luminous Flux: 23747lm

LED Quantity: 192pcs CREE-XBD

Color Rendering Index: Ra>70

LED Emitter Life:>50,0000Hrs

                               How to choose led flood light ?

1, LED flood lights luminance (MCD) is different, the price is different. Used for LED lamps and lanterns, the LED should comply with the laser level Ⅰ class standard.

2, antistatic ability of LED, long life, so price is high. Antistatic usually greater than 700 v LED can be used in the LED lighting.

3, wavelength consistent LED, color is consistent, if request the same color, the price is high.Not the manufacturer of the LED light color separation instrument is not easy to produce pure color products.

4, the leakage current of LED floodlight is a one-way conductive lights, if there is a reverse current, is called the leakage, leakage current big LED, short service life, low price.

5, use different LED light Angle is different.Special light Angle, the price is higher.Such as the diffuse Angle, the price is higher.

6, quality is the key to life, life is decided by droop.Droop small, long service life, long life, high price.

7, LED flood lights for chip, different chip, price difference is very big.Chip is more expensive, Japan, the United States generally chips in Taiwan and domestic price is lower than the day, the United States (CREE).

8, the size of the chip to side, said big LED chip quality is better than that of the small chips.The price is proportional with the chip size.

9, ordinary LED colloid generally for epoxy resin, Leds with UV radiation and fire retardant added more expensive, high quality outdoor LED lighting should be UV and fire prevention.

Each product can have different design, different design suitable for different purposes, the reliability of the LED lighting design aspects include: electrical safety, fire safety, environmental safety, mechanical safety, health and safety, security, time and other factors.

From the perspective of the electrical safety shall comply with relevant international and national standards.Because of the LED is a new product, the national standard lag, but countries to provide product qualification testing.With international safety certification (such as GS, CE, UL, etc.) and the national product quality certification of the LED lamp price is higher, because these products on the safety design is reliable.The attention of consumers is to carefully identify certificate of authenticity, now has the international safety certification and the national product certification factory is not much.

From the aspects of health, the use of non-toxic materials, design of the product price is higher, especially the indoor LED floodlight, don't keen on gaining petty advantages chooses is faulty LED lamp act the role ofing, currently only a small number of LED manufacturers is to use non-toxic materials production, to identify the method can directly use the nose, smelly products price more lower than without bad smell.Similar toxins such as lead, mercury, cadmium needs professional analysis.d, mercury, cadmium needs professional analysis.

                     Why Led high bay light so expensive ?

Led high bay light is more and more recognized by people , most advantages of led high bay light is loved by people , but its expensive price still let people hesitate. Why led high bay light so expensive ?

Long life span and green is advantage of led high bay light , however , if you want to achieve this effect , you must use Mean well driver and Cree chip . As we all know , Mean well driver is the nobles of the drivers. Its price is impossibility to low, so if you have low price when you buy , you had to worry about whether you buy not a real led high bay light or not. A good driver is the reason of long life span , Cree chip is the guarantee of green.

In addition to that , due to Cree chip will produce a lot of heat. Led high bay light must need supper heat sink . A good quality heat sink is very expensive in China .

Led high bay is made of chip , driver, heat sink and thick body , a quality manufacturer will use best accessories, such as TEK lighting technology use double thick Aluminum body for protect chip. 

                   What should notice to choose led high bay light?

Lighting market , there are made of many different materials, different use of functional lighting , people depending on the functional role of these lamps use them to different areas in the past, we are talking about our usual life lighting fixtures , now we use it in our lives less led high bay light it, it will not be using it to home lighting , but use a lot of work into the mining industry , then, let us into the led high bay light the world , and see what led high bay light is what kind of lighting, it is compared with other lamps and how different characteristics.

Led High Bay Light is a specially designed lamps using the kind of role mining industry , which mainly has the following advantages:

1, Led high bay light durable, long life . In our lighting market , led mining lamp almost always use high-quality aluminum alloy material for the production of shell lamps , high -strength aluminum alloy , all aspects of performance are relatively stable, and therefore , after long-term use is not line phenomenon becomes deformed , its surface is the result of a high-voltage electrostatic spray treatment makes the surface of the lamp comfort grip and long life.

2, Led high bay light have some proof performance . Taking into account the special nature of luminaires location , we produce led high bay light when using a special explosion-proof structure design , and the use of tempered glass to make lamp shade, plus a die-casting process through production, led high bay light makes the finished product more stable performance , with some proof performance , very easy to use , high safety factor .

3, Led high bay light efficiency is high, with good environmental performance. After led occur , many of our fixtures are led to make use of , led mining lamp , too, as we all know . Led is a solid cold light source , the light source is a new species, use led to the production of mining lamps, with a little heat rate , a relatively high light efficiency and low power consumption rate , is an ideal mining job lighting appliances.

4,Led high bay light is simple and easy to use . We led high bay light when the design fully into account the particularity of place of use , so we design led high bay light when the lamp to transform innovation in terms of appearance , functionality and, therefore, made out of led high bay light appearance compact, easy to carry , can take many forms to accommodate it .

Led flood light is popular in China

Led flood light is popular is china , people use it in the park , hotel lawn , garden , and so on . Its perfect color rendering index will bring customer a new feel that is Incandescent lamp, high pressure sodium lamp, energy saving lamp couldn't do 

People used led flood light as street light in Changzhou, jiangsu province , of course , under led flood light shine , this place so beautiful so that become one of the place of people love to go . 

if you want to know more information , please to contact us!

                        Led flood light is used in the park 
Led lights is more and more popular in global, people used led flood light replace traditional flood light , people used led flood light in the park , lawn , gym .

What is a led flood light?
Led flood light is a kind of can be all directions even illuminate the point light source, it can adjust the illuminate of scope, characterized by a positive octahedral icon. The Floodlight To render the most widely used production source, standard led flood light lights used To illuminate the whole scene. Led flood lighting can be used in the scene. To produce a better effect To the bulb into a large reflective umbrella, used for the transmission of high brightness of the light source.

how to use led flood light?
Needed materials: LED guardrail lamp clamp, transformer with waterproof function, sub control device, the steps are as follows.
1, install guardrail, holes in the wall, spacing, according to the practical requirements of general within 3 cm;
2, good anti-static measures, such as the workbench to grounding, workers wear corresponding electrostatic clothing, anti-static measures, because different grade of quality of LED flood light, different antistatic ability strong or weak;
3, installation, pay attention to sealing, sealing, affect the service life of LED flood light diameter;
4, LED flood light wiring had better not exceed 25 cm, corresponding to a large power transformer can be longer, otherwise affect brightness.


Note

1, try to use the series of LED form, because the LED floodlight special voltage difference.Ordinary LED the peak current is maintained at 80 ma, reverse voltage in 6 v, up and down in the LED application should pay attention to when designing circuit peak voltage and current under the limit.

2, when welding using voltage below 25 watt, control the solder iron temperature below 300 degrees Celsius in the condition of high temperature exposed SMD LED, don't squeeze the epoxy resin is part of it, or with a sharp object to wipe, because LED lamps and lanterns is very fragile, easily damaged, welding time for 3 seconds.


LED flood light is widely used, so the installation techniques and matters needing attention is very important, new light source, LED is under the correct installation, to ensure the normal work of the LED flood light stable for a long time.

                     Japan Chidorigafuchi Park using LED flood lights

For the Cherry Blossom Festival luster, Tokyo, Japan Chidorigafuchi Park using LED flood lights

Tokyo, Japan Chidorigafuchi Park installed solid-state led flood lights to reduce the carbon footprint of the park, especially during the annual Cherry Blossom Festival, the park every night to be visited by thousands of viewers.

Transition from halogen to solid-state lighting--led flood lighting , is to be replaced each fixture can save about 90% energy savings and carbon dioxide emissions, to promote Tokyo as a model of low-carbon city.

In addition, LED cold light and ultraviolet radiation of led flood light will lower the flowers to create a more environmentally friendly environment that will help in the best period of the annual cherry blossom viewing time as possible to keep longer.

               The reasons of why LED high bay light choose reflector

LED high bay light is a kind of want to for a long time to use it to light, so we will save electricity demand is high in it. However, because of this we have to select a great combination of reflectors . Actually It is a reflector is used to gather the light effect , since it is the choice of the parabolic surface design principles , it is possible to consume a very low light efficiency . LED high bay lights are usually apply a light bead of high-power LED light source is called to do . When people choose reflectors can put it inside the hot air came in lights outside and lower the temperature, to ensure that the cooling effect and the use of time LED high bay light. Lights and electrical box cover book is best to cooperate to protect the divergence of heat and light . If the compact shape of the structure , which can achieve a decorative effect. The reflector is in fact the maximum effect of the LED illumination can be achieved such a reflective assembly quickly improve the utilization of the lamp , however, so that it presents the irradiated object even more realistic. Also had to make the atmosphere so that the environment to meet the requirements . Such reflectors can make the light softer eyes do not feel tired .

The most important thing is that the material used for the reflector , the majority of the normal state is selected aluminum alloy, is taken to do the high-purity aluminum reflector , so that it will be brighter irradiated light will even up, very effective blocking the strobe and glare , thereby protecting everyone's vision and can eliminate some of the problems caused by lamps with high color temperature . If you select a secure production businesses , the state will be observed under the hood usually there no matter what chemicals and broken glass posed , therefore so that consumers can be more peace of mind . Consumers will also believe the LED high bay light energy saving and environmental protection is seen increasingly heavy .

              lampshade of led high bay light is made of aluminum substrate 

lampshade of led high bay light is made of aluminum substrate .Aluminum base plate is a metal having good heat dissipation CCL, generally consists of three single-panel structure, namely the circuit layer (foil), the insulating layer and the metal substrate. Also used for high-end dual-panel design, the structure of the circuit layer, an insulating layer, aluminum, an insulating layer, a circuit layer. Very few applications of plywood, plain plywood can be made with the insulating layer, aluminum bonding together. 

LED aluminum plate is the PCB, the PCB also mean, just the circuit board material is aluminum, we used the average fiberglass circuit board material, but because the LED heat larger, so the board is generally used for LED lamps aluminum plate, can heat quickly, electrical circuit boards or other equipment used in class or fiberglass board. so chip of led high bay light can produce heat as soon as possible to the heat sink .

Works principle 

Power device surface mounted on the circuit layer, the heat generated during operation of the device through the insulating layer to a conductive metal substrate quickly, and then the metal substrate to transfer heat out of the cooling device in order to achieve 

Superiority 

And the ratio of the conventional FR-4, the thermal resistance of the aluminum substrate can be minimized, so that the aluminum plate having an excellent thermal conductivity; compared with the thick film ceramic circuit which is extremely excellent in mechanical properties. 

In addition, aluminum plate as well as the unique advantages: 

1, with RoHs requirements; 

2, more adapted to the SMT process; 

3, the circuit design of the thermal diffusion in a very effective treatment, thereby reducing the module operating temperature and prolong life, increase power density and reliability; 

4, reduce the heat sink and other hardware (including thermal interface material) assembly, smaller footprint, lower hardware and assembly costs; 

5, the power circuit and control circuit optimization portfolio; 

6, replace the fragile ceramic substrates, better mechanical durability. 

Led high bay light use aluminum substrate as lampshade , can get better benefit. People don’t havt to worry about the problem of heat dissipation . 

                   Why led flood light have different price in market ?

Led flood light is popular in global ,but they have different price in mark . Why ? we can see what material led flood light need, such as chip , enclosure , driver , that is main material , also some others gadgets , but we talk with main material today. 

First of all , 10W chip of led flood light ,the most cheaper price is under 3$ in market now, that is unthinkable , if choose better one you must cost less 11$ . Of course , the best chip is less 18$ . The different between them a few time . Secondly  ，there is a market, there will be a manufacturing, need cheap housing, what manufacturer of shell, change material, thick bottom, high-power LED floodlight shell aluminum materials, the difference of aluminum materials have dozens of, this is also the shell manufacturer reduce the cost, the method of shell shell material changed, however, will be bad for heat dissipation?Will there be harm human body impurities? We don’t know .thirdly， Drive power supply, constant current constant voltage, above the drive, is very convenient, many electronic components can be replaced, even the same electronic components have high low, prices are different, if all use low electronic components, overall do a driven out, the cost is very low, driven by cheap, finished product omni can be cheaper。

the most let me worried thing, such a low price, also said 3-5 warranty years, without  price and quality assurance, that price is really can't imagine how low the cost pressure, really is not the bottom line. the most of people don't believe low price have good quality. Even so, some customers or be fooled by his low price. some customer want to buy a try . however , low price often mean not good quality so that people will not get long life span , environment protection , and so on . after some time , people will lose faith in led flood light . 

 problem of led street light in the application 

In the global energy crisis and environmental pressures increasingly prominent situation, LED light source used in road lighting has become a hot spot in recent years, the semiconductor lighting industry. LED device products applied to the lights, there are no special requirements for technology,What is advantagesand weakness of LED street lights compared to traditional high pressure sodium street lights currently ? how to solve a series of problems that we are worthy of serious study. 

1, the basic product standardization and commonality of large-scale use 

Currently launched LED street lights, product appearance, dimensions LED light-emitting particles arranged manner and quantity, the rectifier circuit and a variety of interior design. Such as: the number of single-tube power varies, ranging from 1 to 5 watts; different light distribution, there are bat-shaped, rectangular, Butterfly type, etc.; optical approach has its own free secondary optical lens and a second optical processing processing; driver situation has dedicated driver IC chip and no electrolytic capacitors; package multiple chip package and Billing Division situations chip packaging; technical line conditions have mold, the group of high-power, high-power chip, power and other dot-matrix . Power also has its own assembly and integration of two external power, cooling technology is different, which gave the popularity of running and maintenance after use has caused great inconvenience, does not conform to municipal utilities standardized, universal design principles. 

We believe that in the future the development process, the manufacturer should be strictly in accordance with national standard to ensure product safety and electrical equipment safe and reliable performance. Meanwhile, the city has been applied in the field of LED lighting products, the product must be standard, offers the following guarantee unity. 

Such as: For the same between the different stages of development of enterprise products, to ensure the standard of the main electrical components, unity, to avoid causing product replacement spare parts dating; between different enterprises for products, lighting body, emitting particle board The main electrical components, rectifier circuits should be based on national standards, to achieve the necessary standards and unity. 

2, the corresponding national standards to protect the healthy development of LED street light market 

Optical and thermal characteristics of LED and traditional light sources varies greatly, so that the existing LED measurement methods of measurement can not be fully applied to traditional lighting source. LED current in terms of product specifications or measurements were lack of proper standards, product variety, no standard measure, the market is not standardized, and the diversity of products has also led to large-scale production enterprises can not concentrate. The development of relevant standards has become an urgent demand for LED industry. At present, the National Standardization Technical Committee and other lighting appliances in the submittal phase, expected to be successively promulgated "LED general lighting made with national standards and industry standards." Companies should make a new market positioning and product planning, seize new opportunities, to invest the necessary quality assurance measures.

                    Ten advantages of LED high bay light 

1,LED is very small, very fine chip encapsulated in transparent epoxy resin inside, so it is very small grain , very light , in the production and application can save a lot of material and space.

2, Rugged and durable

LED chips are completely encapsulated in epoxy . Compact epoxy resin particles is extremely difficult smashes , the entire light body and no loose parts ; inside the chip is extremely difficult to break , and very few thermal effects which may volatilize blown. These features make the LED difficult to damage. Compared with ordinary light bulbs, fluorescent lamps , LED can be described as impregnable, countless times rugged , durable countless times .

3, long life

In the right current and voltage , LED life of up to 100,000 hours , that theoretically the product life of more than 10 years , is the only long-lived star lighting fields.

4,Low voltage safety

LED using low voltage DC power supply ( can be rectified AC to DC ) , power supply voltage between 6 ~ 24V, because different products vary . In short it is more secure than application of high voltage DC power supply , especially for homes and public places.

5,Wide range of applications

Because small, small piece of each LED unit is 3 ~ 5mm square or round , so more suitable for the preparation of molding process complex devices . For example, the manufacture of soft , flexible tubes , lights , shaped snuff , is currently the only LED fit.

6,richer colors

Before lighting color is very simple, in order to achieve the purpose of color , one paint brush or the surface of the light colored cover sheet , the second is filled with inert gas glow in the lighting , so the richness of colors is limited . LED digital control , LED chips currently able to issue a variety of colors , including red , green, blue three primary colors , precisely because of this ternary color , controlled by the system , you can restore the colorful worlds .

7, less heat dissipation

LED cold light source is more advanced , unlike incandescent, fluorescent , as a large number of infrared and ultraviolet radiation , especially for lighting artifacts, jewelry, luxury cosmetics and other valuables. Almost no thermal effect of current incandescent like that, but not affected by thermal expansion and contraction of the bubble fried . Will not make the bulb yellow, will not make lamps accelerated aging , does not constitute the greenhouse effect on the surrounding environment.

8,less environmental pollution

LED for the protective effect of the environment mainly in three aspects:

First, there is no harm to metal mercury . LED lights inside unlike fluorescent lamps that use highly hazardous mercury , does not appear likely to leak mercury ions , like fluorescent light bulbs after a public hazard events or damaged during the manufacturing process .

Second, the manufacture of epoxy resins are organic polymers LED , after curing with good physical and chemical properties of the wafer , high metal adhesion strength , hard and flexible, and most of the saline solvent stable, not easily damaged even after aging can be damaged or recycling , environmental pollution is not formed .

Third, LED lamps and light particles display layout , are generally produced by scattering , rarely produce light pollution.

9,more cost savings

Compared to incandescent lamps, fluorescent lamps , LED lamps purchase price should be higher. However , due to the extremely low power consumption LED 's , in the long run can save a lot of electricity, you can save lamp replacement investment, and thus the cost of the integrated use of more cost-effective .

10,very low energy consumption

LED 's operating voltage is generally only 2 ~ 3.6V, operating current as long as 0.02 ~ 0.03A ie : electricity it consumes less than 0.1W, reducing energy consumption than the equivalent incandescent light efficiency more than 90 %, compared with energy-saving lamps reduced by more than 70%. Therefore, only the LED can be a real energy source !

led floodlight using floodlights way to make the building facade lights up, is one of the important ways to create and beautify the urban landscape . This illumination not only illuminate the facade of the building can also be designed by lighting designer to create more temptation than during the day touching effect , structured, emphasize and highlight the building 's personality.

led floodlight flexibility to choose the color temperature between 4000-7000K, imaging index up to 80 or more, more accessible luminaire natural light. led lamps light utilization is high, consistent with an angle of approximately 90% led emitting diode emitting angle with lighting , so most of the light fixtures direct exposure to a specific area , only a small part, through reflection , and therefore high efficiency light source . In addition there is no start-up delay led lights problem , they can always turn , for work , can be very easy to implement intelligent energy-saving control .

Characteristics of LED floodlights

Low current , LED floodlights temperature is not obvious . If the ambient temperature is high , LED floodlights dominant wavelength will redshift , brightness will decline , light uniformity , consistency worse. In particular, lattice , reliability , temperature stability of large screen LED floodlights for more significant . So thermal design is critical.

Production of materials

Light body material is aluminum alloy die casting surface treatment electrostatic spray coating temperature, anti-acid , anti-aging light body with light electrical integration design , compact structure, small reflector applications imported high purity aluminum , a variety of reflective surface design , with light to form a variety of different needs , high luminous efficiency, glare small light source can be customized according to customer needs, you can use the single-ended or double-ended metal halide or high pressure sodium lamp using E40 or RX7s mask is 5mm tempered glass, safe , high temperature, high strength , good transparency silicone rubber sealing strip of corrosion seals , sealing, waterproof , dustproof application of high performance ballast, ignitor and capacitor , to ensure that lighting electrical performance requirements in line with GB internal Lian line 1mm2PVC applied markers , stadiums , squares , trees , billboards , parking lots, building facades , etc.

Why choosing LED high bay light to replacement HQL lamps? Energy savings of up to 80% when replacing inefficient Mercury vapor lamps( HQL)

In past years, 400W HQL are widely used in industrial lighting in warehouse, supermarket, warehouses. But for todays industrial lighting, we can very easy to get a more energy saving lamp, especially LED lights. The LED high bay light is the best choice to replacement MH, HPS, HOQ, SON lamps. 

400W HOQ lamp usually consider to replacement by 100W LED high bay light, even the high brightness 400W MH, mostly could using 200W LED high bay light to retrofit. 

So looking for a reliable LED high bay light manufacturer is necessary before you make decision to replacement your traditional high bay lighting fixture. 

1.How long you can get back you invest?

2.LED high bay light quality, due ot LED high bay light consider to install in 4m higher, usually need lift when one lamp failed in work. That mean maintain cost very high.

3.Service: A good LED high bay light supplier or manufacturer could directly provide you lighting solution according to your project

4.After-sales service, LED high bay light with good quality usually can using 5-10years, but if a good service could help you in installation.

Why you can choosing TEK LED high bay lights?

5 reasons for your to choosing TEK LED high bay lights

1. All TEK LED high bay lights provide 3 years factory warranty

2. Good quality material, best heat dissipation designed heat sink, top-branded driver

3. TEKLED do not only provide LED high bay lights, but also provide lighting solution according to your project

4. Installation guide, IES file available for all items

5. 24Hrs technical supports

How can I replace Metal Halide high bay light?

Metal halide high bay lighting fixture is the leading source of industrial illumination, such as warehouse lighting, factory workshop lighting, shopping center, mining lighting, retail store, etc. They are very popular in both industrial and commercial in today’s word. 

All of us knows that metal halide high bay light is not cheap, sometimes even very expensive with some famous brand. The cost of electrical consumption, light bulbs, ballast, labor and often times lift fees can be very tolling to a businesses bottom line.

In the past few years most warehouse lights using Metal Halide high bay lighting fixture, the lifespan of metal halide usually consider to 20000hrs, but more than 50% failed or low lumen after 10000hrs, that means metal halide HID lamp becomes older and failed. 

In that case, the Metal halide lamp failed in work or low lumens, it is necessary to retrofit warehouse by new energy saving lights. LED lights,HID lamp, or CFL?

You may still consider about to replacement a MH bulb only. First we calculate how many watts a metal halide actual used.

Metal halide high bay lighting fixture power consumption also need to consider the ballast power consumption

        Total consumption = Metal Halide Bulb + Ballast 

Take 400W metal halide as example, actual cost for bulb + ballast equal to :

       400Watt MH bulb + 60Watt ballast = 460Watt

If you using 250Watt metal halide, the actual watt is 250+40=290Watt. 

No matter HID or CFL usually also need consider to ballast power consumption and life span can not compare with LED high bay light.

So LED high bay light is the best choice to replace a metal halide high bay lighting fixture. Usually 150W -200W LED high bay light more than enough to replacement 400W ( actual 460W) MH high bay lighting fixture. 

It is very easy to replacement, just move the older and failed MH high bay away from the hook, and install the high bay light directly, connect with the line, it’s done.

The LED light famous of long lifespan, so you do not need to consider for the maintain cost. Using other MH or HPS lamp you do not only need to consider the high cost for electric fees but also lift fees for maintain with bulb and ballast.

How to choosing the refelctors for LED high bay?

In current markets, there are three different bean angle reflectors available for choice, 45°90°120°. It is hard for factory or warehouse owner to choosing the LED high bay light reflector.

Here is a simple way to choosing the LED high bay light light reflector:

Illuminance & distance

45degree beam angle LED high bay reflector recommend to using in distance between lamp to floor 8-12m high, the narrow beam angle makes lighting focus, thus we can get a high level flux on the floor or platform.

90degree beam angle LED high bay reflector recommend to using in distance between lamp to floor 6-8m high.

120deg beam angle LED high bay light reflector recommend to using in a distance between lamp to floor of 4-6m high, the 120 degree reflector could increase a wide range of irradiation.

If you have a warehouse or factory want to retrofit HPS, MH high bay to LED high bay light, you can contact with your LED high bay supplier to provide you a simple solution. Big factory used to have engineer dould use Dialux provide a simulation according to your project.

 Customer or factory owner could according to your own project to select the suitable LED high bay lights.

TEK Lighting Technology Company Limited--China's leading manufacturer & supplier of industrial LED high bay warehouse lighting

Founded in 2008, we sepcialized in application of LED industrial & commercial lighting developing and manufacturing, products range including LED high bay light, warehouse LED corn light, LED corn bulb, LED flood light, LED pannel light and LED post top light.

Since 2008, TEK Lighting focus on retrofit 

TEK Lighting Technology Company Limited--China's first 3 years warranty LED high bay light manufacturer

Find good quality LED high bay light in China for your warehouse light?

Are you looking to replac old high bay lighting firxtures in a large warehous buiding with LED lights? 

Famous brand Cree, Osram, Philip price is very high? Why not directly contact with Chinese LED high bay light supplier?

LED high bay light save up to 70% energy compared with traditional HQL lamp high bay.

Provide up to 50000hrs lifespan, saving time and maitanance cost, usually if one high bay light failed, need to hire expensive access equipment when changing lamps.

Improve light quality in your warehouse, make it much easier to carry out tasks, and reducing production accident.

May be you have been heard China's products very poor quality, do you know more than 80% LED lights assembly in China? Most of the famus branded LED light OEM factories in China. Every markets have good quality products with reasonable price, it depents on you how to find out a reliable supplier.

As the China's first 3 years warranty LED high bay lighting factory, and China's leading industrial lighting manufacturer, all our LED high bay lights using high brightness BridgeLux LEDs, UL listed Meanwell Driver, and Super conductor heat dissipation as heat sink.

New Integrated LED high bay light

In Desember 2013, TEK Lighting lauches a new series Integrated LED high bay light. They have 120Watts to 300Watts LED high bay light available in this series, which designed to replacement 250Watt to 600W MH traditional bay lights.

The new designed integrated LED high bay make with waterproof and dust proof IP65 grade, suitable for use both indoor and outdoor applications.

Integrated LED high bay light heat sink use excellent quality aluminum, vacuum cavity of the thermal conduct, even one heat sink after more than 28 processes to make sure every piece of fin perfect connect with thermal cavity together, and whole heat sink connect without any screw and glue, in order to prevent the glue problem and fail down the heat sink hurt people.

Compare with the traditional extruded aluminum heat sink and conventional heat sink,the new integrated LED high bay light heat sink have advantage of lighter in weight, smaller in size, and cooling speed faster than 30%.

The integrated heat sink combined with vacuum heat pipe, the temperature will have a little rising when the constant temperature just begins, it will be stable in about half an hour, and temperature well contral in 60℃±3℃. Compare with other heat sink long time working will sharp increasing heat sink temperature, and the LED PCB temperature increased, it will be greatly increasing lumen decay, end LED high bay light life.

Acoording to Cree LED reports data shows, LED Tj>105℃， lifespan only a little longer than 10,000Hrs, LED Tj=95℃，LED lifespan>20,000hrs, LED Tj=75℃， LED lifespan>50,000hrs, LED Tj=65℃， LED lifespan>90,000hrs.

Also Lumiled LuxeonK2 LED droop cruve shows,

When LED Tj reach 115℃-135℃， LED lifespan will be reducing from 50,000hrs to 20,000hrs.

Then how to extend LED lifespan to extend LED high bay lifespan?
The keypoint is reducing the Junction temperature of LED high bay light.
How to reducing the LED juction temperature? The main point we need have a excellent heatsink which could release the LED heat fast.

TEKLED are adequately considered LED lifespan, and producing Integrated LED high bay light, well controlled the LED junction temperature in 60℃±3℃.

What are the performance advantages of LED high bay lights are?

LED high bay lights are energy saving lamps, because the superior design and cooling effect, by the majority of companies use. Particularly on mining. Following a brief LED mining lamp performance advantages: 

1 excellent explosion-proof performance, can be used in a variety of flammable and explosive safety 

2. imported chips, LED packaging structure optimized to achieve low light decay, high luminous efficiency, energy saving and environmental protection, etc.; 

The power supply key components used brand in the world, to ensure lamp life; 

4 using crystal lens with light, to meet the lighting needs of different occasions; 

5 using pass-through design, optimize cooling structure, ensure lamp life; 

6 lamps using angle locking device, to ensure long-term changes still occur angle in vibration environment; 

7 Light body with light alloy materials, special sealing and surface coating, to ensure that lighting in the humid, high temperature and other harsh environments never corrosion, rust;

8 pedestal variety of installation methods and boom type and so on. 

Use LED mining lamp field: the shipyards, mines, workshops, factories, warehouses, highway toll stations, gas stations, supermarkets, exhibition halls, stadiums and other places need industrial lighting. 

Advantage 

1 imported LED chips, high luminous flux, energy-saving effect is obvious, saving more than 70% compared with sodium. 

2 decorative effect is excellent, the appearance can choose a variety of colors, simple installation, easy disassembly, a wide range. 

3 lifetime high of more than 50,000 hours, longer than traditional light sources over 10 times. 

4 green pollution-free, no lead, mercury and other pollution elements, no environmental pollution. 

5 color is good, the physical color rendering more real. 

6 with built-in or CE / UL external power supply to use, safe and reliable, able to work in -30 degrees to + 55 degrees for 3 years. 

7 good heat dissipation.......

        LED High Bay Light with ordinary mining lamps have those advantages

   LED mining lamp using a fourth-generation light source, he more than other light sources, such as incandescent lamps, high pressure sodium lamp, high pressure mercury lamp, lamp has the following advantages: Voltage: LED mining light source using a low power, single voltage between 1.9-4V safer than the use of high voltage power supply.

  Effectiveness: High luminous efficiency, the current laboratory highest luminous efficiency has reached 161 lm / w (cree), is currently the highest light efficiency lighting products. Theoretically LED luminous efficiency per watt up to 370 LM / W, under the current chip structure in good condition without any change in the process so that every watt LED 150LM arrive without any problems, this brightness is reached, all the lighting in the area basically can be replaced. Expected in the next 1-3 years, LED light will reach 300 lumens per watt light efficiency. The US laboratory LED has reached 161 lumens of light per watt efficiency, total luminous flux 175 LM.

Shock resistance: LED is a solid-state light source, due to its specificity, with other lighting products can not be compared shock resistance. Stability: 100,000 hours, the light fades to the initial 70%

Response time: Response time LED lights nanosecond, is currently the fastest response time of all light products.

   Environmental protection: no metallic mercury and other harmful substances.

Color: LED fast fairly narrow band, the light color, color purity, non-variegated light, covering the entire band over the entire visible light, and can be a combination of R \ G \ B to anyone who wants to visible light.

Life: LED average life 5000-100000 hours, greatly reducing your maintenance and replacement costs. Found in the LED light source excellent characteristics, Guoguang Green started research and development of LED mining lamp, the light LED mining lamp uses Guoguang independent self-developed heat sink, better performance, light use international big LED chip packaging, CRI excellent (greater than 80 ), quality and security, and truly done and keep practical and beautiful.

  LED mining lamp suited for large-scale factories, warehouses, petrochemical, swimming pool, gymnasium, coal, iron ore, all kinds of mines. High Power LED Bay Light is currently on the market is the most excellent lighting, for more support, please call 150-1411-5394 Miss Yu.

How to cut your annual energy with LED high bay lights?

How to cut your annual energy by 50% or more with LED high bay lights?

How to reduce HPS high bay lighting cost by over 50% with LED high bay light?

In the past years, High pressure sodium(HPS) lamp is the leading source of industrial illumination many decades. We can see High pressure sodium(HPS) high bay light fixture installed everywhere which produced by Philips, Osram and...

In China, We can see HPS high bay used in factory, warehouse, shopping mall, gymnasium center. Some owners still do not realized the important of energy saving. Due to they do not know how much money they can save from lighting cost.

Currently, we handle with a warehouse with 89pcs 250Watt High pressure sodium(HPS) lamp high bay light fixtures., light on 16hours per day

How many wattages that 250W HPS high bay actual used?

250W High pressure sodium(HPS) lamp high bay light fixture actual use 290Watts

According to our customer’s project information, lux level request, we could use 80W LED high bay light with 90degree reflector to replacement 250W HPS high bay light fixtures.

How to calculate the watts?

It is very simple, just simply the number of high bay lighting fixtures multiplid by the number of power consumption for your lights. So we have 89pcs 250W HPS

89lights x 290watts=25810 Total watts =25.81KWh

How many watts cost per year?

Customer need to light on 16hrs/day, about 4000hrs/year, then total Kwh/year:

25.81Watt x 4000hrs per year=103204KWh

How to calculate the cost of lighting cost?

In view of the warehouse lighting consider to industrial lighting, cost much higher than home lighting, about US$0.2/KWh

103204KWh* 0.2= US$20640.8 per year

But use LED high bay light, cost US$5980.8 only. The life span of HPS consider to 4000-6000hrs, LED high bay light life more than 35000hrs.

So you can easy to cut your annual lighting cost more than 60% with LED high bay lights. Contact us now to get more information for LED high bay light retrofit HPS high bay light fixtures.

               Why LED high bay light reflector reasons to choose

LED High Bay Light It is a very long time to use its light, so we will save its energy requirements are relatively high. However, because of this we have to choose a great combination of reflectors. Its role in the reflector is actually used to gather the light as it is chosen the principle of parabolic surface design, it is possible to consume a very low light efficiency. LED high bay lights are usually apply a bead of high-power LED light source of light is called to do. When people choose reflectors can put it inside the hot gas discharge lamp and lower the temperature outside, to ensure that the cooling effect and the use of time LED mining lamp. Lights and electrical box cover book best fit to the divergence of heat and light protection. If the compact shape of the structure, which can reach a decorative effect. Indeed reflector for maximum effect is to make LED lighting can not reach such a fitting reflection, and soon raised the lamp usage, however, makes the irradiated material it presents even more real. Also have to make such an atmosphere environment to meet the requirements. Such reflectors can make the light softer eyes do not feel tired.

The most important thing is that the reflector material it uses, most normal state selected aluminum alloy, is taken to do the high-purity aluminum reflector, so that it will be more irradiated with light, the light will be evenly together, very effectively block the flash and glare, thereby protecting everyone's vision and can eliminate some of the problems brought about by the lighting color temperature is high. If you choose a secure production businesses, usually the state will observe the hood there any chemicals and substances composed of broken glass, so this can be more at ease consumer confidence. Consumers will also believe that the LED mining lamp energy saving and environmental protection is becoming increasingly important to see.

LED high bay light retrofit workshop lighting

In the past year, metal halide high bay lights widely used in industrial lighting in workshops, but in view of the high power consumption, most people consider to using LED lights to replacement MH bulbs as LED high bay to saving energy and money.

The workshop lighting usually consider to using 400W MH high bay before, in order to get a same brightness, customer need to use 150W -200W LED high bay light to retrofit existing 400W Metal Halide lighting in the workshop.

Normal workshop lighting need 300lux, the LED high bay light is the best choice for retrofit MH high bay in workshop as LED high bay lighting.

Retrofit your current 250W HPS lamp by 60W LED corn warehouse light in the Oil station.

In recent year, LED lights are widely used to retrofit HPS, MH, CFL, HID everywhere, they could used as LED warehouse light, LED gym light, LED street garden light, LED post top light, LED workshop light. But now, they also using in the oil lighting field. 

Current project, customer using 60W E40 base LED corn warehouse light to replacement 250W high pressure sodium lamp in the oil station. Saving more than 70% energy.

Retrofit workshop lighting by LED high bay light.

In the past years, 400w metal halide lamp high bay lighting fixture are widely used in industrial lighting in workshop and warehouses.

In this project, customer using Philips MH/U 400W metal halide high bay in the factory with 10meters high light system. Customer want to have same light quality as 400W metal halide lam at 10meter high to LED technology.

200W LED high bay light is the best choice to replacement 400W MH high bay in workshop lighting. 

Customers can get invest with new LED high bay light within 18 months The long life span of LED high bay light allow customer saving energy and money.

How to choose the right color temperature for your LED lights

Different places need different color temperature LED lighting, usually the LED lights consider to three colors, we call it warm white, nature white and cool white. LED lights for public applications to promote relaxation, people usually consider to choose the warm white which consider to 2800-3500K( K= Kelvin, Standard Unit for color temperature. And the cool white or nature white are usually consider to used to enhance concentration in office, workshop and repair Centre.

Some factory also producing CCT dimmable LED lights. The CCT dimming for LED technology is regarded as a difficult task. Usually consider set two types color temperature warm white and cool white into one LED lights, the power supply control system can freely to turn on the warm white color LEDs, or Cool white LED, and also turn on both cool white and warm white LED to get a nature color LED lights. 

The color temperature of LED lights consider to 1800K to 12000k, usually most LED lights consider to make CCT from 2800K-6700K, except some special applications as decoration or aquarium lighting, grow lighting.

How to choosing a right color temperature for your LED lighting products? 

Most people may asking:” What color temperature I should choose for my room, hotel, warehouse, jewelry shop, office? Should I have a certain color temperature?

Home LED lighting--Mostly home do not use cool color LED lights. Usually choosing warm color LED lights to built a warmer environment for home, color temperature consider to 2800-3500K in bed room, reading room use 4500-5500K, 

LED Building Lighting--Decorative LED lighting out of building use warm white or color LED flood light, red, green, yellow..., office and other places usually use cold white color LED lighting consider to 5500-6500K

Hotel LED lighting-- Lobby use cool white:5500-6500K, room use warm white:2800-3200K LED lights

LED warehouse lighting-- Warehouse Lighting usually consider to nature white (day white) 4000-5000K, or cool white 5500-6500K LED lights.

Industrial Plant LED lighting--Use nature white or cool white LED high bay lights.

Shipping mall LED lighting-- Use the cool white with CCT:6000-6500K.

Reference picture for LED lights color temperature:

                      Revolution of LED High Bay Light

Revolution of led high bay light , sounds very distant thing, but with the development of LED production technology , LED high bay light is bound to be a big change. However, there are certain factors LED high bay light restricted its development . First, the reliability of the LED high bay light products , cost and other issues ; Secondly, although in 2012 the global LED high bay light market is estimated at approximately $ 4.48 billion , but the country lacks competitive products , the lack of a number of patents, and international companies can not compete ; in addition, the end of the study to be used if the general lighting system equipment, higher brightness while generating heat phenomenon will follow , and the lack of testing and certification technology , the core problem is to choose , such as eutectic materials.

Major LED high bay light manufacturers continue to improve in the upstream technology, in order to maintain the brightness of the finished packaged in this technological innovation management tools, we can more clearly grasp the next 3-5 years, mainstream LED high bay light lighting industry , there are two main programs , namely the rational allocation of resources for innovation , to master the most optimal process parameters , becoming the LED high bay light LED Industrial technology Development bigger and stronger lighting industry provides a guide to action .

According to follow-up study of Chinese LED high bay light market , affected by the global financial crisis, the number of orders due to reduced growth is slowing down dramatically . On the other hand , due to the tight schedule export tasks , resulting in the growth rate is slowing down . Research type of equipment to complete production prototype commercial or LED high bay light backlight products , are rushing their territory, compiled working groups. Faced with this situation at home and abroad , TEK Lighting LED high bay light is based on its own , with quality as the core , high quality Bridgelux chip , the life of 50,000 hours ; on the other hand , faced a tight schedule , TEK Lighting is strictly comply with the delivery, the customer base and establish a good image.

LED lighting market to benefit not only the mining lamps and other lighting equipment , as well as domestic electronic information industry to take this opportunity to, have to develop , is designed to effectively phase out traditional lighting . Although , LED high bay light development by certain restrictions now, but the growth of market demand will drive its development.

Welcome to visit TEK LED flood light or Landscape LED flood light production line

In recent year,  LED flood light are widely use in so many applications, including swimming lighting, parking lot lighting, garden lighting, soccer fields lighting, building decoration lighting, wallwasher lighting, landscape lighting, etc. They are long-lasting and wide-rang color temperature light is easy to replacement traditional HPS, MH , Sodium flood lights

The LED flood lights also know as Landscale LED lighting or wallwasher lighting.TEK Lighting is the first manufacturer who producing 200W high power LED flood light to replacement 400W-450W MH lights. Heat-pipe is an efficient method for high heat flux removal from LED chip to Al heat sink.

LED lighting appear dangerous bottlenecks in the development 

It is reported that Shenzhen LED industry began in the early 1990s, the momentum together, showing the explosive growth of the industry, once occupied almost half of the country's LED industry. According to statistics, as of now, Shenzhen LED scale enterprise about 4000, the number of LED enterprises accounted for about 30%. Shenzhen is the largest LED packaging and LED display production base to base oriented electronics industry, the LED drive circuit design, intelligent optical design field strength, and more products with LED commercial lighting and public lighting based.

It is understood that, with respect to Foshan, Zhongshan and other lighting business gathering area, a large number of traditional lighting companies in Shenzhen slightly less, but it has a large number of small and medium enterprises in emerging lighting. It is reported that the face of industry difficulties, Shenzhen business prospects for LED lighting industry still have a very optimistic view, many companies on the market already has a very clear positioning and planning, which brought a whole piece of LED enterprises in Shenzhen region lively atmosphere.

2015, year of the crisis and machine coexist

From the business point of view gather, Shenzhen LED enterprises located in the upper reaches of the substrate material, epitaxial wafers, chip midstream, downstream packaging to all aspects of the application and supporting materials, processing and testing equipment, has formed a relatively complete industrial chain of domestic and In the downstream industry chain formed certain industrial agglomeration.

According to incomplete statistics, Shenzhen LED enterprises, enterprise applications, packaging companies, supporting enterprises accounted for about 33% of each epitaxial chips in the upstream business accounted for about l%. Which is still more than 99% of SMEs, and the majority of private enterprises, located in various aspects of the industry chain, and active promotion of private enterprise is precisely to ensure the Shenzhen LED industry sustained rapid development.

"2015, for the Shenzhen LED business, is a year of crisis and machine coexist." Tek Lighting Technology Limited Marketing Director, said, "Everyone on the LED increasing acceptance, as well as high-quality user products gradually raised certain requirements, and most of all to do foreign trade enterprises in Shenzhen itself, the quality of the product is very easy to meet domestic demand and cost-effective. "

"This year, the economic recovery of the domestic market for foreign trade enterprises in Shenzhen and strong, this is a good opportunity, but companies should exploit the advantages of a single product, like TEK lighting technology, has the advantage that the LED high bay and LED Corn Light, sales in foreign markets now, compared to the situation a little better, but again, if further reflect the product's price in the domestic market still popular. "

This year's Report, "two sessions" proposed by the Government, it is necessary to fight the new energy-saving environmental protection industry's pillar industries. From this perspective, the government is expected to energy saving and environmental protection efforts will increase, is bound to bring new market opportunities. Shenzhen Jiawei Solar Lighting Co., Ltd. is the energy-saving environmental protection industry in a typical. Shares ROCKETS Jiawei, vice president, said this: "This opportunity is not a blowout, a gradual growth, whether to seize this opportunity, to see business in the past few years, what had been done plenty of preparation and accumulation. "

Liu Xiong has been optimistic about prospects for the development of LED industry, because the development of the LED can reduce carbon emissions to meet energy saving requirements. He added that Shenzhen is a city of innovation, daring Ganpin Shenzhen enterprises have innovative features, and has been in the pursuit of change and innovation. "Through this opportunity Shenzhen enterprises and market environment unleashed, but seemed more promising." ROCKETS said.

Shenzhen LED business has its own advantages: First, the Shenzhen enterprises better overall product quality, there is a great advantage for the brand; second, the Shenzhen company has a technical advantage because Shenzhen is China's LED industry, foreign technology frontier, technology concentration the highest number of technology companies will set up R & D center in Shenzhen; third, Shenzhen has talent advantage, more focused R & D personnel, various professionals are relatively complete; fourth, Shenzhen LED enterprises regardless of upstream, midstream or downstream industries chain development have been very mature.

Based on these four major advantages, Shenzhen LED products enterprises should be "high, fine, sharp," to think from the perspective of creation, not just manufacturing. In addition, one of the biggest problems is the high cost of Shenzhen LED business, whether it is personnel costs or management costs, Shenzhen and other areas to be complementary resources, this is the next to go in Shenzhen LED business advantage.

Differences in development, optical design highlights

According to statistics, in 2014 the Shenzhen-scale electronic products manufacturing output reached 1.3829 trillion yuan, an increase of 10.9%. ? Shenzhen Most companies are doing electronic products, and LED lighting is an electronic lighting products, so Shenzhen enterprises in the grasp of electronic products stability, performance has a great advantage, especially in the light category products its special advantages.

"Shenzhen electronics industry developed making Shenzhen LED industry has a comparative advantage in circuit design, optical design of the product, in the light angle and more accurate understanding of other aspects of intelligence." The optical design is another big selling Shenzhen LED enterprises.

According to Chinese music, the Shenzhen enterprises mainly in LED lighting applications lamps, downlights, spotlights and other projects through the pipeline products, lighting products, in engineering applications, often simultaneously choose several different vendor products, each product requirements consistent interface standardization, enterprises in product design for the structure, electrical connections, optical design products and other aspects to consider more versatility and, therefore, inhibits the development of differentiation engineering products. "Shenzhen LED product design in favor of modular, intelligent, humane and other major features, the 'Pearl River' regional circulation class decorative products focus on different development is slightly different."

High dependence on exports, branding difficult

Although Shenzhen LED business has a unique foundation for the development, but there are still some bottlenecks. Shenzhen LED enterprises export to domestic sales is difficult, mainly in: First, a single channel Shenzhen enterprises, mostly for export and their invisible channels as the main marketing strategy, a lack of traditional channels; second, some companies mostly OEM, export to Lord, the lack of experience in the domestic market development, market development is not enough resources configuration; third, finished the enterprise ratio is not high, market limitations, sales channels have greater limitations; fourth, because the basic products of export enterprises positioning in the high-end, compared with the Zhongshan lamps no price advantage.

Domestic exports to the biggest bottleneck in the development of enterprises in Shenzhen LED

"Because most companies are Shenzhen factory-oriented enterprises, compared with the traditional lighting companies, domestic lighting applications market is not deep enough to understand; secondly, some companies do not combine specific environmental analysis of the product itself, for example, such a system of LED understanding of the product line also needs to be strengthened. "

Integration of resources, pushing complementary

In thousands of companies competing "Red Sea" market alone, all the real test of the strength of an enterprise. Chinese companies are accustomed to thinking "rather be beheaded, do Pteris" joint approach often too cold. But in the LED emerging markets, for many, only a "zero-based" SMEs, feeling the stones are sometimes not as good as the idea of ​​"giant" on the shoulder, it will take a lot less detours on the road to development.

Integration of resources from operational terms, it should be between enterprises in certain segments of the meticulous precision, by several influential business to co-ordinate the league to do business in Shenzhen. Some business alliances in the implementation process, because each business has its own needs, resulting in a process of cooperation can not hold an open attitude, making cooperation in the implementation of very BaoTuan limitations, there is not much action

According to the current market environment, ROCKETS believes should be set up by the relevant government departments alliances can be made responsible for this area to convene Kechuang Shenzhen Committee and other influential business alliance to do this, for each of the company's products making the layout of the re-positioning, it is a system that works.

I hope an open mind based on product characteristics and competitive enterprises out and has formed a certain scale, influential business associate to form complementary products, complementary market.

Conservative or aggressive, causing the industry heated debate

For Shenzhen LED business is to take a conservative or a radical question, the key to the strength of the enterprise itself and the development of the state, if the business itself is powerful, and its direction is very clear, and you can do some big action to promote, or do some promotional activities in the channel. For Shenzhen LED enterprises, it belongs to the type of manufacturing, it would have to be cautious about the domestic market.

"First of all on the domestic market have their own understanding, and secondly put their own advantages and disadvantages of it, in the end is going to win in a single product, or to focus on a certain segments." Ouyang Zhicheng believe that this is the Shenzhen lighting companies today need to think about the topic.

If the single from the conservative or aggressive angle to determine Shenzhen LED business, which is incorrect.

From the current point of view of the market environment, look at the global, in fact, overseas markets such as Europe, America, Japan and South Korea is still very active, and for export-oriented enterprises and overseas have certain channels and market infrastructure, and this year their orders is still very abundant. We can clearly feel they have signs of increased investment, this investment is multifaceted, new product development, recruitment, including overseas markets increased, from this perspective, there may be some new inputs compared to the past two years will be more.

I TEK-LED High Bay Light, I speak for himself

You just saw my price, I did not see quality; you have your choice, I have my stick; you deny me now, I decided I market; you laugh at me unworthy durable enough to illuminate the shop I pity you look shallow; you can despise me thermal performance, I will prove who is this era of lighting. High is destined to travel a lonely road and ultimately cast aside and questioned, but, so what? Even not being optimistic, we must continue to illuminate the world. I TEK-LED High Bay Light, I speak for himself

TEK take you into the world of LED floodlights

No contact with lighting floodlights friend must first heard. He is what shape, what kind of lighting effects, knew nothing about. Here TEK-LED with you to understand what is LED floodlights.

Taken literally, in floodlight LED floodlight is on the LED light source applications.

Speaking LED floodlight, we must first understand what is under the floodlights. Floodlights and ordinary point light source is different, it is a kind of energy in all directions uniformly illuminated points of light. Its light will appear as an icon octahedron in the scene. Floodlights illuminated area can be adjusted, this feature is widely used, in effect, allowed the production. Flood is the English name Floodlight. LED floodlight LED lamp beads as the light source is a floodlight. It has all the characteristics of LED lamps, lighting effect is a good source.

LED floodlight beam produced highly diffuse, no direction, vague outline characteristics. This shadow beam produced is transparent, illuminated silent, the speed of light and the general weakening of the spotlight is very slow compared to. It looks like a LED floodlight unshaded light.

Greatly affected by the temperature of the LED floodlights

Generally smaller current, LED floodlights temperature rise is not obvious. But if the environment is stable up to a certain extent, the dominant wavelength LED floodlights will redshift, brightness is reduced, light uniformity deteriorates. Thus reduced stability. So when the LED floodlight applications thermal design must be safe and reliable.

LED floodlight features and advantages of a simple analysis:

1, LED floodlight usually high purity aluminum as a reflector, so the beam is very accurate reflection effect is very good.

2, floodlight bulb replacement back open design, maintenance is very convenient.

3, symmetrical narrow-angle, wide-angle and optical systems with asymmetric.

4, in order to facilitate adjustment of the irradiation angle, LED floodlights are generally designed with a scale plate

5, energy saving, high stability, long life, recyclable.

LED lamps popularity, make our lives more comfortable and safe. LED floodlights are widely used in commercial lighting, landscape lighting, road lighting, our lives can be seen everywhere: such as street lighting, stadium lighting, concert lighting and so on.

 Can you provide simulation to study which LED high bay lights suitable for my project?

Yes, we can provide silumation reports to you for your project. Pls provide us your current project information as below:

1.Where Will you attempting to use LED high bay light?

For example: Using LED high bay light in sport center, warehouse, workshop, etc.

2. Length:__(meters/ inches)

3. Width:__(meters/ inches)

4. Room Height:__(meters/ inches)

5. Installation Height:__(meters/ inches)

6. What is the current lighting fixture? Wattage?

7. How many conventional high bays in this room?

8. What is the distance between lamp to lamp?

LED bay light use

LED mining lamps, applied to different places also called other names, such as when used in high-bay plant, called the high-bay, with call fresh light at the food market supermarket. LED High Bay Light, is to replace traditional incandescent lamps, sodium lamps, energy-saving light bulbs, with high brightness, light is small, long life, no mercury, no UV, less heat, light weight, low-maintenance and many other features, It is a real sense of environmental protection, safety products, energy and money.

Source: The new bright LED Bridgelux chip, the life of 50,000 hours, environmental protection and efficient, non-toxic and non-UV; color and white LED fluorescent lamp color temperature can be customized according to customer requirements, the white color rendering index greater than 80.

Housing: aluminum shell, chip radiator, good thermal conductivity, coupled cooling fan so the LED junction temperature below 50 ℃, ensure the LED can work long hours without over-temperature, light is small; compact appearance beautiful, light weight.

Lamp drive: A new high-power and efficient circuit design, power factor up to 99%, the highest efficiency can be up to 93% over-temperature protection, overvoltage protection, overcurrent protection, short circuit protection, reliable, and efficient energy saving.

The main application areas: applied explosive gas atmospheres and high bay lighting. Such as: Coal plants, oil plants, chemical plants, warehouses, shopping malls, high-bay plants, food market, etc.

Want to know more parameters of products, welcome to TEK-LED advice!

What lighting tunnel for it!

Tunnel suitable for LED Flood Light: Because the tunnel lighting is different from ordinary road lighting, tunnel was a block of space, natural light can not shine in which, in order to ensure driving and vehicular connectivity of life and peace, even the whole day inside also needs artificial lighting, tunnel lighting is an integral part of the tunnel to establish local. Particularity of automobile exhaust, noise, vibration, pure air, corrosive gases, moisture and other harsh environment posed tunnel lighting, the need for full consideration of communication vehicles and pedestrians a safe warm lighting environment. So LED Flood Light is suitable for tunnel!

LED corn warehouse light bulb for interior lighting in Australia

The project for interior lighting of a store in Australia. Our customer using LED bulb to replacement existing store lighting. They used Osram 150W powerstar HQI-E, 11000lm, E27 base in current lighting fixture.

Before:

HQI-E Osram 150W MH bulb, E27 base

From the picture, you can see one high brightness light in the high bay, it is our customer try sample to testing our LED corn light. They very satisfact on the LED corn light and retrofit all the MH bulb to our LED corn lights now!

From the picture, you can see one high brightness light in the high bay, it is our customer try sample to testing our LED corn light. They very satisfact on the LED corn light and retrofit all the MH bulb to our LED corn lights now!

E27 BASE 60W LED corn light, CRI>75, Flux>6600lm--Now!!

No matter you want to retrofit MH high bay warehouse light or post top HPS garden street lighting, contact us now to get more information for the retrofit LED lighting today. 

Retrofit factory lighting solution--180Watt LED High Bay Light retrofit 400Watt Metal Halide High Bay Light

Customer using Philip 400Watt flood light in the machining factory before, the machining workshop working days of 24 consecutive hours everyday. The factory owner want to find a energy saving solution to release from a consistently high electric bill.

In this project, total have 52pcs 400Watt Philip flood lights, and 96PCS 400Watt metal halide high bay light. 

How many watts consume for the machining factory with traditional 400Watt MH ? 

Total:852.48 kWh/day; 18754kWh/month

Total Annual Cost To Operate:US$65753

180W LED high bay light could replacement 400Watt MH high bay

200W LED flood light could retrofit Philip 400Watt Metal Halide flood light.

How many watts consume for the machining factory with new LED lights ? 

Total:341kWh/day; 7503kWh/month

Total Annual Cost To Operate:US$22508

LED light saving 60% energy than conventional 400Watt MH; Total LED Savings Annually US$43245

If you want to have a lighting solution for your own project, pls visit our website: www.ledcornbulbs.com to contact us.

TEK LED floodlight with LED lamps you identify

1. The floodlight is not the case with special needs, in the home or small rally was not used because the high-power lighting devices after some waste.

2. The first difference and distinction floodlights cast light lamps, lamps for light rays hit the requirement is to make the place, no place can not illuminate, like a large spotlight - that is professional cast light Light emitting angle is small, irradiation distance, distance per unit area with high illumination; and floodlights requires large areas of light scattering light, like the sun, a professional that is light angle, irradiation distance is short, the same distance per unit area Compared to cast light illumination is low.

3. floodlights as in the power of small, still easy to carry, like the construction industry, able to use rollers to connect wires to faraway places to give lighting. Like 10W, 30W of LED floodlights, in a small town with a very universal, temple or fair, direct planes to take a high power on the line, as long as it does not rain.

4. When it comes to rain, we should pay attention to when purchasing a waterproofing, silicone ring under glass is invisible, but you can check the glass and die-cast aluminum joints below is stable, if there is an uneven joints or then discarded. Then check the waterproof connector is solid, whether there is a gap when moving around the wire and the like. And shake the box to listen to whether there are sound power, if the power supply is not fixed.

5. Next, check for fingerprints and debris if it is a more serious problem LED on the reflector.

6. Can I see another side to see the positive and negative LED cable, this is generally not see, unless there is a problem structure. As can be seen how the joints.

7. If the professional point, you can ask the store for a distribution curve, temperature and the like. After working long hours can manually test the surface temperature, and the temperature contrast different regions. Short, temperature should be very low, especially 10W / 30W such relatively small power.

8. Any questions can TEK-LED Consulting Jenny.

What wattage LED corn bulb could replacement 150Watt Metal Halide?

Lets's study from a shop lighting project in Australia

They used Osram HQI-E 150Watt metal halide before.

We can see from the Osram specification, 150Watt luminous flux up to 11,500lumens

What wattage LED we can use? 50Watt.

so he purchased one sample 80W LED corn light with 6000Kelvin to test.

from the picture you can see, 80Watt LED install on the right, We can see the price $11.35 on the price lable clearly. But another side below the MH bulb, FEVER. NICE?it is a little difficult to see the words, Nice...?

Obviously 80W LED corn light much more bright than metal halide.

so they retrofit 150Watt Metal Halide by 60W LED bulb.

Now we can see the goods display on the shelf clearly.

For more LED corn bulbs information, please visit our website: www.ledcornbulbs.com

What wattage LED corn bulb could replacement 200Watt Metal Halide?

To allow research from a supermarket lighting project in Australia

They used Osram HQI-E 150Watt metal halide before.

We can see from the Osram specification, 200Watt luminous flux up to 11,500lumens

What wattage LED we can use? 50Watt.

so he purchased one sample 100W LED corn light with 6000Kelvin to test.

from the picture you can see, 100Watt LED install on the right, We can see the price $11.35 on the price lable clearly. But another side below the MH bulb, FEVER. NICE?it is a little difficult to see the words, Nice...?

Obviously 100W LED corn light much more bright than metal halide.

so they retrofit 200Watt Metal Halide by 80W LED bulb.

Now we can see the goods display on the shelf clearly.

For more LED corn bulbs information, please visit our website: www.ledcornbulbs.com

LED high bay light- The best lighting solution for high ceiling application.

The principle of heat dissipation for TEK LED high bay light-- High performance heat pipe with aluminum fins.

The heat-pipe’s principle is using the quick phases change the liquid（medium) under vacuum condition which exchange the heat, the heat transfer rate is superior to any metal.By Riveting the heat pipe to the aluminum fins, the heat pipe can conduct heat rapidly from chips bottom to the fins, greatly lower down the temperature of LED light source, extending it’s lifespan

Why use heat pipe designed heat sink for LED high bay light?

Before that, we study the thermal management of high-power LEDs. Most of the electricity in an LED becomes heat rather than light, high power LED transforms 20%-30% of electric energy to light and more than 70% of electric energy has been transformed into heat. Moreover, if use a build-in driver, the wastage of driver also adds the heat of LED. The accumulation of heat makes the temperature rise, the rising of temperature cause the performance of chip decay, material ageing, and degeneration. If this heat is not removed, the LED run at high temperatures, which not only lower their efficiency, but also makes the LED less reliable. Thus, thermal management of high power LEDs is a crucial area of research and development. It is highly necessary to keep the junction temperature below 120degree to run the LED’s maximum lifetime. This is largely due to improved thermal management and heat sinking characteristics

LED chip junction temperature is how to produce the

LED fever because of the added power did not completely converted to light, but is part of the conversion into heat. LED light efficiency is currently only 100lm / W, its electro-optical conversion efficiency of only about 20 to 30%. That is about 70% of the electrical energy into heat energy.

Specifically, LED junction temperature is due to two factors caused.

1. The internal quantum efficiency is not high, that is when the electrons and holes recombine and generate photons are not 100%, commonly referred to as the "current leakage" leaving the PN zone carrier recombination rate decreases. Leakage current times voltage is this part of the power, which is converted into heat, but this part does not account for the main component, because the internal photon efficiency is close to 90%.

2. internally generated photons emitted to the outside of the chip can not be fully and finally into heat, which is the main part, because the current is called an external quantum efficiency of only about 30%, most of them converted to heat up.

While incandescent light efficiency is very low, only 15lm / W or so, but it is almost all of the electrical energy into light energy and radiate out, because most of the radiant energy is infrared, so low light efficiency, but eliminating the problem of heat dissipation.

Cooling LED is now more and more people pay attention, because the LED light decline, or life is directly related to its junction temperature, heat is not good junction temperature is high, life expectancy is short.

High-power LED white LED chip cooling applications and solutions

Today white LED products are increasingly used in various fields and put into use, people feel the amazing power LED white light brings pleasure but also practical issues to worry about its existence!

First, from the very nature of high-power LED white light. High-power LED luminous uniformity there still poor, closed material life is not long, especially its LED chip cooling problem is difficult to be a good solution, but can not play the advantages of white LED applications are expected.

Second, from the market price for the white power LED. In high power LED or an aristocratic white products, high-power products because the price is still too high, and technically still need to be improved, so that high-power white LED products are not who wants to use it can be used. Here OFweek semiconductor lighting network to break down under high-power LED heat-related issues in.

In recent years the efforts of industry experts, high-power LED chip cooling problems made the following points to improve the program:

1. to increase the amount of light emitted by the LED chip to improve the area.

2. Using a number of small area LED chip package.

3. Change the LED packaging materials and fluorescent materials.

It is not by the above three methods can be fully improved heat dissipation problem of high-power LED white light out? Actually striking! First we though the LED chip area increases, in order to obtain more flux through the inner (light unit time the number of beams is the luminous flux per unit area, the unit ml) white hope to achieve the desired effect, but because the actual area is too large, which led to the emergence of some of the counterproductive phenomena in the application process and structure.

It is not white high-power LED heat dissipation problem really can not solve it? Of course not impossible to solve. Simply increasing the chip area for the emergence of negative issues, LED white light industry according to the design of improved electrode structure and flip chip packaging structure and use of a number of small area of ​​the LED chip and other ways to improve high-power LED from the wafer surface so as to achieve 60lm / W High Low High heat flux luminous efficiency.

In fact, there is a way to effectively improve the heat dissipation problem of high-power LED chips. That is to replace the previous white plastic packaging materials or plexiglass with silicone. Replace the packaging materials not only can solve the heat problem LED chip white LED life can be improved more, really double-edged sword ah. I would say that almost all high-power LED white light such as high-power white LED products are silicone resin as a sealing material should be used. Why are high-power LED must be used as a packaging material silicone? Silicone on the same wavelength as the light absorption rate of less than 1%. However, the absorption rate of the epoxy resin to light 400-459nm of up to 45%, easily absorbed due to the long aging produced after this short wavelength light leaving the light fades serious.

Of course there will be a lot of problems such as high-power white LED chip cooling in actual production and life, because the more people on a wide range of high-power white LED applications will be more in-depth intractable problems!

LED chip is characterized by an extremely high heat in a very small volume. The LED itself thermal capacity is small, it must be the fastest to the heat conduction out, otherwise you will have a very high junction temperature. In order to maximize the heat to outside the chip, people in the LED chip structure has been a lot of improvements. To improve heat dissipation LED chip itself, its most important improvement is the use of better thermal conductivity of the substrate material. Like Cree's LED thermal resistance because the use of silicon carbide as the substrate, the thermal resistance than other companies at least twice as low.

Even if it can resolve from the wafer to the heat resistance between the encapsulating material, but the cooling effect from the package to the PCB is not good, it is also resulting in LED wafer temperature rises, the phenomenon appears luminous efficiency decreases. So, like the Panasonic just to solve this problem, starting in 2005, it gave, including circular, linear, surface type white LED, and PCB board design into one, to overcome possible because of the emergence from the package to the PCB board between thermal disruptions.

Thus, in the face of the continuous improvement of the current situation at the same time, how to increase the heat resistance, but also at this stage of urgent problems to be overcome, in every sense, in addition to the material itself, but also including inter-material from the wafer to the package heat resistance, heat resistance thermal structures, packaging material between the PCB board, thermal structure, and the PCB thermal structure, all of which needs to be holistic considerations.

LED lighting cooling Questions

The current common incandescent bulbs or fluorescent lamps, even if the product itself is running may produce heat, but heat components can still be effectively isolated, light source and power connection seat will not produce heat and unexpected problems. But solid-state lighting is different, the one LED module on the running temperature of a single point, must take more active means of heat treatment, heat treatment simultaneously with active and effective mechanism in order to avoid a problem with the lamp. LED solid-state light heat treatment problem is much complicated than traditional lighting.

Or more than a traditional light fixtures generate heat during operation issues, such as halogen bulbs or incandescent bulbs, if incandescent form, that is heated in a tungsten lamp ball special treatment produces light.

In fact, rather than the high temperature generated in the filament lamp holder, lamp holder even due to light ball glass or metal tungsten light by the radiant heat, the heat conduction indirect high heat, but the temperature resulting in acceptable safety range, then With non-direct contact conduction, security is relatively high.

But replaced with LED solid state light source in the form of lamps, the treatment will likely become a new application security issues. Most people would think that LED with high energy conversion efficiency, low driving energy resources, natural use of high security, but in fact LED solid-state light source in order to achieve the purpose of the daily lighting of the application must be strengthened to increase the power unit through a single set of components lumen output elements, such as lighting plant will take the form of strengthening the integration of multiple LED component output, and multi-component running also improves LED solid-state light source type deflection point source problems, so LED solid-state lighting technologies can produce light such as light bulbs like surface lighting effects.

If you want to strengthen the lumen output unit members must be higher current to the LED chip PN junction produce more lumens, but higher currents also make single-point temperature LED components increases, more difficult to handle, even for improve the performance of light type, luminous efficiency lamps and adopt a multi-component and form, but also make high-temperature LED lighting intensifies the problem, so that the heat problem more difficult to handle.

Looking at the current development trend of LED lighting market, most LED light source manufacturers would most likely be market-driven, because of the high price, high profits, it can quickly enter through the development of the technical differences between the more avant-garde technology LED light source market, for example, for upholstery, situational lighting applications embedded lights, wall lamps, ceiling LED light fixtures became more common form of design, power efficiency to replace traditional lamps after its also the most relevant industry attention.

Thermal management design LED light fixtures must focus on process, where possible in a closed or semi-dense dead through the use of recessed lights, wall lamps, ceiling products, a more demanding challenge, lamps developers have from the material, product configuration, the main / passive cooling mechanism, drive chip design and other aspects to invest more resources in order to avoid the products in question Hajime students. LED Recessed Lighting especially small and often adopt a multi-component integration, high thermal design difficulty module. Recessed Lighting shell is aluminum extrusion or heat sink design, can play the role of autologous heat. But this is not enough.

LED thermal management: NTC maintain continuous operating temperature LED lights use safety

If the LED lamp does not come with sufficient thermal management design, during use may cause high fever running lamps because often caused by the sharp drop in life expectancy, resulting in frequent replacement of a defective LED lamps have problems, severe cases may even lead to accidents due to high temperature operation causing lines or the surrounding décor is burning!

In the product development stage, you can use intelligent LED lighting control technology, see temperature performance LED lamps with integral light source modules through active monitoring, simplify thermal management device, and when the temperature rises to the lamp and the surrounding zone, the Lamps must reduce electric power, reducing LED light output, in order to enhance the use of LED solid-state light fixtures security.

LED Ceiling housing considered as relatively simple design form, if the lamp itself using a drive that features a more focus on power conversion and LED component drivers, did not embedded microprocessor and heat treatment temperature control module, in order to avoid increasing the product raw material pieces cost, LED lamps can be integrated NTC (NegativeTemperatureCoeffient) negative temperature coefficient ThermistorSensors electricity, is the relatively high cost-effective security design.

The so-called NTC electricity, its purpose is to be set back by electronic monitoring modules LED lamps temperature, through default temperature warning or automatic processing of the corresponding driving condition, taken off the LED solid-state light source module on ways to increase the use of safety LED lamps while NTC electricity also reduces the complexity of the design.

Since the temperature coefficient of electrical NTC very large, it can detect small changes in temperature performance that is widely used measurement needs, control-related electrical design and compensate for temperature, whereas NTC electrical LED light source module design, basic Product ambient temperature changes in the measurement of solid-state LED light fixtures, as measured with the voltage situation will change in the status of NTC, directly measured the electrical voltage and NTC temperature correspondence.

When the NTC and peripheral level or raise the temperature of the entire module, NTC electrical resistance then decreases, products can be so dependent relationship feedback control mechanisms related to security, such as reducing the LED light assembly drive current or direct forced off lighting, luminaire temperature problems improve after automatic reply lighting state, thereby obtaining safety lamp used.

LED lamps can import temperature monitoring microcontroller mining SMD components manufactured in the form of NTCTHERMISTOR

Improved form of the aforementioned NTC electricity, if you want to achieve a better design, with a more sophisticated security MCU design is a relatively pragmatic approach in the development project, the status area may be divided into light LED light source module is normal, lighting It is turned off, with the temperature warning and temperature measurement of program logic to construct a more perfect wisdom lighting management mechanism.

For example, if there is a temperature warning lamp, the temperature measurement module that is still acceptable temperature range can be maintained in the normal way, through natural dissipation of heat sink operating temperature; and when the warning told the measured temperature has reached the required implementation of active cooling reference mechanism, then the MCU must control the cooling fan for moving, even when the temperature reaches the value, the system must be directly off the drive power supply through the MCU, LED components temporarily stop operating, natural heat dissipation process.

Determine whether to use the lamp on or off, using a simple judgment bit to do with the understanding of the product changes the current status, the more critical part of the temperature measurement, the temperature must be measured in real-time and reference table system for comparison to confirm the current normal or abnormal state level module calculates the temperature of the pitch, the automatic temperature control corresponding to be managed.

Similarly, when the temperature enters block, control mechanisms should immediately turn off the light source, while the system is shut down after 60 seconds or 180 seconds after the temperature again to confirm until the LED solid-state light source module temperature reaches normal, then re-driven LED light source, continue to provide illumination.

LED floodlights working principle and characteristics

1.Works ：Floodlight is in effect, making them the most widely used of a light source, standard floodlights used to illuminate the entire scene. Scenario can be applied to multiple floodlights to produce good results. Floodlight is, in effect, the most widely used of a light source, scene floodlights can be more coordination role in the birth of good results.

2. Use of premises

The façade, plaza night, landscape lighting, interior decoration, architectural lighting, outdoor advertising, and so on .....

LED floodlight features：What is LED floodlight it is mainly used for architectural lighting purposes, as well as commercial space lighting, decorative ingredients heavier, its appearance also have well-rounded, because the general had reason to consider the heat and therefore its shape with the traditional cast light there are some differences.

LED floodlights there is also a led lamp cup formed. He had some of their characteristics.

1, high purity aluminum reflector, beam the most accurate reflection the best results.

2, symmetrical narrow-angle, wide-angle and optical systems with asymmetric.

3, behind the open-type lamp replacement, easy maintenance.

4. The lamps are easy to adjust with scale plate illumination angle.

LED lights advantages:

1, features LED lights themselves - one-way, no light diffuse light and ensure the efficiency of light.

2, LED lights have a unique optical design, LED lights will light shines on the desired area lighting, and further improve the efficiency of light in order to save energy.

 3, light is small, light failure a year less than 3%, with 10 years still reached the road use illumination requirements, and high-pressure sodium light fades large, about a year has fallen by more than 30%, therefore, LED lights in the use of power the design can be lower than the high pressure sodium lamps.

4, LED lights with automatic control energy-saving devices, can be implemented in time to meet the lighting requirements of different circumstances the maximum possible reduction in power and save energy.

 5, LED are low voltage, single LED drive voltage is safe voltage, series single LED power is 1 watt, so it is a more secure than the use of high voltage power supply, especially for public places (for example: street lighting, industrial lighting, automotive lighting, commercial lighting, etc.).

6, long life: can be used for more than 50,000 hours, five-year quality assurance.

7, high luminous efficiency: using ≥120LM more chips, as opposed to traditional high pressure sodium lamp can save more than 75%.

 8, installation is simple: no Jiamai cable without rectifiers, etc., directly to the street light poles installed in or connected to the light source lamp shell original nest.

 9, quality and reliability: power supply circuit used in all high-quality components, each LED has a separate over-current protection, without fear of damage.

10, light color uniform: without lens, not to increase the brightness at the expense of uniform light color, so as to ensure no aperture light color uniform.

 11, LED does not contain harmful metal mercury, unlike high pressure sodium or metal halide lamps at end of life damage to the environment.

LED lights with conventional high pressure sodium lamps is different, high-power LED street lamp light source using low voltage DC power supply, power-type GaN-based blue LED with yellow phosphor synthesis of highly efficient white LED, high efficiency, safety, energy saving, environmental protection, long life fast response, unique advantages of high color rendering index, can be widely used in urban road lighting. Housing available PC pipe production, high temperature of 135 degrees, low temperature up to -45 degrees.

If you are interested in LED lights to contact us!

Contact Person: Jenny Wei  http://www.ledcornbulbs.com/

LED lights advantages:

1, features LED lights themselves - one-way, no light diffuse light and ensure the efficiency of light.

2, LED lights have a unique optical design, LED lights will light shines on the desired area lighting, and further improve the efficiency of light in order to save energy.

 3, light is small, light failure a year less than 3%, with 10 years still reached the road use illumination requirements, and high-pressure sodium light fades large, about a year has fallen by more than 30%, therefore, LED lights in the use of power the design can be lower than the high pressure sodium lamps.

4, LED lights with automatic control energy-saving devices, can be implemented in time to meet the lighting requirements of different circumstances the maximum possible reduction in power and save energy.

 5, LED are low voltage, single LED drive voltage is safe voltage, series single LED power is 1 watt, so it is a more secure than the use of high voltage power supply, especially for public places (for example: street lighting, industrial lighting, automotive lighting, commercial lighting, etc.).

6, long life: can be used for more than 50,000 hours, five-year quality assurance.

7, high luminous efficiency: using ≥120LM more chips, as opposed to traditional high pressure sodium lamp can save more than 75%.

 8, installation is simple: no Jiamai cable without rectifiers, etc., directly to the street light poles installed in or connected to the light source lamp shell original nest.

 9, quality and reliability: power supply circuit used in all high-quality components, each LED has a separate over-current protection, without fear of damage.

10, light color uniform: without lens, not to increase the brightness at the expense of uniform light color, so as to ensure no aperture light color uniform.

 11, LED does not contain harmful metal mercury, unlike high pressure sodium or metal halide lamps at end of life damage to the environment.

LED lights with conventional high pressure sodium lamps is different, high-power LED street lamp light source using low voltage DC power supply, power-type GaN-based blue LED with yellow phosphor synthesis of highly efficient white LED, high efficiency, safety, energy saving, environmental protection, long life fast response, unique advantages of high color rendering index, can be widely used in urban road lighting. Housing available PC pipe production, high temperature of 135 degrees, low temperature up to -45 degrees.

If you are interested in LED lights to contact us!

Contact Person: Jenny Wei  http://www.ledcornbulbs.com/

Comparison of LED lights with ordinary lights

    LED lights and ordinary street comparison in the following areas:

    1, electricity comparison:

    Use 60W LED lights produce electricity a year, using only ordinary 250W high pressure sodium lamps produce 20% of electricity a year, saving electricity costs, it is the ideal energy-saving products, but also conform to the construction of a conservation-oriented society trend.

    2, the laying of cost comparison

    LED street light power is 1/4, the laying of copper cable cross-sectional area required for ordinary high pressure sodium lamps require only ordinary street 1/3, saving a lot of laying charges.

    Based on the above two cost savings, the use of LED lights over the use of ordinary high-pressure sodium lamps, the former owner can recover the initial investment cost increase in a year.

    3, illumination contrast:

    Use LED 60W up to 250W high pressure sodium street light illumination, greatly reducing the use of power; LED lights because of the use of low power, it can be combined with wind energy, solar energy, used on city roads.

    4, temperature contrast

    Than the ordinary lamps, LED lights temperature generated in the course of low, continuous use does not produce heat, no burning lamp black is not black.

    5, safety performance comparison

    Currently on the market cold cathode lamp, lamp, are very excited by the X-ray high-voltage spot lighting, contain harmful metals such as mercury, and harmful radiation; contrast, LED lights are safe low-voltage products, installation and use of process greatly reduces security risks.

    6, environmental performance comparison

    Ordinary street containing harmful metals, spectra contain harmful rays. In contrast, LED lights spectral purity, free of infrared and ultraviolet light, no radiation, no light pollution, and does not contain hazardous metal waste recycled, typical of the green lighting products.

    7, life and quality comparison

The average life of an ordinary street lamp is 12,000 hours, replace street lights is not only costly, but also affect transportation, construction and other places, especially in tunnels inconvenience; the average life expectancy of 100,000 hours of LED lights, use 10 hours per day, the service life of up to ten years above, once and for all. In addition, LED lights waterproof, impact resistance, shock resistance are good, stable quality, in the case of maintenance-free product shelf life.

If you are interested in LED lights to contact us!

Contact Person: Jenny Wei  http://www.ledcornbulbs.com/

          LED HIGH BAY LIGHT USED IN Germany

One of our customer in Germany use 150W LED high bay light with 90 degree reflector, AC85-277V. 

What wattage LED high bay light used in above project? 150Watt, the customer use 150W LED hi bay lights in 2013, till now, LED hi bay lights working well. 

Related products:

http://www.ledcornbulbs.com/150W-LED-HIGH-BAY-LIGHTS.html

80W LED Corn Light replace 150W MH bulb high bay lighting fixture

In this project, customer use 150W metal halide industrial high bay light with 45degree polycarbonate reflector before in the shopping mall.

The customer want to get a higher illumination on the current shopping mall, they choosing 80W LED corn light to test. 80W LED corn light lumen out put up to 9600lm. The customer is very happy and satisfied with LED corn light sample. 

Pls see picture below:

LED corn light lumen out put more than 120lm/Watt, the best solution for industrial high ceiling bay lights to replacement conventional Metal Halide lamp, High Pressure Sodiim Lamp, and CFL bulbs.  Standard Edison E27 and E40 Base. Easy installation, no need replace old lighting fixture.

Get more information about LED corn light, pls contact: Sales@ledcornbulbs.com.

60W LED CORN LIGHT REPLACE 150W MH IN SHOPPING MALL

In this project, customer use industrial high bay lighting fixtures with 150W metal halide bulbs in the shopping mall. The owner want to improve the lux level for this shopping center, and want to change to use a energy saving lights. LED high bay in his consideration at first. The shipping cost of LED high bay light is very high, we recommend using LED corn light more than enough to retrofit existing 150W metal halide bulb, easy installation and cost less than use LED high bay lights.

60W LED corn light, Epistar 2835 SMD LED, lamp lumen output up to  120lm/Watt ( @CRI70), standard E27 base, could directly screw into current lamp holder, do not need to retrofit whole lighting fixuture, usually customer could get back invest for retrofit new LED corn lights whthin 12 months.

Any questions about LED corn lights, pls contact us sales@ledcornbulbs.com.

TEK street lamp cover advantages

1, the appearance of simple, stylish and beautiful.

2, high quality die-cast aluminum design street thick shell, thermal structure and light shell integration design, and serrated flaky fin can effectively improve the heat dissipation; superior heat on both sides of the intermediate structure, plays a uniform cooling effect, so the whole street is more stable during use.

2, power supply built, more beautiful, more stable and secure

3, the outer surface of the rigid heat radiation material electrostatic spraying, the housing having an excellent heat dissipation, corrosion wear; with superior stability, not powder, do not fade, the useful life of 20 years, to ensure that durable products.

4, the unique housing design, aerodynamic, can effectively reduce wind resistance and reduce the load pole. Plug a hole in the casing design is conducive to the discharge of water on, and combined with waterproof silicone seal to ensure the lighting effects, IP65 degree of protection. Irradiation angle adjustable bracket design, can easily solve the problem without illumination poles, the installation more convenient and flexible to make the design more humane.

Any questions about LED street lights, pls contact us sales@ledcornbulbs.com.http://www.ledcornbulbs.com/

LED Wall light Features

1 Including series of patents, Unique funnel heat sinker, making the lamp better

for heat dissipation. Fresnel teeth lighting design for the PC cover, which is

suitable for wall light distribution.

2 The LED driver and LED light source are separated, which is convenient for

install and assemble.

3 LED driver is movable easily, which helps to replace LED driver.

4 Beauty for the appearance, using Philips or Cree LED.

5 Meanwell Driver are applied.

6 IP65.

Any questions about LED Wall lights, pls contact us sales@ledcornbulbs.com.http://www.ledcornbulbs.com/

What is the different between your LED corn lights with other suppliers?

In today's market, LED corn light looks like all the same, but price very different. We got some emails asking what is the different between your LED corn lights with others?  We do not have any old customer asking about that, most of them already purchase sample to test, and directly see the differences. 

TEKLED have more than 5 years which is the first manufacturer who producing High Power LED corn lights in China. In few years ago, most people focus on home and commercial lighting, such as LED bulb, LED tube and LED spotlights. TEKLED notice so many high power Metal Halide and High Pressure Sodium Lamp used in so many places, and the power consume very high, usually a high bay light fixture is very expensive at meantime. TEKLED started developing and manufacturer LED corn lights since 2008, And after 1 year and half test, they started produce mass products. Initially, they just provide 2 years warranty for the whole lamp. Every design need to continuous improvement. On first generation LED corn light just provide brightness 80lm/Watt (@ CRI>70), today, our LED corn light provide 120-130lm/Watt (@CRI>80)

Usually we do not willing to say compare with other manufacturers, you know, every design have their advantages. 

We have been test same wattage 100W LED corn light with other suppliers.

1. Brightness different. TEK LED corn light lumen output upto 121.7lm/Watt

2. Heating solution design different,  TEK LED useing stamping fin style heat sink with a big size cooling fan for heat dissipation. Well control temperature below 65℃.

3. Driver different-- TEK LED corm light driver all using imported good quality material. 

4. Most LED corn lights copied our designs, but want to provide a cheaper price, so they do not use heat sink or do not have thermal pad.

You can directly purchase our LED corn light to check. You can see the different by you eye even do not use any equipment. 

Want to get more information about LED corn lights? Contact with us today.

Why are so many Chiese consuming foreign brands infant milk powder.

In 2004, fake Chinese-made baby formula that contained minimal nutrition caused at least 12

deaths and malnutrition for hundreds of infants. After that, foreiggn brands infant mil

powder getting more and more popular in China even price much higher. According to the

survey, foreign brands now account for half of all infant milk powder sold in China.

According to the report, the price gap send mainland parents flocking to Hong Kong and

Macao to stock up on foreign-produced milk powder.  A reporter saw a mainland customer

pulling a shopping trolley intended to buy 20 cans of milk powder, but salesclerk asked him

to get only two cans for "there's only a little stock left.". Some supermarkets in Hong

Kong have enatd safeguards such as limiting each customer to no more than three cans of

formula at a time.

What kind of light used in Cattle barn? It looks like high bay lighting fixtures in from the picture. For today, if you want to replacement a cattle barn lighting, you can directly use LED high bay lights to replacement existing high bay lighting fixture, LED light saving more than 60% energy compare with old light fixtures

The different between  SMD2835 and SMD3528 

Core Advantage of 2835 LED:

1, The vertical structure: Chip direct conduction fins to improve the heat dissipation performance, which can withstand the higher current (40-60mA)                    
2, Large heat sink: larger than 3528 heat sink 2-3 times, excellent heat dissipation design, light decay of LED chip life more secure; ,
3.Oversized light-emitting surface: to improve the rate of light: up to 90%.
4, Ultra-thin structure: to solve the 3528 been long-standing problem spot;
5, High optical efficiency: higher than 3528 luminous efficiency 2-3 times the luminous efficiency of up to 130LM / W (@CRI>80);
6, Super stability: low light fades material, process, process maturity and stability.
7, The high cost: to achieve the same luminous flux, than 3528 costs reduced more than 20%

Main different:

1. SMD3528 is old, usually we say  SMD 2835 is update version for SMD3528 and SMD3014

2. Lighting area: SMD2835 is 9.18mm, 3528 is 4.5mm only.

3. Light View Angle: SMD2835 have 120degree light view angle, SMD3528 have 90 degree only.

4. Heat dissipation: SMD2835 have big heat sink for heat dissipation, SMD3528 light source do not have heat sink.So SMD2835 is better

5. Cost: SMD2835 cheaper than SMD3528.Typical 0.2W SMD2835 LED power is approximately equal to 3pcs 0.06W SMD3528.

TEK Lighting Technology which is the first manufacturer use SMD2835 LEDs as light source for maize LED corn lights. The 2835 light sources provide a higher brightness, lower brightness decay.

Do you like to buy branded LED lights?

Not all large lighting brands LED bulb are of high quality. Hong Kong Consumer Council and Electrical and Mechanical Services Department (EMSC) found large disparities in energy efficiency and lifetime performances in 10 types of LED bulbs, among these included products from leading lighting brands. Differences in LED bulb efficacy reached 100%, while one sample burned out and lumen depreciation in certain products occurred at 10% mark of the product’s lifetime. A couple other products failed to pass safety tests. Consumers were advised by the council to choose LED products cautiously.

The council found Panasonic, Ledus, LKKM, Sunshine and IKEA bulbs luminous depreciation declined more than 5% after 3,000 hours of operation, and failed to meet EMSD voluntary energy efficacy label demands, according to a Wenwei Po report. Out of these, Hong Kong LED manufacturer, Sunshine’s, average luminous depreciation reached 30%, about 90% below the advocated 30,000 hour lifespan. The company’s products delivered a miserable performance, six out of 10 samples brightness plunged 70% after 3,000 hours, one even burned out. A far cry from the company’s promoted 30,000 hour lifetime.

The council commissioned an independent la_boratory in Hong Kong to test LED bulbs energy efficiency, and photobiological safety standards. LED bulbs energy efficiency tests require the bulbs to be tested after 6,000 hours (or about 8 months) usage, but due to many new LED bulbs released on the market to prevent products from becoming obsolete before the report was published, the council shortened test time to 3,000 hours (about four months).

EMSD Voluntary Energy Efficiency Labelling Scheme for LED light bulbs. According to the Scheme requirements, the lifespan is defined as the point at which the lumen output of a LED light bulb declined to 70% of its initial lumen when it is considered that the light bulb should be replaced. According to the council, only one brand’s product was spared from lumen depreciation at the 3,000 hour mark, while the others dropped 1.3% to 28.2%.In its efficacy tests, the council found the higher the luminous efficacy, the better the energy efficiency for the same amount of lumen output. Luminous efficacy of the LED bulb models tested varied from 53.8lm/W to nearly double at 107 lm/W. LLKM bulbs delivered the best energy efficacy performance of 107 lm/W, and were also the brightest. In comparison, IKEA bulbs delivered the worst performance of 53.8 lm/W.

TEK LED corn lights make LED lights with more than 6 years experience, committed to provide a high efficiency, high quality, energy saving LED lights. LED corn light lumentoutput upto 120lm/Watt(Ra80), TEK E26 base 12W LED corn light bulb lumen output upto 133.5lm/Watt(Ra80),isolated dirver, CE & RoHS certificated

100W incandescent equivalent LED bulb

Looking for a LED bulb to replacement existing 100W incandescent bulb? The TEK LED corn bulb delivers 1700lm of soft, warm, 4000K light while using just 12watts. The 12W LED corn light bulb design as traditional incandescent lamp base E26 and E27 medium standard screw-type, B22,  Use LED corn light to replacement 100W incandescent lamp, not only saving 88% energy, but also get a higher brightness, and is designed to last 25 times longer than  incandescent bulb.

In addition, LED corn light bulb perfect to replacement CFL PL lights with GX24Q-1, GX24Q-2, GX24Q-3, GX24Q-4, GX24D-1, GX24D-2, GX24D-3 bases available to replacement 32W CFL Plug lights. Energy up to 62%  less than CFL.

TEK LED replacement lamp for 400W HID lamps

TEK's corn LED replace bulb special designed to replacement HID lamps.Simply screw the LED corn lamp into the existing fixture. Low-cost operation, use 70% less energy, provide similar light output 16000lumens.

Low-Cost Operation, 120W LED corn lamp of total system energy 130 Watts, but 400W HID lamp system power consumption upto 460 watts(400W lamp and 60W ballast) , Months to reach return on investment within 3 months.For example:

Simple upgrade, do not need to change existing fixture,medium standard screw-type and Mogul standard screw-type E26/E27/E39/EX39/E40. Do not work on reactor or electronic ballast, just bypass the ballast before installation.

Excellent color redering, Ra>80, lumen output more than 120lm/Watt, CRI70 with a higher efficiency available for your choice. Long Life, 50,000Hrs RATED life, lasts 2.5X longer than HID bulb

Color temperature, available in Warm White:3000-3500K, Nature White:4000-4500K,Day White:5000-5500K,Cool White:6000K-6500K

TEK quality and reliability, 3 years limited warranty

Application: Warehouse lighting,factory lighting, church lighting, gym lighting, workshop lighting, shopping mall lighting 

When you want to replacement your HID lamp about saving money and energy, go to www.ledcornbulbs.com

250W HID equivalent LED bulb--60W LED corn light

TEK's corn 60Watt LED bulb replacement for 250W HID lamps are the easy way to leverage the low energy and long life of LED. Simply screw the LED lamp into the existing fixture, no tools and saving cost.

Features:

Low-cost strategy-LED lamp uses 77% less energy, provide similar light output(7400lm).

For example, 250W HPS using total 290Watts(250Watts HPS lamp and 40Watts Ballast), 60W LED corn light , rated power 64Watts(LED power+driver ) only. Usually you can get back your invest for new LED corn bulb within 8 monthes

Long Lifespan- LED rated life more than 50,000hours, lasts 2.5X longer than HID lamps

Usage safety and Simple Operate-LED corn bulb directly to use in existing open lighting fixtures, such as high bay, low bay, post top lighting fixtures, just remove the ballast

Excellent Color Rendering Index-Ra>80 (CRI70 available, lumen output 10lm/Watt higher than CRI 80)

Color Temperature- LED corn lamp color temperature available in 2700-6500K. (Warm White: 3000-3500K, Nature White: 4000-4500K, Cool white: 6000-6500K) 

Quality and Reliability-3 Years Limited warranty

LED HID Replacement Lamps:

What LED corn bulb do I buy to replace a 18Watt, 26Watt, 32Watt CFL lamp?

Different CFL lamp manufacture have a slight design for light output, LED corn light saving more than 50% energy compare with CFL bulb, that means you can buy a 12Watt corn LED bulb that produces the same amount of light as a branded 32Watt CFL lamp. Plus LED light bulb last up to 2-3times longer and use 2/3 less electricity than incandescent bulbs with similar lumen ratings.

Here are the wattage by Corn LED bulb replace CFL bulbs to producing the same amount of light:

6W LED corn lamp replacement 18W CFL bulb

9W LED corn lamp replacement  26W CFL bulb

12W LED corn lamp replacement 32W CFL bulb

What LED corn bulb do I buy to replace a 60Watt, 75Watt, 100Watt, 150Watt incandescent lamp?

Different incandescent lamp manufacture have a slight design for light output, LED corn light saving more than 90% energy compare with incandescent lamps, that means you can buy a 6Watt corn LED bulb that produces the same amount of light as a branded 60Watt regular incandescent lamp. Plus LED light bulb last up to 65times longer and use 9/10 less electricity than incandescent bulbs with similar lumen ratings.

Here are the wattage by Corn LED bulb replace incandescent bulbs to producing the same amount of light

6 Watts Corn LED lamp replacement 60 Watts incandescent lamp(640lm)

9 Watts Corn LED lamp replacement 75 Watts incandescent lamp(1100lm)

12 Watts Corn LED lamp replacement 100 Watts incandescent lamp(1700lm)

20 Watts Corn LED lamp replacement 150 Watts incandescent lamp(2600lm)

20 Watts Corn LED lamp replacement 200 Watts incandescent lamp(2100lm)

30 Watts corn LED bulb replacement 300 Watts incandescent lamp(3600lm)

50 Watts corn LED bulb replacement 500 Watts incandescent lamp(6500lm)

120W LED corn bulbs replacement 400W Metal Halide high bay bulb in factory

Recycling factory's warehouse upgraded to LED corn lighting which is estimated reduce the warehouse's overall energy use by 71%.

Customer used high bay lighting fixture with mogul base E39 400W metal halide lamp before, the do not want to replacement existing high bay lighting fixtures. And looking for a LED replacement bulb. They have such via internet few times and finally choosing 120W E39 mogul base LED corn light to test first. 

After sample testing, customer very happy with new LED corn bulb, and share with the project picture for reference as below:

Project location: USA

Products in this project: 120W LED corn light

------------------------------------------------------------------

For more information about LED replacement bulb, contact sales@ledcornbulbs.com or +86-150 1411 5394

IP67180W LED FLOOD LIGHT, LED TUNNEL LIGHT--5 YEARS WARRANTY

IP67,180Watt LED Flood Bay Lighting fixture for multiple applications. Perfect for outdoor and indoor applications. Ideal for general lighting of wall washing, tunnel lighting…

LED flood Low Bay Light Features:

lIP67 protection grade, suitable for harsh & tough environment.

lProspectivedesign for heat sink and housing, professional thermal structure, cross-ventilation design improving heat dissipation performance to lone life time.

lClosed corrosion-proof silicone ring for dustproof' scientific fixture design for vibration resistance.

lInstallation friendly, 315째 adjustment tunningangle.

lNo UV and near-IR radiation in the light beam.

lVery low energy consumption, Low thermal output.

lNot suitable for dimmers, electronic switches and remote control.

lCorrosion resistance, suitable for harsh outdoor applications Applied for projection lighting, swimming pool lighting, city decorative lighting, construction lighting, ads lighting, tunnel lighting and workshop lighting.

IP67150W LED Flat Low Bay Light, LED Flood Tunnel Lighting-- 5 year Warranty

IP67,90Watt LED Flood High Bay Lighting fixture for multiple applications. Perfect for outdoor and indoor applications. Ideal for general lighting of wall washing, tunnel lighting…

LED flood high Bay light features:

lIP67 protection grade, suitable for harsh & tough environment.

lProspectivedesign for heat sink and housing, professional thermal structure, cross-ventilation design improving heat dissipation performance to lone life time.

lClosed corrosion-proof silicone ring for dustproof' scientific fixture design for vibration resistance.

lInstallation friendly, 315째 adjustment tunningangle.

lNo UV and near-IR radiation in the light beam.

lVery low energy consumption, Low thermal output.

lNot suitable for dimmers, electronic switches and remote control.

lCorrosion resistance, suitable for harsh outdoor applications Applied for projection lighting, swimming pool lighting, city decorative lighting, construction lighting, ads lighting, tunnel lighting and workshop lighting.

80Watt Corn LED warehouse light

80Watt Corn LED warehouse light is a great option for upgrading conventional high bay light bulb, canopy light bulb and post top street light bulbs.

Unique ultra-light design for weight, internal driver, standard E39 and E26 base. The Corn LED warehouse lighting bulb illuminates with over 9,800lumens at 4000K for at least 50,000hours.

Lamp Base: E26, E27,E39,E40

Over heat protection:

Integral thermal control sensor which reduces driver current, when ambient temperatures exceeds rated temperature.

Dimension:
E40 & E39 size: 4.65'' x 11.62''
E27 & E26 size: 4.65'' x 11.50''

IP67120W LED FLOOD LIGHT, LED TUNNEL LIGHT--5 YEARS WARRANTY

IP67,90Watt LED Flood Lighting fixture for multiple applications. Perfect for outdoor and indoor applications. Ideal for general lighting of wall washing, tunnel lighting…

LED flood light features:

lIP67 protection grade, suitable for harsh & tough environment.

lProspectivedesign for heat sink and housing, professional thermal structure, cross-ventilation design improving heat dissipation performance to lone life time.

lClosed corrosion-proof silicone ring for dustproof' scientific fixture design for vibration resistance.

lInstallation friendly, 315° adjustment tunningangle.

lNo UV and near-IR radiation in the light beam.

lVery low energy consumption, Low thermal output.

lNot suitable for dimmers, electronic switches and remote control.

lCorrosion resistance, suitable for harsh outdoor applications Applied for projection lighting, swimming pool lighting, city decorative lighting, construction lighting, ads lighting, tunnel lighting and workshop lighting.

Difference between incandescent and LED corn light

China's green lighting project aims to promote energy conservation, environmental protection and improve the quality of lighting, to adapt to and serve the social progress and modernization in our country, is one of the measures to strictly limit the low application: ordinary incandescent lighting has become a common requirement for energy conservation and emissions reduction around the world.

Application and efficient lighting products, to promote illumination electricity saving, realize the goal of lighting power saving 10%, In front of the same brightness of dike,led corn light energy saving 60%. Incandescent lamp, fluorescent lamp, halogen tungsten lamp is to use electronic field radiation emitting light, filament light easy to burn, thermal deposition, light attenuation characteristics, and USES the LED corn light is small volume, light weight, epoxy resin encapsulation, can withstand the high strength mechanical shock and vibration, invulnerability to breakage and life expectancy of up to 100000 hours, the service life of the LED corn light and lanterns can reach 5-10 years, can greatly lower the maintenance cost of lamps and lanterns to avoid solitude often changing light.

LED corn light to full solid light source, impact resistance, not easily broken, waste recycling, no pollution to reduce a large number of harmful gases such as sulfur dioxide and nitrogen and carbon dioxide and other greenhouse gases produced to improve the environment and people's life can be called "green lighting light source."

Why we need use LED high bay light replace metal halide lamp?

In the past years, Lighting using scandium sodium metal halide lamp, the lamps and lanterns has high luminous efficiency, good color rendering performance, long service life etc., is a kind of new light source color close to the sun's energy saving, widely used in sports stadiums and exhibition centers, shopping malls, industrial buildings, streets, square, station, wharf and other places indoor lighting.It has high photosynthetic efficiency (65 ~ 140 lm/w), long life (5000 ~ 20000 h), good color rendering (Ra65 ~ 95) compact structure, stable performance, etc.It has both the advantages of fluorescent lamp, high pressure mercury lamp, high pressure sodium lamp, overcomes the defect of the lamp, metal halide lamp brings together the main advantages of gas discharge light source.Especially high photosynthetic efficiency, long life, light color three advantages.

So the development of metal halide lamp soon, use more and more widely. However in the market with other gas discharge lamp, metal halide lamp with mercury in the padding in the lamp, mercury is toxic substances, making light of mercury injection, careless handling, can cause to the production environment pollution and damage to workers' health, arc tube exhaust, there are traces of mercury vapor discharge, if not handled properly, will be directly discharged into the atmosphere, when using the lamp broken, all can cause pollution to the environment.

Now people use led high bay light replace metal hailde lamp , it is famous in the world with environmental protection , energy saving. The light source of led high bay light use solid cold light source , Without thermal radiation, to eyes and skin without any damage.Do not contain lead, mercury and other pollution elements, realize the true sense of the green,People don’t afraid body hurt . In front of the same brightness of dike, than 700 w high pressure sodium lamp 500 w LED high bay light power saving 60%,its life more than 50000 hours.

What is New LED high bay light?

New LED high bay light is different from the traditional industrial high bay light is that adopts high brightness LED as light source, high transmission radiator, optical lenses, or chimney adjust the light Angle of LED lamps and lanterns.Application places and traditional industrial high bay light the same commonly used in large area and high altitude.For example: workshop, warehouse, underground parking, toll station, gas station, supermarket, exhibition hall, gymnasium, etc.


LED high bay light is a lamps and lanterns is used in the assignments section and mine production . LED high bay light is using white light LED as light source, the shell adopts aluminium alloy, cover the lens with high efficiency, heat dissipation article adopts copper and aluminum alloy heat dissipation natural air circulation, make the heat more perfect, the power of LED high bay light only 20% of the sodium lamp, the equivalent of 100 w LED high bay light can replace 500 w sodium lamp .LED is famous in the world with environment protection and energy saving, although price of LED high bay light higher than sodium lamp, after a short time, customer can save menoy from electricity charge.

The emergence of LED high bay light is used to replace traditionalhigh bay light. Why use LED high bay to replace? Because the LED light source has its unique advantages: energy saving, no mercury pollution, long service life, fast response time, security, etc.

Why the LED high bay light is suitable for the industrial zone?

Why the LED high bay light is suitable for the industrial zone? LED high bay light as one of the main national energy conservation and emissions reduction.past several years LED high bay light, ushered the new period ,today green environmental protection is very important , just LED high bay light is a green production and it is famous in the world with environmental protection and energy saving.so LEd high bay light has promoted.LED high bay light also will continue to optimize and improve, in order to better spread to all fields of society. 


LED high bay light is durable, long service life.In our market of lamps and lanterns, the LED high bay light almost all is the use of high quality aluminum alloy materials for the production of lamps and lanterns of the shell, the strength of the aluminum alloy is higher, all aspects of the performance is stable, therefore, after long-term use will not face the phenomenon of deformation, the surface is after a high voltage electrostatic pensu processing, makes the surface of lamps and lanterns is feels comfortable, long service life.
 
LED high bay light lamp and lanterns has certain explosion-proof performance.Considering the particularity of lamps and lanterns use place, we in the production of led mining lamp, have adopted a special explosion-proof structure design, and use to make the lamps and lanterns of toughened glass chimney, and through the die casting process of production, LED high bay light  manufactured goods performance is stable, has a certain explosion-proof performance, use rise very convenient, high safety coefficient.
 
LED high bay light use the low voltage power supply, power supply voltage between 6 to 24 v, and varies according to the product, so it is a safer than using high voltage power supply of the power supply. LED high bay light  lamps and lanterns has excellent heat dissipation function of special types of lamps and lanterns, it is often used by people in the industrial zone, the LED high bay light not only have very good lighting effect, high concentrated sex, but also very environmental protection, its light source very pure, ensure the safety of the people and people don’t afraid of hurting body.
 
 

The brief analysis of the advantages of LED corn bulbs

LED corn bulbs which is a kind of excellent heat dissipation function of special types of lamps and lanterns, it is often used by people to the industrial and mining industry, LED corn bulbs have very good lighting effect, high concentrated sex not only, but also very environmental protection, light, very pure, ensure the safety of the people.

LED corn bulbs is a specially designed for industry effect using kinds of lamps and lanterns, it mainly has the following advantages:

1, LED corn bulbs is very durable and have long service life.High integration of die-casting aluminum lamp shell, the power supply cavity which is completely separated from the light source cavity, the light source inside the cavity is closely combined with LED light source, external heat dissipation wing and air convection, can effectively guarantee the light source and power of life.

2, LED corn bulbs have high light efficiency and very good environmental protection performance.LED is a solid cold light source, is a new type of light source types, using LEDs to produce floodlights, have a very small heating rate, higher light efficiency and low power consumption, is a kind of ideal floodlight lighting appliance.

3, LED corn bulbs failure is small, light failure is less than 3% a year, with 10 years still to use illumination requirements, and high pressure sodium light failure is big, has fallen by more than 30% a year or so, therefore, the LED corn bulbs on the design of the use of power can be lower than the high-pressure sodium lamp.

4, humanized design.Ordinary incandescent bulbs and energy-saving lamps stroboscopic is seen after using for a long time, cause eye fatigue.LED corn bulbs, no stroboscopic, eliminating the traditional visual fatigue caused by light stroboscopic.No lead, mercury and other harmful substances;No ultraviolet (UV) and infrared (IR) radiation.No filament and glass shell, there is no problem, the traditional tube rupture with no harm to human body.

Compared with the traditional lamps and lanterns ,LED corn bulbs has enormous advantages.

 1, save energy and longer life

LED corn bulbs, power consumption is under a third of the traditional lamps and lanterns, life is 10 times that of the traditional lamps and lanterns, you can use for a long time without replacement, reduce the labor cost.More suitable for hard to replace.

2, strong, used for a long time.
LED lamp body itself is used rather than the traditional glass epoxy resin, more solid, even smashed on the floor and the LED will not be easily damaged, it is safe to use.

3, quiet and comfortable, no noise
LED corn bulbs is does not produce noise, for the occasion of using precision electronic instruments as well.Suitable for the library, such as office.

4, the light is downy, protect your eyes
Traditional lamps and lanterns is using an alternating current, so can produce 100-120 times per second the stroboscope.LED corn bulbs is to convert alternating current (ac) directly to dc, won't produce flashing phenomenon, protect your eyes.

5, no ultraviolet, no mosquitoes
Will not produce ultraviolet LED lamps and lanterns, so you don't like the traditional lamps and lanterns, there are a lot of mosquitoes around the light source.Indoor become more clean and tidy.

6, adjustable voltage 80 v to 265 v
The traditional lamps and lanterns is lit by the release of the high voltage rectifier, cannot light up when the voltage reduction.And the LED corn bulbs can light within a range of voltage, also can adjust the brightness.

7, environmental protection, no pollution
A large amount of steam is contained in traditional lamps and lanterns, if broken steam will evaporate into the atmosphere.But don't use the LED corn bulbs and LED products also contains no lead, the environmental protection.LED corn bulbs is recognized as the twenty-first century green lighting.

8, efficient conversion, reduce fever
Traditional lamps and lanterns will produce large amounts of heat energy, and LED corn bulbs is all the electric energy into light energy, not cause waste of energy.And the file, the clothes won't produce fading phenomenon.

LED corn bulbs is suitable for the construction site, the work high above the car, square, park, art Spaces, factory workshop, gyms, golf courses, shops, subway stations, gas stations, buildings, sculpture, green lighting and other places and other parts of the lighting decoration.

Looking for LED hangar lighting?

Today, we got an inquiry from our customer asking for 500Watt LED high bay light

Project: 1750 Square-meters hangar construction lighting

The Expectation:

Customer want to use10-15pcs 500W LED high bay light to achieve 300lux for hangar lighting, reduce Carbon dioxide emission, cut down maintenance cost and save energy bill.

Installation height:7.5 meters

The solution:

In view of 500W LED high bay light cost high, we check our 200W LED high bay light for our customer. According to the lighting simulation, 200W LED high bay light is a better choice for hangar project. Also copper heat pipe heat sink design as 500Watt LED high bay lights, smart lamp thermal management, 5 years warranty.

Total 30pcs LED high bay light 200Watt for this hangar construction, 330lx, no dark area. 

Save money, and only 60.36kWh/day (Base on operation 10hrs per day). Estimated the return on investment is around 14 months after installation of LED high bay light.

LED high bay light used in mechanical workshop

LED high bay light used in mechanical workshop

Today, my customer send me some pictures about 200W LED high bay lights used in his new mechanical workshop.

This project mechanical lighting project located in Qingdao, a coastal city in East China's Shandong Province.

Before that, they had another four workshop using 400Watt HID high bay lights before, and now, this is a new mechanical workshop lighting project, the factory owner Mike want to reduce cost of power consumption. They made a lot of search and tested some samples.

The cost of samples are not cheap, usually TEK Lighting prefer to get all detail information from customer, and then make a lighting solution to customer according to their requirements.

The Expectation:
Project:120x48m mechanical workshop lighting; 300lx
The LED highs install in a height over 11m high ceiling, installation height 9.5meters high, consider to the maintenance inconveniently, there is necessary to choosing a good quality LED high bay light with high lumen output.

The Solution:
 According to lighting simulation, total 90pcs 200W LED high bay light could achive 326lux, uniformity on the working plane u0:0.493
 

Finally, they want to use 200W LED high bay light with hook installation designed, 90 degree beam angle. TEK's 200Watt LED high bay light special use copper heat pipe designed heat sink,
Heat-pipe designed Heat sink

High Brightness Nichia LEDs

The Result:
 The return on investment is around 10 months.Compared with 400W HID high bay light, total annual saving RMB100123.67. 
 

What is warehouse lighting choose LED high bay light should pay attention to?

With the development of the society, the LED industry development in full swing, more and more places are using the LED lamps and lanterns,  especially in the warehouse, LED high bay light used more widely, since LED high bay light post-marketing, has been leading the warehouse lighting market, but the research and development technical personnel has not stopped , continue to develop the next generation of products, constant innovation.
 

Different situations should be considered different emphases .such as coal, petroleum, chemical and other industries to consider dustproof, waterproof, and even explosion-proof requirements when choosing LED high bay light . power, color temperature, flux, etc. It is also an important factor to consider.LED high bay light power to combine actual situation choice, high power will cause the waste of resources, low power and light brightness is not enough, can not meet the lighting requirements.

The general consumers first consider the price when buying LED high bay light, but this is not the only standard of choose LED high bay light.When you choose the high quality product, even if the price is a little higher, also will accept, because buy lamps and lanterns is the mainest is cost-effective.LED high bay light is mainly used in factories, workshops and other fields of industrial lighting, so must choose  good quality, only guarantee the quality is absolutely good, customers will have no trouble back at home.Decided to quality of led high bay light is lamps and lanterns of manufacturer quality supervision whether is qualified or not, whether through the CE certification, only in strict accordance with national quality standard can let consumer choose assured.If you buy  high quality products, not only energy saving , but also saving secondary purchase  lamps and lanterns, maintenance cost of replacement.

When choose LED high bay light to consider above points, if you have not clear place can consultation TEK lighting at any time.

Choose LED corn light used in warehouse lighting can not blindly select

Now LED corn light has played a important role in the lighting, energy conservation, environmental protection,  is the first choice of green lighting.When buying LED corn light must not blindly choice, must according to the actual situation and understand the performance of lamps and lanterns after considering buying the most suitable for their own.Want to buy the most suitable should be from the following points to consider:

1,LED corn light power: power determines the brightness and power consumption.We use lamps and lanterns which is  energy conservation and environmental protection , so we can't choose the lamps and lanterns which is high power, should choose the most appropriate, choose power of the lamps and lanterns  just to meet the need of lighting intensity.Thus we determine warehouse lighting area before buying ,LED corn light brightness and  the number of requirements , Generally the customer is harder to gauge how to choice, we recommend you consult us before purchase;

2,LED corn light quality: quality is the most important to consider a problem, if it is a large lighting places such as warehouse lighting or install lamps and lanterns has the certain difficulty, buy poor quality products, its maintenance is can't imagine, also will be the company suffered immeasurable loss, and to determine the quality is the quality of the production of LED corn light manufacturers whether regulation strictly.

LED corn light is a new generation of green lighting products, energy conservation, environmental protection, long life, but the daily maintenance is must pay attention to, a good daily maintenance can let the lamps and lanterns has longer life, light is more brighter, LED corn light installation must be strong, connection to a standard, read the installation instructions carefully before installation, If you don't install lamp and lantern yourselves ,you should let the professional electricians install, avoid danger happening.

School teaching building lighting  renovation choose and buy LED corn bulbs

How much knowledge of the school teaching building lighting choose LED corn bulbs , most people don't understand.When we are ready for school teaching building lighting renovation also has a lot of knowledge.Now, teach you to choose  good quality  LED corn bulbs.

1, color temperature

It divided into 3000-3500 k (warm white), 4000-4500 k (Nature white), 5000-5500 k (Day white), 6000-6500 k (cold white) .If for living areas such as bedroom, study, can choose the color temperature of warm color department;The work area, such as kitchen, basement, parking lots can choose cool color temperature , see more clearly.

2, lumen

We should  familiar with showed that lamp brightness data.Lumen is higher, the more power consumption?Actually otherwise, the power consumption is related to power, which requires everyone pay attention to the comparison of two parameters when buying bulb, if you have high lumens and low power quickly laid hands on it!

3,color rendering index
Now color rendering index of LED corn bulbs usually up to 70Ra or 80Ra , generally color rendering index ,the higher the better, because show the color of the object will be more real, so when buying LED corn bulbs  remember to ask parameters is also an important thing.

With the advent of the era of the LED, more and more schools in the building lighting reconstruction began to choose LED corn bulbs to replace the traditional fluorescent lamp. 6 W LED corn bulbs can replace more than 30 W fluorescent lamp, save half of the electric charge. Now , what do you think of LED corn bulbs ?

LED corn light is used in underground garage lighting transformation

LED corn light with its high photosynthetic efficiency, energy conservation and environmental protection (do not contain mercury), does not produce harmful such as ultraviolet light, long life and other characteristics, widely used in the underground garage lighting etc.But because of the LED lighting products on the market, the good and bad are intermingled, choose a product which is high efficiency and energy saving， environmental protection and long life is not easy, if you buy a led corn lighting which is photosynthetic efficiency lower than energy-saving lamps and source life shorter than incandescent lamp ,  you will lose more than you gain.

The complete connotation of the green lighting contains comfort, safety, environmental protection, high efficiency and energy saving, indispensable. In addition to having the four advantages, LED corn light has long service life.

1, long service life.energy consumption of LED is low , high efficiency made life of LED corn light is much longer than traditional lamps and lanterns in normal things  , can use without exchange and reduced the artificial maintenance costs.

2, comfortable.LED corn lighting has  the advantages of clear, soft, no glare, no stroboscopic,high color rendering.




3, safety.In the process of the LED corn lights does not produce light pollution , such as ultraviolet light, infrared , good electrical properties conform to safety.




4,environmental protection. reduce the carbon dioxide of power plant emissions so that environmental protection, it is important to LED corn light don't contact harmful substances, such as "mercury".




5, high efficiency and energy saving.LED corn light high luminous efficiency, save energy, it is not hard to understand.


Based on the above points, we know that at the time of purchase LED corn light, to see the product parameters and heat dissipation of components, drive and internal knowledge of the power of the LED products,  help you choose and buy a higher ratio of underground garage illumination application LED corn light products.

The contrast analysis of LED high bay light and Metal halide lamp

In recent years, with the development of LED industry rapidly type, in traditional industrial lighting, metal halide lamp of industrial situation in slowly is broken, the LED high bay light in the lighting industry, have been used more and more widely, why LED high bay light is gradually accepted by people?

1. Environmental contrast
Metal halide lamp fixtures contain mercury, dozens of metal halide lamp fixtures are only contain mercury can pollution throughout the west lake. LED high bay light without pollution element ,such as mercury, xenon, belongs to typical green lighting.
 

2. Brightness contrast
100w LED high bay light brightness is equivalent to 250 w metal halide lamp, the average intensity of illumination is not weakened. 100w LED Luminous is 10000lm.


3. Energy saving contrast
The same Brightness of 100 lamp and lanterns, for example, using 10 hours a day on average, ￥1 per KWH electricity in China, the LED high bay light of electricity is ￥100 a day, metal halide lamp is ￥250 every day.With a 100 w LED high bay light instead of 250 w metal halide lamp fixtures, can save electricity charges of ￥ 4500 per month, can save electricity ￥54750 each year (Equal to $8196.72)

 4.source life
the service life of Metal halide lamp is 8000 hours , LED high bay light can reach 50000 hours . equivalent to turn on the light 10 hours a day, can be used for eight years, greatly reduce the cost of artificial changing light, cost performance is very high.


5. Health contrast
Metal halide lamp would produce ultraviolet and infrared light, cause air drying. LED high bay lighting has no radiation, both to protect the people's eyes and is good for your health.

LED high bay light as a rising star, become the latest must-haves in the factory enterprises due to its high cost performance.Here by the way, I show like to recommend TEK Lighting LED high bay light to you , This is illustrated by the following image.

This is a kind of aluminum die casting process of LED high bay light, the radiator and lamp shell is integrated design, guarantee the cooling requirement and service life of the LED light source, the radiator embedded reflective cup design, irradiation Angle is large, no glare, no stroboscopic, good color rendering, light stability, can meet the needs of different environment. If you choose the LED high bay light, TEK lighting must be your best choice.

Why some LED corn lights will be more brighter in the same power ?

There are often customers will be asked a question, is why the same power of LED corn light, some LED corn light manufacturer produce lamp and lanterns will look brighter, while some manufacturer will appear darker?Today is to reveal the reason for everyone.


First of all, we must clear a concept, the brightness of the LED corn lamp is not determined by the power of lamps and lanterns, but is determined by the luminous flux of lamps and lanterns.Such as  luminous flux of 50 w incandescent is only 1845lm, and a normal manufacturer production of 20 w LED corn light flux over 2200 lm.

LED corn light emitting principle is quite different from traditional lamps and lanterns, LED corn light is composed of nearly hundred lamp bead, each lamp bead power is about 0.3 W, luminous flux according to different chip manufacturers have the difference, and this is reason why the same power of LED corn light brightness is not the same.Purchase of LED lamps and lanterns should use high photosynthetic efficiency lamp bead, the LED corn lamp is more energy efficient.


In addition, some LED corn light  produces the luminous flux ia same , however, because of the color temperature brings the light sensitivity are also different.For example the same luminous flux of LED lamp,adopt high color temperature will appear more bright.


Cause same power of LED corn lamp has different brightness for many different reasons, for the average user, if you don't know how to choose LED corn light, You can choose some powerful factory.For example ,TEK lighting is a professional engaged in production of LED lamps and lanterns manufacturers, if you have a problem can consult them online customer service.

The contrast analysis of LED high bay light and Metal halide lamp

In recent years, with the development of LED industry rapidly type, in traditional industrial lighting, metal halide lamp of industrial situation in slowly is broken, the LED high bay light in the lighting industry, have been used more and more widely, why LED high bay light is gradually accepted by people?

1. Environmental contrast
Metal halide lamp fixtures contain mercury, dozens of metal halide lamp fixtures are only contain mercury can pollution throughout the west lake. LED high bay light without pollution element ,such as mercury, xenon, belongs to typical green lighting.
 

2. Brightness contrast
100w LED high bay light brightness is equivalent to 250 w metal halide lamp, the average intensity of illumination is not weakened. 100w LED Luminous is 10000lm.


3. Energy saving contrast
The same Brightness of 100 lamp and lanterns, for example, using 10 hours a day on average, ￥1 per KWH electricity in China, the LED high bay light of electricity is ￥100 a day, metal halide lamp is ￥250 every day.With a 100 w LED high bay light instead of 250 w metal halide lamp fixtures, can save electricity charges of ￥ 4500 per month, can save electricity ￥54750 each year (Equal to $8196.72)

 4.source life
the service life of Metal halide lamp is 8000 hours , LED high bay light can reach 50000 hours . equivalent to turn on the light 10 hours a day, can be used for eight years, greatly reduce the cost of artificial changing light, cost performance is very high.


5. Health contrast
Metal halide lamp would produce ultraviolet and infrared light, cause air drying. LED high bay lighting has no radiation, both to protect the people's eyes and is good for your health.

LED high bay light as a rising star, become the latest must-haves in the factory enterprises due to its high cost performance.Here by the way, I show like to recommend TEK Lighting LED high bay light to you , This is illustrated by the following image.

This is a kind of aluminum die casting process of LED high bay light, the radiator and lamp shell is integrated design, guarantee the cooling requirement and service life of the LED light source, the radiator embedded reflective cup design, irradiation Angle is large, no glare, no stroboscopic, good color rendering, light stability, can meet the needs of different environment. If you choose the LED high bay light, TEK lighting must be your best choice.

Identify the advantages and disadvantages of LED high bay light

With development and constant improvement of LED technology, LED in lighting field permeability has been maintained a high growth momentum.And lighting time is long, large energy consumption of industrial lighting, gradually become the latest must-haves in the LED lighting manufacturers, all LED lighting manufacturers are basically in industrial lighting field, and as the main industrial lighting products，LED high bay light became every manufacturer must to do.But the problem is that in the  allocation of resources is unequal,  technical strength is unbalanced.  It is easy to appear the quality problem .

Analyze LED high bay light from the structure , can be divided into three main components: LED light source, LED driver, LED heat dissipation.How to distinguish the quality of the LED high bay light,  layman can from the following several aspects to distinguish good or bad :

1, compare the luminous efficiency of LED high bay light, measuring the flux , luminous efficiency  (single flux value) more than 90 lm/W belong to high luminous efficiency product , luminous efficiency is lower than 80 lm/W belong to low light efficiency product .

2, compare the PF value of LED high bay light,  PF value is between 0.90 ~ 0.96 best, PF value higher than 0.96 is too high, PF value below 0.9 belong to the poor quality.

3, compare the conversion efficiency of  LED high bay light, measuring the actual power and light source power of the lamps and lanterns , conversion efficiency is more than 80% belong to the qualified products, less than 80% belong to the inferior products.

4, IP protection index, if use big environmental dust, humidity,  requires the disposal of the IP protection, otherwise the service life of the LED high bay light will be significantly reduced.

Do you know how to buy LED high bay light?

The LED high bay lights has multiple advantages, and therefore is widely used in workshop, factories, mines, shipyards, gas stations, large supermarket, gym and so on. LED high bay light includes the following several aspects:


First, LED high bay lighting production technology is advanced, the fan in wind cooling principle, can fully take internal heat flow discharge in time, thus reducing its temperature, ensure the cooling requirement and service life of the LED light source, The surface of  lamps and lanterns is anode oxidation prevent corrosion, compact structure and beautiful.LED high bay light use the acicular radiator cooling efficiency than conventional flake radiator is greatly improved, can make the LED junction temperature lower than the ordinary radiators 15 ℃.


Second, the LED high bay lights has the characteristic of long life, its unique chip technology to fully guarantee the service life of the light source.Combined with LED high bay light, the radiator and lamp shell integration design, can guarantee the service life of the lamps and lanterns.


Three, the LED high bay light unique group chip integrated single-mode light design, selection of imported high brightness chip, the encapsulation of high power LED as light source, its high thermal conductivity, light failure is small, light color purity, no ghosting phenomenon.Good color, can meet the needs of different environments, enhances the working efficiency.


Four, energy saving, using single chip integrated high power LED light source is equipped with more efficient power, more than 75% than the traditional energy-saving lamps and lanterns of the same brightness.


Five, green pollution-free.LED high bay light ,no aluminum, mercury and other pollution elements, so don’t cause any pollution to the environment.

Why LED panel light is the first choice for the subway?

Why LED panel light is the first choice for the subway?Aiming at this problem, we first to know about the subway lighting design requirements.


The design of underground lighting requirements:


1, underground power distribution system is complex, the voltage fluctuation is frequent, the working voltage range of lamps and lanterns, need to lamps and lanterns is more stable.LED panel light can be  85-265  v or 100-240 v input voltage range.


2, the subway lighting is used in a closed space, lamps and lanterns is working time is longer, are generally not more than 17 hours, traditional lamps and lanterns droop in this environment is very large.Naked and LED light source in the node temperature lower normal work, can achieve 5000 h light failure, the whole lamp heat handle basic can achieve 5000 h light failure is less than 1%.


3, short service life of traditional lamps and lanterns, need maintenance repeatedly, can bring huge workload to the subway operation and the certain difficulty.LED panel lights, there are more than 50000 hours of stable life, and can design as a way for easy maintenance, has greatly reduce the amount of daily maintenance.


4, the electromagnetic interference influence on communication equipment will be in the subway, especially near the location of the train operation, to avoid the electromagnetic interference is very important.Good design can will generate electromagnetic interference control LED panel light is very low.


5, as the subway tunnel traffic, running area full of wave type vibration energy, the anti-shock performance of lamps and lanterns is very important.LED panel light has a unique way of luminescence, lamps and lanterns can design a special seismic structure.


6, LED panel light has a very wide range of design options, enough to create a unique atmosphere of the subway station.


Thus, LED panel light is the first selection of the lighting.

Why LED high bay light choose constant current driver?

Some time ago,a customer bought 150W LED high bay light , We gave him configuration meanwell power supply which is constant current driver.Customer asked why 150w LED high bay light use constant current driver?

Constant current drive is to protect the normal use of  LED high bay lights,most of the time with the use of voltage instability, the high temperature.Constant current is within a certain range of output voltage,output current is kept constant,is an important factor of stability in LED high bay light service life.

150w led high bay light belongs to the typical nonlinear original, using constant current drive even under the premise of non steady flow can normal use don't burn out.Under the normal use of led high bay lights on both ends of the voltage is 220 v is input,there is three lines ,live wire ,zero line and  ground lead,read the instructions carefully before you use, firewire and zero line must not be wrong.Constant current drive on the price a little higher, but the late safety to use more at ease, for the sake of your health ,we recommended that you purchase led lighting products which has constant current drive .

Market for 150 w LED high bay light choice depends on the performance of the product , drive is the important factors of affect lifespan  .Drive is a power supply module, the objective is to protect the normal use of the led high bay lighting.

Why general purchase suggestions constant current drive, actually it is a prevention effect, because we often use voltage 220 v, if it is the current converter connected to the must be less than 220 v, in use will be affected, lead to voltage instability or components burn out.


use constant current regulator, would be a little higher,but  quality guaranteed is very important.

How to choose high quality of LED high bay light?

How to choose high quality of LED high bay light? This is what people care about, Now , let's take a look.

1, the luminous efficiency
LED lighting technology becoming mature, high power LED light source has can meet the general high bay light luminous flux as needed.The average high pressure sodium lamp light efficiency is 100 lm/W, but the color temperature is poor.The higher luminous efficiency, energy saving effect means the better, which is one of the most important indicator to choose LED high bay light  .TEK LED high bay light  are more than 130 lm/W, however, LED does not have explicitly stipulated in the standard, so must be carefully confirmed when purchasing LED high bay light.


2, light failure
light failure of LED high bay light is mainly related to choose what kind of chip as well as how to strengthen the heat dissipation.Some businessmen in order to reduce costs, with hundreds of small power LED 0.5 W.However, this kind of small power LED light failure is very serious, its light failure and 80% of life is only 1000 hours.Therefore, as the need for long-term use, lamps and lanterns is absolutely not allowed use of this kind of small power LED, selects the high power LED, the light failure will be much better.


3, heat dissipation
LED is semiconductor components, its wafer is affected by temperature and reduced to 30% of the initial luminous flux, will lose meaning of lighting, also is the life end.Theoretically the life of the high-power LED high bay light is 50000 hours, but the premise is to have a good heat resistance.such as TEK lighting product 180W LED high bay light, Adopt the acicular radiator cooling efficiency than conventional flake radiator is greatly improved, can make the LED junction temperature 15 ℃ lower than the ordinary radiator above, its good heat dissipation performance, ensure the service life of lamps and lanterns for a long time and stable reliability.

 Do you know how to choose high quality of LED high bay light ? if you want to more information,please contact us .
 

Heat guaranteed of LED high bay light

LED high bay light is a lighting lamps and lanterns with LED chips as light source,  as people deep understanding of it, has been widely used in factories, mines, warehouse, production areas of high tent.Because of the complicated environment of these places, its cooling is extremely important.And as the light source of LED chips, if not timely reduce temperature, will lead to many problems.

 
In fact, the heat dissipation is not timely, in addition to affect the efficiency of itself of lamps and lanterns, under a certain degree can also affect the entire site environment.And now in the market of LED high bay light, mostly adopts centralized heat, lamps and lanterns  Performance is poor , poor reliability .We can not help but worry about such a situation, how to guarantee the reliability of the lamps and lanterns, security lighting work?

 
Produced by domestic leading brand TEK LED lighting LED high bay light adopts the module structure of fins, lamps and lanterns back hollow out, the formation of convection, reduce the chip temperature, improve the reliability, reduce the fault of lamps and lanterns, lamps and lanterns have more than 50000 hours service life , LED high bay lightcan be more than 80% and save electricity so that 180w LED high bay light can replace 450w metal halide light.

Why the LED high bay light is more energy efficient than traditional lamp?

Now our factory, workshop usually adopts the industrial lamp for lighting, but not environmental protection.With the advancement of LED industry, LED lighting lamps and lanterns has the characteristics of energy saving and environmental protection, therefore, the LED high bay light to replace the traditional high sodium lamp is the inevitable trend of era development.

Why the LED high bay light  is more energy efficient than traditional?Because the LED high bay light is using high brightness white light LEDs is a new generation of solid cold light source, calorific value is not high, the electric energy into light energy as much as possible;And many ordinary lamp for calorific value is big, the electrical energy turns into heat energy, caused wasted.In contrast, LED high bay lighting is energy saving.
 

With the continuous and packaging technology improvement of the LED chip, price is more and more lower.In addition, the LED high bay light not only have the functions of energy saving, environmental protection, but also it can adjustable light, good light efficiency, long life, LED lighting popularity brings not only energy saving.

What is the advantage of high power LED high bay light?

High power LED high bay light is high pressure sodium lamp alternative products, What is the advantage of high power LED high bay light?

First, single phototaxis
LED high bay light itself characteristics - the unidirectional light, no light diffusing, guarantee the efficiency of light.
    
Second, the light is strong
LED high bay light has a unique optical design, LED high bay light shine to the desired lighting area, further improve the efficiency of the light.Has reached the energy saving purpose.At present, the LED high bay light source efficiency has reached 130 lm/w, also has the very big development space, and the theoretical value of 200 lm/w.And high pressure sodium lamp luminous efficiency was increased with the increase of power, as a result, the overall LED high bay lights better than high pressure sodium lamp.
   
three, light color
LED high bay light light color rendering many higher than the high-pressure sodium lamp and high pressure sodium lamp only around 23, and LED high bay light can more than 80, from the psychological point of view, vision to achieve the same brightness.
   
Four, light failure is small
light failure of LED high bay light is small, light failure is less than 3% a year, with 5 years still meet use lighting requirements, and high pressure sodium light failure is big, has fallen by more than 30% a year or so, so the LED high bay light on the design of the use of power can be lower than the high-pressure sodium lamp.
    
Five, easy to maintain
Each unit LED only a small size dice, so you can preparation was the various shapes of components, and is suitable for variable environment.


Comprehensive the above principle, theory of LED high bay light has energy saving, long life, environmental protection lamp advantages, advocate green environmental protection all over the world is very bright, with government and industry attaches high value and vigorously support.

TEK Lighting new product --DLC UFO LED high bay light

As is known to all, the current market in the United States and Canada lighting, DLC has gradually become the LED lamps and lanterns indispensable certification standards.TEK lighting new products UFO LED high bay light has passed the certification of the DLC, the quality of the products  is guaranteed, all our products have three-year warranty and lifetime maintenance, so customers can buy it assured.

The shape of UFO LED high bay light based on the traditional high bay light make improve.The structure of the flat heat dissipation area is larger, high thermal conductivity,  therefore,  UFO LED high bay light service life is longer,  light failure is lower.its lighting effect are also more than 30% higher  traditional industrial lighting effect, UFO LED high bay light products according to euramerican style design, refined aesthetic shape, so gradually popular in European miner's lamp application market. 

At present UFO LED high bay light is mainly used in warehousing, logistics, and large industrial plants, and other areas of the traditional industrial lighting replacement.Its beam Angle from 60 ° to 120 °, can be applied to all kinds of lighting environment.

What's the advantage of UFO LED high bay light

We all know that a UFO high-power LED high bay light is lighting lamps and lanterns, it passes through unique thermal design .it also has  good performances ,such as safety, environmental protection, energy saving,  slowly let consumers to accept and use;Now all over the world advocate energy-saving, environmental protection, so the new technology of UFO LED high bay light will be widely used  is very necessary.

Today, many large factories, warehouses, docks, gymnasium, exhibition hall all need high power lighting, TEK Lighting  UFO LED high bay light products by combining different customer requirements, design diversified lamps and lanterns, conform to the state of "low carbon, green life", and more consider consumer costs,now  UFO 100 w LED high bay light brightness can reach 150 lm/w, its service life  more than 50000 hours, energy-saving dozens of times than traditional lamp .  because of its good use performance,UFO LED high bay light won't produce maintenance after installation, it is also can save maintenance cost.

What's the advantage of UFO LED high bay light?

1,All aluminum housing for the heat dissipating, greatly extends the life span of lighting source.

2,Free of dust and water, suitable for outdoor.

3,High quality led power supply, long life time.

4,Ultrathin design , convenient for storage, transportation and maintenance.

5,Waterproof : IP65

6,High pressure casting ,proceed by painting ,solid an corrosion resisting.

What is the UFO LED high bay light?What is the distinguishing feature of UFO LED high bay light?

As the incandescent light bulb gradually disappear, UFO LED high bay light as the main force of the energy conservation and environmental protection gradually rose to the surface and is well known.So, what is UFO LED high bay light? What is the distinguishing feature of UFO LED high bay light?


What is the UFO LED high bay light?
UFO LED high bay light, due to the unique design, look like a UFO. It is made of a high precision automatic equipment forming of heat dissipation fin aluminum housing, good heat dissipation effect, UFO LED high bay light using many lamp bead which is high power, high luminous efficacy and high color rendering index. Uniform light , long life , light failure is small , can be widely used in outdoor and indoor all sorts of bad application environment .

What is the distinguishing feature of UFO LED high bay light?
1, UFO LED high bay light using many high power LED as light source, with high thermal conductivity, light failure is small, light color purity, high color rendering index, no ghosting, etc;

2, the unique design of heat dissipation fin, light source perfect combine with radiator ,effectively conduct heat diffusion, thereby reducing the lamp body temperature, effectively ensure the service life of the light source and power supply.

3, green , environmental protection ,no pollution. UFO LED high bay light do not contain lead, mercury and other pollution elements, UFO LED high bay light without any pollution to the environment.

4, good color rendering, more real to physical color rendering.A variety of color optional, which can meet the needs of different environment, UFO LED high bay light eliminates the traditional lamp color temperature cause of depressive mood, make visual feel more comfortable, improve the work efficiency of the workers.

5, UFO LED high bay light using constant current and constant voltage control, apply voltage wide (AC90 -305 v) overcame caused by power grids, noise pollution cause light is not stable, to avoid the work brings to the eye irritation, fatigue;

6, adornment effect is good, the use of special surface treatment technology, can choose a variety of color appearance, simple installation, convenient disassembly, wide application scope.

What are the main distribution channel of UFO LED high bay light ?

Buy a  UFO LED high bay light has three ways , stores directly take goods, manufacturers wholesale supply and online orders to buy .But which one of the three channels for late, lamp quality guaranteed?

1, store directly take goods: directly in the store to buy a UFO LED high bay light. if lamps and lanterns has quality problem can return ,and Changing or Refunding in the storekeeper promised time.

2, manufacturers wholesale supply: this class is generally requires a lot of UFO LED high bay light customer group, have lamps and lanterns brand agents and long-term wholesale, usually will have quality problems of products accumulate up, later sent to factory for replacement or exchange a purchase.


3, online order for: according to majority customers buying habits with retail, platform to buy is guaranteed, to the quality problem of the UFO LED high bay light according to the agreed warranty time,  looking for sellers customer service communicate , general is no problem, once the merchants  don't want to deal with after-sales problems, can complain directly to the third party intervention, for sellers don't want to get out of trouble.
 

TEK lighting as UFO LED high bay light manufacturers, there are three distribution channels: online trading, offline trading, or Customers to the factory take goods .  the first two ways are already turn into express or logistics way to deliver goods, just the payment terms is different.The third is to provide local customers, to meet the different customer buying needs.TEK UFO LED high bay  lighting products quality assurance is 5 years, don't worry about the quality of the lamps and lanterns .

About UFO LED high bay light, what do you want to know?

Produced by TEK lighting ,UFO LED high bay light can do 60 w to 240 w, power is optional, according to different wattage, installation height can reach 8 to 15 meters, uniform illumination, no dark space.High purity aluminum reflector, lamp shell and the cooling body;5 mm high strength tempered glass; single high power LED light source;High efficiency imported constant current source. UFO LED high bay light can be used as power range: 60 w, 80 w, 100 w, 120 w, 150 w, 180 w, 200 w, 240 w.UFO LED high bay light advantages: high light efficiency, prevent glare,  waterproof grade IP65, beautiful, good heat dissipation effect, packing small volume, greatly reduce transport costs, and improve the product performance.

What place can UFO LED high bay light used in ?  
 UFO LED high bay light application is very extensive，it can be divided into indoor and outdoor illumination, its IP protection grade reaches 65, waterproof, explosion-proof, fire prevention.applied to the lighting in common places ，such as: high canopy ceiling lighting , warehouse,  waiting room, stadium, movement hall ... 

The service life of UFO LED high bay light and how to maintain?  

Unique heat dissipation  of lamps and lanterns and light shell integration design ,
Effective heat conduction diffusion, thereby reducing the lamp body temperature, ensure the LED light source service life of 50000 hours.Calculated according to light up 11 or 12 hours a day, UFO LED high bay light in 10 years without replacement.Work in the atmospheric environment of lamps and lanterns, be sure to have dust attached on the surface of the lamp body, over time the dust on the lamp body Be sure to affect the heat dissipation which affects the service life of the lamps and lanterns of lamps and lanterns.What are we supposed to do?Actually very simple, every once in a while for the heat lamps and lanterns on clean with dry cloth, can guarantee the service life of UFO LED high bay light.

The present situation and prospect analysis of UFO LED high bay light

UFO LED high bay lighting using LED as light source, compared with general lighting lamps and lanterns, has more advantages.As we all know , LED high bay light is famouse for  energy conservation and environmental protection, its high efficiency and long life is fit for people.

The first two years, UFO LED high bay light in the commercial and industrial category to get fast development, follow the skills,  at present UFO LED high bay light is beginning to enter the home lighting category, and achieved good results.

Currently, hinder UFO LED high bay light  to enter civil market factor mainly has two aspects: on the one hand, because the social awareness on LED skills and goods is still in its infancy,  consumer  can be cognitive  LED light share only 25% in China, UFO LED high bay light want to all over, raising consumer awareness is still the key. On the other hand, because the commodity prices of  UFO LED high bay light is higher than traditional lighting  higher, most home users only see short-term interests, rather than put energy-saving benefit for a long period of time in thinking, therefore, the UFO LED high bay light penetration rate always difficult to perfect.

To improve the penetration rate of UFO LED high bay light must start from two aspects of this,  in the propaganda LED knowledge at the same time, use the way that with skills to promote productivity to gradual decline the price of the UFO LED high bay light, promote global use.

Trust hurtling along with LED lighting skills, as well as the consumers about LED knowledge are added, the future of UFO LED high bay light throughout will be soon.

Workshop use UFO LED high bay light to replace incandescent lamp can save more than 60% of the electricity

UFO LED high bay light has a wide application area and a promising prospect, such as warehouses, factories, workshops and other lighting places.How about The factory use UFO LED high bay light  instead of incandescent lamp?

TEK Lighting UFO LED high bay light adopt famous brand led light source and aviation aluminum radiator, has a high quality assurance. UFO LED high bay light has the advantage of energy conservation and environmental protection, 250 w LED high bay light is equal to 600 w metal halide effect.

Factory has production equipment, workers, sealing is better, of course there are security hidden danger is higher, the UFO LED high bay light has excellent explosion-proof performance, relatively safe hidden trouble is smaller.One of the main purpose of the workshop use UFO LED high bay light is because of energy saving.Long time operation, power Consumption is bigger, use UFO LED high bay light can save more than 60% of the electricity, a year can save much electricity, greatly reduce the cost of operation.

UFO LED high bay light not only save electricity, but also a service life of it more than 50000 hours, up to 10 times longer than traditional light, is almost maintenance free, save the cost of replacing the lamps and lanterns and trouble.Although the price relative to the ordinary lamps and lanterns is a bit more expensive, but the energy charge can be saved in return for the cost.Workshop use UFO LED high bay light with good lighting effect , its brightness is high, the light failure is small, good color rendering, can illuminate every corner of the workshop, make visual feel more comfortable, improve the work efficiency of the workers.

In addition, UFO LED high bay lighting also conforms to the concept of green and environmental protection, do not contain lead, mercury and other pollution elements, also do not contain large amounts of radiation, will not cause the harm of users  ,it is a typical green lighting source.Above all, TEK lighting UFO LED high bay light is a good choice!

What is the best choice of workshop lighting?

We can see UFO LED high bay light in many areas , as the design of UFO LED high bay light has a relatively good appearance and good heat dissipation effect, so that we all tend to be particularly fond of, and UFO LED high bay light can bring us a lot of convenience In the aspect of energy conservation.

Factory has higher requirements for brightness, general people use high-power incandescent lamp, tungsten filament lamp and UFO LED high bay light.Compared with other lamps, UFO LED high bay light not only save energy to reduce resource consumption, and safety performance is more outstanding.In coal mine underground has high degree of safety requirements, UFO LED high bay light is more popular.Choose UFO LED high bay light, unlike traditional high-power lamps and lanterns,Metal halide light need 400 w , UFO LED high bay light only need 100W. UFO LED high bay light have been more can guarantee the security of its quality, according to the use of a particular place to choose the appropriate color temperature. 


UFO LED high bay light has the good explosion-proof performance and long life characteristics, we can use in some inflammable and explosive places.As a result ,our lamps and lanterns is in the process of use will generate heat, so its design must be very good attention to this point. usually used by cold light source, the light source to ensure that won't produce too much heat value, in this way can make us more convenient in use. 


And compare to ordinary lamps and lanterns,UFO LED high bay light unique place embodied in need voltage is lower, so that to use more secure.Due to the relatively low voltage, the frequency of power accident is relatively low, and because itself penetration is stronger, so fewer scattered light, and therefore its use life will be more longer.As a kind of green light source, the absolute is a good choice for all of us.  

What are the factors influence workshop lighting effect?

Workshop lighting is affected by many factors, the main influencing factors are the following two:

1, lighting environment, illuminance and brightness must even, the ceiling height and the height of the installation of lamps and lanterns has certain requirements.

2 characteristics of LED high bay light,it must have very good heat resistance, color rendering and energy saving, high luminous efficiency.

Most of workshop for LED high bay light request is not high, and  more consider  light utilization efficiency and economy, so commonly used high-power LED high bay light.

Lighting engineering concept is very wide, according to the different types has landscape lighting, building lighting and road lighting, the general in the engineering application is  good quality special lamps and lanterns.Application requirements are as follows:

1, engineering lighting usually use outdoor lamp, according different place to  choose waterproof grade IP. such as TEK Lighting 1000W LED high bay light is IP65,  it can adapt to bad environment.

2, quality is the key.In addition to the material requirements as well as internal heat dissipation, it is best to take priority of radiator. TEK Lighting 1000W LED high bay light has a high quality of the radiator, is able to timely heat dissipation and protection of the life span of the lights.

3,high-power products pay attention to light bead quality, must be constant current drive, because once the installation is hard to change . TEK Lighting 1000W LED high bay light choose Cree firstly, bring a better experience to the customer.

The light pollution refers to the inappropriate way of harm the eyes by lighting.Is generally is the power of lamps and lanterns is too big, cause dazzling vertigo;As well as the inappropriate use of lamps and lanterns, put the wrong location affects the normal use.

Don't limited to the understanding of the LED high bay light, not the brighter, the better, suitable is the best, to send to friends who don't know how to make good use of the LED high bay light.TEK Lighting warm reminder: best to buy quality assurance when buying .

Design LED high bay light need to pay attention to several points

The design of the LED high bay light, involved in more detail, we according to the following several important considerations, to reflect the design process and methods:


1,power 
Traditional mining lamp with 250 w and 400 w high pressure sodium lamp and metal halide lamp, and compared the characteristics of the new type of LED high bay light has evident difference:200w LED high bay light replace 400W metal halide lamp.

2 light source choice
At present the well-known brands high power LED light source on market are: CREE, OSRAM, NICHIA, Lumileds (the earliest LED) ,  TEK Lighting LED high bay light choose Cree firstly.

3 the cooling design.
Used in  LED high bay light, heat dissipation is a big problem. if not add cooling measures, LED high bay light temperature will rise sharply, when its junction temperature (TJ) rise more than the maximum permissible temperature (typically 150 ℃), LED high bay light will be damaged due to overheating.So the cooling design also is our most important content.

LED high bay light usually used in large-scale factory building, product quality is very important. So when you buy LED high bay light,  you must pay attention to product quality.

Why LED high bay light is popular with people ?

LED high bay light used in factory, the use of high photosynthetic efficiency of LED lamps, LED light source with high efficiency lens is suitable for working in the factory and warehouse, etc.Excellent domestic industrial and mining lamp manufacturers products are particularly exports.

Factory has higher requirements for the LED high bay light, especially international enterprise standardization workshop, for cleanliness, working environment, such as temperature, light, stroboscopic has a certain quantitative standard, in order to achieve energy saving, high efficient and safe environment.

TEK lighting LED high bay light, no mercury and other harmful substances, energy conservation, environmental protection, in accordance with international law of environmental friendly, is conducive to establish international enterprise good corporate image.

At the same time, the lamp body uses the aluminum alloy material, compact structure, smooth surface design, not easy to dust, accord with the requirement of building high cleanliness.Lighting the light is downy, no glare, no dark space, no stroboscopic, is especially suitable for mechanical operation, due to the insufficient light, serious stroboscopic prevent safety accidents.

Click here to edit header

LED lamps and lanterns is according to the actual applications can be divided into indoor lighting and outdoor lighting lamps and lanterns.LED  light in the two region has the corresponding lighting products.

Outdoor lighting lamps and lanterns, we have LED high bay light, LED high bay light with high efficiency and energy saving, long life, environmental , will become the best choice of the industrial lighting .Due to the particularity of industrial lighting, LED high bay light ,waterproof, dustproof, apply to high and low temperature environment.Our LED high bay light have toughened glass protective , all metal thermal conductive path cooling, can fully meet the above requirements.

Indoor lighting mainly is LED panel light.LED panel light application scope is wide, such as schools, hospitals, supermarkets and other places can be used.Light source using LED as light source, high efficiency and energy saving, convenient installation.Our LED panel lights imported chips, high brightness.Heat dissipation fully and low light failure. LED panel light is no bad glare, won't produce flashing phenomenon, the light is downy, it is helpful for people to protect your eyes, also won't produce purple outside, no radiation, no mosquitoes around around, make the environment more health ,clean and tidy.

New type of green light source of LED lamps and lanterns, continuously improve the lighting effect, more and more humanized lighting products on the market of lamps and lanterns appear constantly.TEK lighting will continue to comply with market trend, design better LED lamps and lanterns, let everyone enjoy the green lighting .

Limit LED high bay light development factors

Click here to edit text.

How to design the LED high bay light?

In fact, the traditional light source in a certain extent has satisfied people demand for lighting, but why the LED high bay light will still get the welcome of consumers?In fact completely because of the difference of lighting effect.This kind of product design, because  market need this kind of lighting effect demand.

For example, in some special circumstances, in order to build a certain atmosphere, often need to have lighting effects.But the traditional lighting effect is not reach such effect.So the LED high bay light is designed accordingly.Through such products were produced  lighting effect tends to more special.So in the process of design is the need to satisfy two conditions.

The first condition is that the demand of the market, there was no professional lighting products to achieve such effect, so the LED high bay light has been designed.The second condition is that a lot of special occasions need different atmosphere, the traditional light source is to reach the effect.LED high bay light has different color temperature and color rendering index, can meet people requirement.

Under the condition of the two, this kind of LED high bay lighthas been designed, and we see the products on many occasions can play a special effect now, consumers are very satisfied.So here the design of LED high bay light is absolutely more correctly, can completely meet the lighting demand of all consumers.

The three characteristics of LED high bay light

The main light source for lighting are fluorescent lamp, incandescent lamp, metal halide lamp, high-pressure sodium lamp, halogen tungsten lamp and LED high bay light etc. in addition to LED high bay light ,others light source for decades or even hundreds of years of development history, technology is relatively mature, and is the market mainstream now. But the LED high bay light with energy-saving get attention all over the world. With the rapid increase of technology, the LED high bay light price also fall, at the same time, rapid advance the application of LED  high bay  light all over the world.

The characteristics of the LED  high bay lamp

Energy saving. high efficiency and energy saving ,no pollution, low power consumption, over 70% of energy saving than traditional light source;

Environmental protection. no ultraviolet and infrared in the spectrum, no heat and radiation, can safely touch, belongs to typical green lighting source;

Long life. at present, the LED has reached more than 100000 hours, with the continuous development of LED technology and popularity ,drive and heat dissipation is fundamental to achieve the ideal state, commercially available high quality LED high bay lighting life reached 10000-50000 hours, almost is 10 to 50 times the ordinary halogen lamp.

The use contrast of Metal halide lamp fixtures and LED high bay light

LED as a new light source compared with the traditional light source, when make directional illumination lamps and lanterns—LED high bay light, than the traditional light source made of the same type lamps and lanterns saving energy by 40% to 60% .in the heat dissipation ,structure design of LED high bay light is reasonable. If choose good driving power supply , the life of LED high bay lights up 50000 hours.

The metal halide lamp fixtures and LED high bay lighting use contrast analysis report:

A, alternative

1: general substitution principle

LED high bay light only 50-60% of metal halide lamp power can achieve the same Luminous Flux.

For example of 200 w LED high bay lights can replace 400 w metal halide lamp

2， choose the light Angle of lamps and lanterns

As in the local work, turn on the light in the work area to meet the requirements of illumination, the smaller the Angle, the less the number of lights, save electricity.LED high bay light Angle 60 °, 120°。

3，Color Rendering Index

Used LED high bay light replace Metal halide lamp, can bring a comfortable eye environment. So the applied range of LED high bay light  is large than MHL and more popular among people.

What about workshop use 150W LED high bay light?

TEK Lighting LED lamp fixtures scope more extensive, such as warehouses, factories, workshops and other places . it  is a great energy-saving lamps and lanterns, what about workshop use 150W LED high bay light?

TEK 150 w led lamp fixtures has excellent explosion-proof performance, relatively safe hidden trouble is small. one of the main purpose of the workshop  use LED high bay lighting is energy saving ,150 w LED high bay light can replace 250 w high pressure sodium lamp, it in terms of energy saving is very excellent. Workshop is a long time operation, the power consumption is large, workshop with 150 w LED high bay light can save two-thirds of electricity, a year can save a lot of electricity charge, reduce the cost of operation in the workshop.

 Workshop with 150w LED high bay light not only save electricity, but also service life is more than 50000 hours, 10 times longer than traditional light, is almost maintenance free, save the cost of replacing the lamps and lanterns and trouble.

Although the price relative to the ordinary lamps and lanterns is a bit more expensive, but the electricity can be saved in return for the cost.Workshop has good lighting effect with LED high bay light, brightness is high, the light failure is small, good color rendering, can illuminate every corner of the workshop, make visual feel more comfortable, improve the working efficiency of the workers in the workshop.

Used 150W LED high bay light in workshop is a wise choice. 

The importance of heat dissipation for LED high bay light

Look from the luminous efficiency, LED high bay light is higher than fluorescent lamp, but even low power LED high bay light also needs a bigger heat sink to solve the problem of heat dissipation, and very hot to the touch.The same power of fluorescent feels never hot like this. Does anyone know what reason is this?

How to solve the problem of heat dissipation ? TEK Lighting tell you related issues about LED high bay light heat dissipation.

Why LED high bay light must be heat dissipation?

The reliability (life) of the LED high bay light  depends on the heat dissipation, so improve the level of heat dissipation is one of the key technologies.Mainly to solve the excess heat generated by the chip through the heat sink out, this is a very complex technical problems.So the heat dissipation problems cannot be ignored. Based on the limitations of current technology, we can only try to heat dissipation when using LED high bay light, because if heat dissipation is not good, will affect the service life of the LED high bay lights.

Radiator is use for LED high bay light heat dissipation, because the LED chip on the job, its environment temperature and the light rate is inversely proportional relationship , the higher the temperature, the light rate is lower, when the temperature reaching the highest temperature of the LED chip, the LEDs will spoil. So the the temperature for Life, droop, color temperature of LED high bay light has a direct relationship, in other words, radiator also determines the stand or fall of LED high bay light.

Most LED high bay light will adopt aluminum plate to heat dissipation, unfortunately the heat dissipation material also let a lot of "dirty" businessman use unqualified material and bad performance of aluminium materials to make aluminum substrate, it let the manufacturer to save the costing of the LED high bay light , but will cause light efficiency, life, light failure become very poor, so when choosing LED high bay light must pay attention to the heat dissipation problems.

TEK Lighting LED high bay light have 5 years warranty,quality is guaranteed,contract fulfillment rate was 100%.

LED high bay light is the best choice that  both economic and environmental protection

Responsible consumers know that we abuse the decades of our natural resources, and now we should take active measures, reduce resource waste, instead of the traditional high energy consumption, using LED lamps and lanterns which energy-saving and environmental protection , The choice of using LED high bay light, both economic and environmental protection. LED high bay light is a solid product, is reliable, high quality light source.

Although at present the price of LED high bay light is higher,the initial investment cost of buying LED high bay light is higher than traditional lamps and lanterns,but in the long run, is more energy saving and long lasting. LED high bay light is more brighter,more energy saving . Compared with traditional fluorescent tube, LED high bay light save electricity consumption bout 60%. fluorescent tube can lighting last about 8000 hours, and LED high bay lighting can last at least 50000 hours, and fluorescent tube is not environmental protection,because they contain mercury and other harmful substances. When dropped,they will cause serious environmental pollution.

commercial lighting using LED high bay light to replace  high pressure sodium lamp  is one of the most energy-efficient solutions, LED high bay light has low power consumption and a longer life cycle.100w LED high bay light brightness is equivalent to 250w HPSL. And LED high bay light can be recycled completely, does not contain any harmful or toxic substances.

Energy-saving era is coming, what are you waiting for, use the LED high bay light is the best choice, both economic and environmental protection. Using LED high bay light replace your traditional lamps and lanterns, not only save electricity, you also contribute to protect the earth ecology resources.

How to purchase LED high bay light and matters needing attention

As technology development, 100 w LED high bay light could replace 250 watts traditional industrial and mining lamp, more and more factories, toll station, large open area use LED high bay light, so using a huge number of correct purchasing excellent LED high bay light , will save cost.

We buy the LED high bay light for its long life, and the purpose that save electricity than traditional industrial and mining lamp, again speak  some of the procurement of LED high bay light;

1, Lighting brightness

First of all , you must determine your own lighting places demand when choosing lamps and lanterns, how many, how much power LED high bay light? Looking for the meet the requirements of the lighting lamps and lanterns, the brightness is too strong or too weak, will affect the user experience!If you don't know  know can consult others people, or we can provide lighting design.

2, Choose high quality LED high bay light

High-class power supply.  at the same time we must investigate power supply which lighting places provide ,   so you can decide whether to adopt constant pressure constant current controller, avoid because the  rectifier produce ower grid, along with the noise and light intensity is not stable, cause eye fatigue.

Aluminum alloy radiator.due to the calorific value of LED high bay light is big, need a good heat dissipation material.Generally use is aluminum alloy material, and the LED high bay light is much heavier than normal, structure must meet the requirements of the heat dissipation specification, ensure the service life of the light source, with LED high bay lighting shell, should choose to strengthen and environmental protection, high heat resistance materials! 

3,Choose a good LED high bay light manufacturers, quality guaranteed.

And the benefits of LED high bay light price is expensive , energy-saving effect is very good, when select LED high bay light, power supply is the key, and chip and  heat dissipation is good or bad relationship to the life of the lamp, suggestion choose a good manufacturer. 

TEK lighting production of lamps and lanterns have 5 years warranty,Our products are surely of standard quality and price concessions,we also improve incessant, many consumers have been well received.

What is about TEK Lighting LED high bay light quality?

TEK Lighting as a professional LED high bay light manufacturer for eight years , our led lamps and lanterns has the following advantages:

Energy-saving

Without changing the original lighting circuit, under the condition of the original illumination, Using TEK lighting retrofit led lighting products,compared with the traditional energy-saving lighting products, energy-saving rate up to 60%- 70%, which is based on the original and replacement of lighting lamps and lanterns of parameters such as power, using time, the local charge standard.

Long life
LED  high bay light to provide lighting for longer , about 10 times more than the traditional light bulb, TEK Lighting high-end product quality, the life of 50000 hours;Avoid every year the lamps and lanterns replacement and maintenance work , effectively save the purchasing cost and maintenance cost.

Durable and safety
LED high bay light is highly durable, because they are not made from filament;on the contrary, incandescent light bulbs, fluorescent tubes and these are easy to broken.

efficient
LED high bay light consume only 100watts , which can reach 250 w High pressure sodium lamp brightness.Compared to Metal Halide lamp can reduce your electricity bills 30-40% of the energy.

Protect eyesight
Stable and soft light with no stroboscopic, intercept ultraviolet ray, no harm of blue light, this is the traditional incandescent lamp, fluorescent lamp and other light sources do not have advantage, LED high bay lights is green, no pollution, is the best  work lighting products,24 uninterrupted time ;LED high bay light  also can combination of 85-268v voltage, lighting transformation using the LED high bay light, don't have to worry about voltage instability and flicker;

Which company do energy-saving transform is best?

Illumination energy conservation transformation to find who is available, TEK Lighting analysis for everyone.

It is understood that the general factory ，workshop is using high pressure sodium lamp or metal halide lamp, about 200-400w, day lighting time is long, high electricity bills each month, the traditional lamp life is short, often need to change, easy to bad the starter.The quantity of lamps and lanterns is big, the problem is big.Using 100 w LED high bay light can replace 250 w high pressure sodium lamp, and can have a comfortable environment with its eyes.

Actually  the best choice of lighting energy-saving transform  is using LED high bay light, energy-saving , long life, is worth to recommend, but the problem is to find who is better?Who is on lighting energy-saving renovation?You don't listen to me slowly explains.

There are a lot of illumination energy conservation service company, it is recommended that look for the big lighting factory inquiry, manufacturer general will give you make the energy saving retrofit scheme;

Do energy saving renovation is best to find the led high bay light manufacturers, because some of the trading company have no production product, take the goods from other places, several links that will increase the cost, looking for a manufacturer is practical;Or come to us,  we are professional manufacturer of LED lamps and lanterns, provide commercial lighting energy-saving renovation services;

The factory workshop lighting is an excellent way to enterprise cost savings, advice if your factory is to use  lamps and lanterns , advice buying LED high bay light, concrete factory  lighting energy saving retrofit scheme, please contact us!

Whether LED high bay light belongs to the lamps and lanterns that shield an eye?

The lamps and lanterns that shield an eye to protect eyesight, to reach the eyeshield must have three conditions:

The color temperature value of Lamps and lanterns  determines the degree of light is downy, too high and too low are not good, is suitable for 4000 k to 5200 k.LED high bay light, green and environmental protection, the real no stroboscopic, no ultraviolet light.

Traditional metal halide lamp exist stroboscopic and ultraviolet light may so that affect vision, LED high bay light as a green lighting products, compared to traditional fluorescent energy-saving lamps, can save energy about 50%.Their eye effect is absolutely no stroboscopic, no ultraviolet light.

LED high bay light can adjust the brightness, can need to move light, a variety of brightness can choose.

Someone will think LED high bay light look will be very dazzling, LED high bay light is very dazzling to eyes hurt?In fact any light look straight to hurt the eyes, so why to erthyphoria it?

TEK lighting LED high bay light manufacturers:  the biggest advantages of LED high bay light ar  longevity and energy- saving .Traditional light source compared with LED light source, LED high bay light have more advantages.

Apparel clothing factory workshop lighting energy saving retrofit scheme

Clothing is indispensable to People's Daily production, as people living standard rise, the demand for clothing is more and more big. some areas have advantages, as the garment industry competition is more and more big, the production management also tended to energy conservation and environmental protection, reduce investment, enhance competitive advantage.

The clothing factory clothing factory workshop major energy-consuming in sewing machine, iron and other equipment, boilers lighting lamps and lanterns and air conditioner, air conditioning is seasonal, usually air conditioning less than 6 months, except in addition to the clothing production equipment, lighting lamps and lanterns is also a large energy consumption.

Some large clothing factory clothing factory workshop, especially the two shifts of the factory, the lighting time not less than 20 hours, the use of LED corn lights can reduce 50% of the energy dissipation garment factory lighting, using LED corn light is a wise choice clothing factory clothing factory workshop,

The advantage of apparel clothing factory workshop lighting using LED corn lights

Clothing factory clothing factory workshop daily lighting using new LED corn light, 15 W LED corn bulb can effectively replace traditional fluorescent lamp (36 + 5) W, energy saving more than 65%, sharply reduce lighting electricity; And ordinary short life need to be replaced every year, energy-saving lamps and LED corn lights of quality of life can be up to 50000 hours, 5 years without changing the lamp;

The cost of the LED corn light is higher than ordinary energy-saving lamps and lanterns, how to do?Don't worry, it will come back in electricity .

LED high bay light can be used for lighting factories use and advantages

LED high bay lights are appropriate in the workshop?

1, Generally All in all sum up, the price of LED high bay light is several times than traditional lamps and lanterns, for some small factory workshop, illumination time is short, with the ordinary energy-saving lamps.

2, then some big the factory workshop of large area, especially the factory two shifts, illumination time not less than 20 hours, then LED high bay light is  perfect, save electricity is very obvious.

The advantage of LED application in factory workshop.

You can say that LED high bay light energy-saving 60% than common fluorescent lamp, than energy-saving lamp power saving 40% is possible .A 100w LED high bay light can replace traditional 250 w HPSL, as LED high bay lights product price also will be more and more populist, LED high bay light will be widely used in the future, for the country contribute to promote energy conservation and emissions reduction goal.

The common sense of LED high bay light

The power of LED high bay light commonly big and used widely, such as warehouse, storage room, garage and some industrial applications , due to long life, small energy consumption, and no mercury, no radiation, is always popular with people.

LED high bay light of choose and buy should pay attention to the following a few simple matters

1, colour must to coordinate, LED high bay light appear glare after avoid purchasing back, the light is downy, uniform brightness, effectively avoid after long time use, lead to construction personnel in eye fatigue.

2, special occasions, such as the coal industry and other inflammable and explosive area should choose the highest explosion-proof grade. TEK LED high bay light can used in these place , It is waterproof and dustproof,easy to clean.

3, LED high bay light best to use the high strength alloy enclosure, the lamps and lanterns to fight against powerful collision or impact, to ensure the safety of life.

LED high bay light construction should pay attention to the following items:

1, reasonable distribution the position of lamps and lanterns, achieve reasonable light distribution, such as high brightness, can make the person feel the space is larger, the opposite is man-eater flower feel depressed easily.

2, for the rich atmosphere of lighting area, should reduce the lighting waste, the construction area should be reasonable distribution LED high bay light power and choice.

The feature of 200W LED high bay lighting

200w LED high bay light has three protection: : waterproof, dustproof, antiseptic.Special anti-oxidation corrosion materials and silica gel seal ring is used to realize the protection requirements of lamps and lanterns.Due to some 200 w LED high bay lights has three characteristics, make it suitable for outdoor damp, dust under severe environment.Such as industrial land, parking lot, swimming pool, kitchen, food manufacturers and tunnel etc.

What are the characteristics of 200w LED high bay light?

1, the luminous efficiency and energy saving
High photosynthetic efficiency, 200 w LED high bay light about 80000 hours on average, eliminating the frequent replacement of lamps and lanterns of troubles and inconvenience.


2, professional design
Homogeneous soft light projection, especially suitable for all kinds of high top, high canopy of lighting fixtures.


3, protection grade
Shell protection grade IP65, WF2, shell corrosion never, never rust.


4, shockproof performance is good
Use of lightweight alloy material and high-tech spraying technology, the shell never rust, never corrosion.Lamp body internal through double damping structure and material, can be in all kinds of high frequency, strong vibration place to work for a long time.


5, the lamp body heat dissipation is good
Lamps and lanterns of overall low temperature, good heat dissipation, can reduce error probability.


6, high power factor
With high power factor electronic ballast or low efficiency, no noise, long life, energy-saving inductance ballasts, energy-saving effect is better.

The prospect of LED corn light application in the field of industrial lighting

With the development of the society, all kinds of industrial buildings, such as bamboo shoots emerge, in order to ensure the smooth progress of production and inspection workers, will need to configure corresponding in the workshop lighting lamps and lanterns to light workers to the demand.Industrial lighting emphasizes the LED high bay light of features.In the application in the field of industrial lighting, LED lighting lamps and lanterns need to pay attention to its function, the environment is complex and diverse choice of lamps and lanterns.


LED high bay light use mostly high-power lamp beads as the main light source, it has high thermal conductivity, light failure is small, the advantages of good color rendering, no ghosting.LED high bay light has the advantages of green pollution-free, its color is very good, for any entity material color rendering realistic, eliminates the past lighting gives people the color error, improve the work efficiency of the workers.


LED high bay light using power is larger, the very unique heat dissipation design, and compared with electrical box clever union, effective spread heat diffusion, which might reduce the temperature in the LED lights, to ensure that the service life of the lamp body.Banner staff in the surface coated with a layer of anti-corrosion treatment of lamps and lanterns, also played the appearance of beautiful effect.LED high bay light use scope is broad, tend to use in the warehouse, the empty courtyard, freight yard, storage or large prison, etc., its long service life, low consumption of energy.One of the lamps and lanterns is by far the most widely used.


Actually, the LED high bay light is the most obvious effect of energy conservation, generally USES the quality is very good chip, equipped with efficient power, so that when it compared with the same brightness of lamps and lanterns, can save seventy-five percent of energy consumption.LED high bay light special chip, make its service life is long, life is about fifty thousand hours.In addition, the LED high bay green pollution-free, excluding special chemicals, users will not cause the harm of the body and the environment pollution and so on.Some users will be to deal with the special appearance of the LED high bay lighting, use it for decoration, the effect is good, with its simple installation, use range is more extensive.

LED corn light is welcomed with workshop

LED corn light has been able to get the welcome of people from all walks of life, the main reason is the ability to continuously innovation and development, and the reasonable security factors, therefore is loved by everyone.So in the present society developing continuously, can better adapt to the current trend, this is the lamps and lanterns, because our country is also aspects of energy saving lamps and lanterns, so the production of LED technology, will be able to welcome and loved by all of us.

LED corn light can also in unceasing progress, have a best development technology, because of our country in the development of lamps and lanterns, have adopted the international advanced level, thus to obtain recognition and love, can also constantly love by you, so also has a certain development advantages, so in our country's future career, more able to show is also vigorously mining of lamps and lanterns, including the use of safety performance of lamps and lanterns, etc as a whole.

LED corn light on the design, to avoid the bad condition of traditional lamps and lanterns, because he in the design of traditional lamps and lanterns, always has some not convenient use effect, short life, for example, or is the brightness of the light, there are still some other function of light can achieve using a standard, if an enterprise often replace the lamps and lanterns, so also is a kind of waste of resources and capital input, so use this kind of lamps and lanterns, can better guarantee the use effect of everyone,

And LED corn light on the application in the production workshop, the enterprise for the factory also saves a lot of spending, saving electricity was above 60% than traditional lighting, which is to be reckoned with.

The main I think is the quality of the lamps and lanterns, because the quality is good to receive your recognition, can also constantly popular with many people, so is everyone favorite and the kind of progress plan, in the society, can actually become a kind of power, has also become a trusted application technology level.Future development, will continue to try to maintain and create a better tomorrow.

LED corn light is integration with our life

LED as light source used in lighting lamps and lanterns, only ten years, has great development, at present, there are many types of LED lighting lamps and lanterns, product constantly updated. LED corn light is a high visibility , best-selling indoor LED lamps and lanterns on the market in 2016.

LED corn light is a kind of led lamps and lanterns, because led light Angle is 120 degrees, considering the luminous uniform, LED corn light is designed to 360 degrees, its shape like corn cob, called led corn light. Lamp body is small, convenient installation;Modern design, sophisticated technology,  give full play to the led light source energy conservation and environmental protection, do not produce any waste.

Because incandescent lamp and electronic energy-saving lamps in People's Daily use still occupies a very high proportion, in order to reduce waste, LED corn light manufacturers must be developed LED corn light products which in accordance with the existing interface and habits of the people, make people don't need to replace the original traditional base of lamps and lanterns and lines can be used under the condition of a new generation of LED lighting products, LED corn light thus arises at the historic moment.

LED corn light using the existing way of interface, namely, screw, jack way (E14 / E26 / E27 / E39 / E40, B22, G23 / g24), and even to accord with the habits of people adopted as incandescent lamp, fluorescent lamp holder.

LED panel light to enter the Chinese railway lighting market

Electric light source development innovation, has experienced the incandescent lamp, halogen lamp, fluorescent lamp, now in the era of LED light source.today led industry has reached a stage of practical application, so the characteristics of LED technological innovation should be more play, play to the role of the energy-saving lighting, the subway as an important space public activities over the past two years, in the building of the lighting, the most subway station used LED panel light lighting scheme, not only can save a lot of electricity and a lot of copper, but also to ensure the quality of lighting, at the same time save a lot of the cost of maintenance.

In 2014, China began to in the construction of the subway, generally have preferred led panel lights for lighting, in the recent news, shenzhen to improve crowded subway line 1,  ready to launch a new car, and in the interior lighting using  led panel lights, relative to the conventional lighting power saving more than 30%.Using LED panel lights, basic can reduce energy consumption by up to 50% a year.

Because all the year round in the underground, subway control lamp has a high requirement.It requires not only power saving, high brightness, long life, but also ensure uninterrupted lighting.However, commonly used incandescent lamp, fluorescent lamp, high-pressure sodium lamp and so on all has certain defects, in contrast, LED panel light with environmental protection, energy saving, long life, high light efficiency, no radiation and other characteristics, prolong service life and reducing the energy consumption greatly.

And LED panel light to strong vibration resistance is very suitable for the characteristics of the metro operation environment, can be  without replacement in 6,7years, nearly 50% higher than common fluorescent lamp.Therefore, the LED panel light has become the best green lighting lamps and lanterns.

Quality is the key element of LED corn light into the market

Energy conservation and environmental protection is a trend in today's society, as governments continue to guide and promote, save electricity, energy saving, environmentally friendly LED lighting products by the market, LED corn light become investment hot, a list of brands and factories at home and abroad have sprung up in large and small. Since 2014, global ban incandescent lamp, incandescent lamp will gradually withdraw from the historical stage, LED corn light price continue to fall, prices have already can be accepted by the mass market.


PK between enterprises market, is not around the product quality, price, etc., but the price war.As is known to all, mass production is the key to reduce costs, in the case of can't realize the mass production, just to lower the price of products, product quality will be difficult to guarantee.We can foresee, LED corn light market confidence crisis is approaching.


In general, the product is the lifeblood of enterprises, and the quality is the basis of enterprise survival and development.Although formulated and issued the relevant standards of the state, to solve the lack of industry standards and product quality to provide the standard basis, but as a result of LED corn light industrial chain which involves many links, some related standards remains to be progress and improve.


Confusion for LED corn light industry, LED industry standard is missing, there is no standard cannot judge the quality.LED corn lamp lighting industry development is rapid, relatively standard from set to enacted process longer, many experts in the industry, LED corn light standards can't keep up with the speed of industrial development.Some enterprises plaint standards for a long time, some even outdated standards, instead of limiting the development speed and scale of the industry, and myopic type enterprises want to get a quick, before the standard is not unified fish in troubled waters, disrupted the market order, has affected the healthy and orderly development of LED lighting industry.


Many lighting companies are the reappearance, hope to perfect the national standard, guide LED corn light development.However, there are some firms think that is better than national standards, industry standard industry standard as the enterprise standard, national standard may become a hotbed of protect the weak.Whether the national standard is the touchstone of for the LED corn light!

LED corn light development, innovation is the only way out

With the deepening development of science and technology, the LED lamps and lanterns, as a kind of high-tech products gradually into the mainstream, many consumers began to accept the LED lamps and lanterns to bring life change, but for many consumers, they also not know what are the specific advantages of LED corn light, let TEK lighting to take you break down.


LED corn light is widely applied to textile, the toll station, gas stations, construction sites, stadiums and other places of need to work at night; For mine, workshop, workshop, warehouse and large supermarket such as indoor daylighting mismatching workplace, often see the figure of high power LED corn light. Same LED white light LED corn light source, the shell, the user can choose according to their own needs, the main shell material is aluminum alloy profiles.
 

LED lamps and lanterns, energy conservation and environmental protection performance is known, LED corn light energy function is also obvious, its power consumption is only one 5 of the normal sodium lamp power, greatly save the energy, the same application of luminescence brightness, LED corn light can accept 80% energy, particularly in line with the state advocates green low carbon environmental protection concept.


Road lighting is an important part of city lighting, often USES traditional street lamps, high pressure sodium lamp 360 degrees, the light loss big shortcoming caused a huge waste of energy.At present, the global environment worsening, all countries in the development of clean energy.And along with the rapid growth of the national economy, the contradiction between supply and demand of energy in our country, start there is a serious shortage of electricity supply situation, saving energy that is an urgent need to solve the problem.Therefore, the development of new type of high efficiency, energy saving, long life, high color rendering index, environmentally friendly LED corn light on urban lighting energy saving has great significance.


LED corn light without junctions, have excellent explosion-proof function, various kinds of inflammable and explosive environment of industrial and mining use can safely use, such as lamp chimney body shell made of high-quality aluminum alloy plate has good rustproof function, suitable for use in harsh chemical environments.

Eight tips to distinguish LED corn light

Configure virtual standard

LED corn light is also sell like hot cakes with price lower profits, in the fierce competition also LED to many businesses began to jerry qi product parameters, it is also the customer has repeatedly than price, require low price, is also related to the practice of a few manufacturer.


2. Counterfeit chips

LED corn light is the most core chip, directly determine the performance of lamps and lanterns!With customer's unprofessional some undesirable businessman, however, from the cost of the above consideration, using low price chip, make customer buy the low quality of the product with high price caused a direct economic loss, and cause serious quality hidden trouble to LED corn lights.


3. Copper wire as gold thread

Many LED manufacturers trying to develop such as copper alloy, gold silvering alloy wire, silver alloy wire to replace expensive gold thread.Although these alternative is better than that of gold thread on certain features, but poor in chemical stability but many, such as silver and gold silvering alloy wire is vulnerable to sulfur corrosion/chloride/bromide, easy oxidation of sulfide copper wire.For similar to suction breathable sponge encapsulation of silica gel, these alternatives to make wire bonding are more susceptible to chemical corrosion, the reliability of the light source is reduced, use time grew, LED lamp bead are more likely to break the dead light.


4. The lamp light distribution system design is not reasonable
Optical design, if the lamp light distribution system design is unreasonable, lighting effect is not ideal.Tests will appear "under the lamp light", "light black", "zebra crossing", and "uneven illumination", "yellow" and so on.


5. Bad heat dissipation design
Thermal design, LED chip junction temperature of PN junction every 10 degrees, the service life of semiconductor devices will be faster.Due to the LED corn light brightness demand is high, the use environment is harsh, if the cooling solution is not good, can rapidly lead to the LED aging, reduced stability.


6. Power failure
Drive power supply, power supply if there is failure, the process of testing and inspection, there will be a "whole lights" and "damage", "individual die LED lamp bead light", "the whole lights flashing virtual" phenomenon.

7. Security failure
Security issues is also worth serious attention: street light there is no power leakage protection;Street lamp ballasts quality shoddy;Circuit breaker for sensitivity test revision, rated tripping current selection is too large;Main cable metal sheath is used as the PE total process is complex, low reliability;IP waterproof and dustproof level is too low.

8. If there is harmful to the light source of lamps and lanterns
LED light source of black is each big LED company often encounter problems.Most of the material in the lamps and lanterns to be affecting the service life of the light source material.

The changes of three kinds of lamp, LED corn light successfully replaced them

Lighting lamp is indispensable things in daily life.People's Daily use of energy-saving lamps are replaced by LED corn light gradually, energy-saving lamp Which has been national vigorously promote replace incandescent is slowly withdraw from the market.


Environmental protection concept updating, small energy-saving lamps are also experiencing three generations of change. Behind the recycling problems worthy of attention, many also understand a little energy-saving light bulbs, to exert more power for green life.


Energy-saving lamps also called fluorescent lamps, because of its efficient and is seen as a substitute for traditional incandescent bulbs.It mainly comes from improvement of environmental awareness.Before lighting system only pay attention to quantity, a long period of time have been gradually toward the delicate, exquisite energy-saving effect.Because of lighting technology and the wide use of lighting fixtures, make people living standard rise generally, growing surge in demand for lighting equipment, also makes the power consumption, and so began attaches great importance to the development of high efficiency, high quality LED corn light.


With growing calls for energy conservation and emissions reduction, environmental protection consciousness is becoming more and more popular. LED corn light in recent years, because not cause pollution, high efficiency is causing social attention.Now people are starting to use LED corn lamp to replace the energy-saving lamps.


LED corn light is considered can completely solve the problem of mercury pollution of energy-saving lamps , because do not contain mercury, but also can save 80% of the electricity, the service life of eight to ten years.

LED high bay light is widely used, won unanimous praise from all walks of life

Domestic leading UFO LED high bay light enterprise TEK lighting have made brilliant achievements in the aspect of energy conservation and environmental protection, energy-saving effect of gas station increased 69% immediately , won unanimous praise from all walks of life.



The original gas station to adopt 400 w metal halide lamp used for lighting, use TEK lighting 150w UFO LED high bay light to replace the original 16 sets of metal halide lamp.Reconstruction is completed, only 150 w UFO LED high bay light illumination has more than 400 w metal halide lamp, high brightness, no glare, energy saving ratio increased by 69%, improve a highly integral illume environment.


Gas station is a public service, 24-hour service, so the gas station has a high requirement on the lighting, lighting in addition to  meet the requirements of intensity of illumination at night , but also have to ensure safety, don't drop impact to the gas station of oil and gas environment.


TEK lighting said, after the transformation of the gas station is not only good illumination, luminous evenly lit, and on the security, the UFO LED high bay light has strong heat dissipation structure design, also can guarantee no adverse impact on the environment.At the same time,  unique advantages let the customer enjoy high quality light source and reduces the maintenance cost, a multi-effect input-output, fully staffed.


Using TEK lighting UFO LED high bay light, the gas station on the hardware is equipped with customers consistent praise.Night, UFO LED high bay light to bring customers enjoy new, beautiful and practical.This series lamps and lanterns is quite popular in domestic and foreign market, the market absolute mainstream, is widely used in factories, sports venues, logistics centers, gas stations and other public areas of the large space based lighting places.

Different vision, manufacturing by the latest LED corn light

Adopt LEDs manufactured LED corn lights have a long life, high brightness, the projection distance is far and other significant advantages, has become optimization source of a widespread alternative metal halogen lamp and high pressure sodium lamp light , to become the next generation of the trend of  factory lamp.

From the actual road lighting , not only vision , brightness, and the projection distance, LED corn light is obviously superior to the metal halide lamp and high pressure sodium lamp, the life of the former is the latter several times.

Although LED corn lamp is a new lighting source, in terms of lighting market, in order to save time and money while using the original lamp body system, so in design with the appearance of LED corn lights, fixed size and interface, brightness and luminous flux, should try to be consistent with the metal halogen lamp and high pressure sodium lamp. As our LED corn light can be directly mounted in the original interface, its socket E26 / E27 / E39 / E40, installation is convenient, rapid concise.


When alternative metal halogen lamp and high pressure sodium lamp, there is no need to make big changes on the lamp body. As a new alternative light sources, the use of LED corn light must bring a new experience to the user, not only on the life and reliability have improved significantly, and without any increase in even at the same time of reducing glare, can significantly increase the ground illumination and projection distance.

UFO LED high bay light is used in huge warehouse, 75% energy saving

UFO LED high bay light compared with the traditional metal halide lamp and high pressure sodium lamp has obvious advantages, more than 75% energy saving, service life is almost 10 times than traditional industrial lamp, and selection of  color temperature , no light pollution and completely green.

100 - 240 w UFO LED high bay lights all alternative under 600 w metal halide lamp, and remarkable superiority.Warehouse lighting requirement is bright and clear, no glare, no ghosting.Using the UFO LED high bay light is the most scientific choice: LED lamps and lanterns in power saving half of the cases, its brightness and clarity is better than traditional metal halide lamp, mercury lamp, fluorescent lamp.UFO LED high bay lights replace traditional lighting has become an irreversible trend.
 

1, TEK lighting UFO LED high bay light use most famous original CREE  as the light source, which guarantees the quality from the source.

2, using the overall heat dissipation structure, common industrial lamp only through the radiator to heat, effect is not ideal when the power is large , the radiator of UFO LED high bay light is combine with and the entire lamp body , greatly improving the cooling efficiency.Junction temperature can be controlled between 80-85 degrees.According to the test report of CREE show that service life is more than 50000 hours when junction temperature at 85 degrees.

3, UFO LED high bay light use the high quality Mean Well power, in order to ensure the stability of the power supply and service life.


4，UFO LED high bay light adopts nano coating materials, greatly improves the reflectivity of light, and makes more uniform distribution of light spot.

LED corn light is prepared for industry

LED corn light can meet the requirements of work at night. Is not only in the night, a lot of visual task because it is a indoor operation, if the lighting level is insufficient, lack of visual features will cause error rate increase or reduced speed. Using LED corn lamp can ensure good visual characteristics, increase efficiency of operations .Ultra high color rendering index in relatively dim environment, also can improve the light efficiency effectively.

LED corn light can meet the needs of the brightness, at the same time give person with comfortable vision. traditional sodium lamp start need preheating, if without electricity, you need to cooling and preheating can start; Sodium lamp current harmonic;Screeched current.Bulb surface temperature as high as 360 ℃, under the sodium lamp obviously feel the environment temperature;Low color, light color deviation, visual effect is poor;Stroboscopic effect harm is serious, directly to the naked eye observation of small objects, dazzling light, depressive environment.Obviously, a reassuring in sodium lamp light can not work, reduce the working efficiency.Using LED corn light completely don't have to worry about.

LED corn light meet energy saving, low carbon and environmental protection requirements.It is well known that the energy consumption is mainly concentrated in the industrial industry.Enterprise has more than 20% energy saving potential, due to lack of funding and advisory services of energy conservation, heavy energy costs make the enterprise cost is greatly increased, not only make the power supply tension, pollute our living environment at the same time.

 Why do warehouse need LED corn light ?

LED corn light with new type of high efficiency, energy saving, long life, up to global energy saving low carbon and environmental protection requirements, LED corn light is an important part in urban industrial lamps and lanterns,traditional mining lamp often use 250 w, 400 w metal halide lamp, caused a huge waste of energy, LED corn light just make up for this defect. Therefore, LED corn light is closely related to industrial production.


LED corn light system with directional light, low power consumption, high seismic capacity, such as green environmental protection advantages gradually into people's horizons, LED corn light replace traditional light source and become a new generation of energy-saving light source, therefore, LED corn light will be the energy saving renovation choice of traditional large industrial workshop, theatres, cinemas, large commercial shopping centers, warehouses and other places lighting.

Because environmental protection and energy saving features of LED corn light compared with general incandescent bulbs, has considerable advantages to promote people to pay close attention to  the development and sales of LED corn light, LED corn light power from 80 w to 200 w, the input voltage of AC85-265 v, 50-60 hz, the work efficiency of lamps and lanterns at 92% and luminous flux is 130 lm/w.

Because of the light is downy and the brightness is also very good, can be applied in many warehouses lighting occasions , uniform illumination, people in LED corn lighting range will not feel the fatigue of the eye, so, LED corn light is the most suitable for large, medium and small warehouse lighting use.

The characteristics analysis of the LED high bay light , Watching you will understand why people like LED high bay light

LED high bay light has multiple strengths, and thus is widely used in workshop, factories, mines, shipyards, gas stations, large supermarket, gym and so on.Detailed analysis of the characteristics of the LED high bay light includes the following aspects:

LED high bay light technology has improve base on predecessors, adopt fan in wind cooling principle, can fully take internal heat flow discharge in time, thus reducing its temperature, ensure the cooling requirement and service life of the LED high bay light source,and its surface though anodized anti-corrosion treatment, compact structure and beautiful. LED high bay light used the acicular radiator cooling efficiency than conventional flake radiator has the substantial progress, can make the LED junction temperature lower 15 ℃ than the ordinary radiators.


LED high bay light has the characteristic of long life, its exclusive chip technology fully guarantee the service life of the light source.radiator combined with lamp shell integration design, can guarantee the service life .

LED high bay light unique group chip integrated single-mode light design, selection of high brightness chip, the encapsulation of high power LED (80-1000W) as a light source, its high thermal conductivity, light failure is small, light color purity, no ghosting phenomenon.Good color, trousers for color rendering more closely, a kind of light color optional, can be satisfied with different environments, eliminating the traditional lamps and lanterns of color temperature on the high side or low depressive mood, improve the workers work efficiency.

LED high bay light using single chip integrated high power LED light source is equipped with more efficient power, equal brightness than traditional energy-saving lamps and lanterns 75%.

LED high bay light also have green pollution-free advantages, LED high bay light don’t contain aluminum, mercury and other pollution elements, so not to cause any pollution to the environment.

Before buying LED high bay light , you must to know these things

LED high bay light is produce homework area lamps and lanterns which is used in factory, mine . in addition to the outside environment usually use lighting, LED high bay light also used in the special environment and prevent erosion , and LED high bay light used in some large in high-rise buildings.

LED as a new energy saving lamps and lanterns, in the process of lighting is converting 30-40% of its electricity into light, all the rest  converted into heat energy.And the service life of LED lamps and lanterns and quality relation with temperature close intimacy, lamp beads, shell temperature, cooling temperature will be related to the LED illumination and quality of life.

In order to be meet different visual, LED high bay light reflector should be able to produce various width degree light distribution. Suitable for large area, vertical or near vertical face of the workplace.For tall buildings or requires a separate lighting can contact LED high bay light manufacture to custom-made.

 
In dusty, wet and other places of poor environment premise of medium and long-term work, LED high bay light in structure design, casing and reflector has special requirements.Considering the production sites in the inevitable shake, LED high bay light used prevent loose lamp holder, and so on.Outdoor LED high bay light drive power supply should consider the function of waterproof, moistureproof, its shell is not easy to aging in place to ensure that the life of the drive power supply is adaptive with LED high bay light life.

There are many LED high bay light fixed way.General lighting has top, embedded, lifting (with straight or chain) and absorption wall form, etc.Portable local lighting equipped with corresponding hooks, handle, pinch, etc.;Fixed local lighting with screw or fixed firmly locked in work on the machine.

How much to pay for upgrading a warehouse lighting ？

Why upgrade warehouse lighting

When you have idea to starting replacement for your existing warehouse light with a energy saving lights, that means you aware of your existing light fittings can not provide enough brightness in your working area and costing your thousands of extra dollars every year with an inefficient and poor life HID lamps.

Starting to retrofit or replacement old inefficient lights in the warehouse doesn’t to be expensive or complicated. In fact, more and more people are starting to use dimming LED high bay lights replacing HID and other energy saving lamps, such as CFL.

“How much need to pay for upgrading a warehouse lighting?” Most warehouse owners concerned about the cost of retrofit a warehouse lighting. 

Starting to retrofit or replacement old inefficient lights in the warehouse doesn’t to be expensive or complicated. In fact, more and more people are starting to use dimming LED high bay lights replacing HID and other energy saving lamps, such as CFL. 

The Benefits:

1. Provide a quick return on investment—Use LED retrofit light to replacement for existing HID low bay or high bay, carbon and electricity savings can pay for the new LED light fixtures in 6-18 months. 
2. Improve lighting level in working area—dimming LED high bay lights provides a high lumen output 125 LPW., excellent color rendering, no flick, environmental friendly.
3. Maintenance free—dimming LED high bay lights provide 5 years warranty

The Solution:

There are so many dimming LED high bay lights available in the markets, you may not easy to choose a replacement LED lighting for your warehouse. And you may try few samples from EBay or Amazon, but it always died in few months, or industrial lights do not have ground wire, it very dangerous. You may start to worry about the lifespan of new light source, and give up to upgrading your warehouse to an efficient light, use back to metal halide, high pressure sodium lamp or mercury vapor lamp and CFL. Obviously, it is not a wise decision. Because energy saving industrial LED lighting provides a guaranteed financial return 6-12 months is typical.

How to choose the right efficient dimming LED high bay lights for your warehouse? There are two situations:

One, keep the existing lighting fixture, use LED bulb replacement for HID lamp. Typical warehouse 

Two, Replacement for whole light fixture, simply and fast replacement.

 A lot of customer tell me that “I want to keep my existing lighting fixtures, I do not want to replacement the whole lighting fixture. Okay, we talking about the first solution which is use LED replacement bulb in existing lighting fixture. Typical warehouse lighting fixtures are low bay, high bay and canopy lighting fixtures with SON-high pressure sodium, metal halide, mercury vapor, or halogen lamp. 

Harizontal installation--Low Bay Light Fixture

Vertical installation--High Bay Light Fixture

LED warehouse lights replace 250Watts and 400Watts HID Low/High Bay fixture on one-for-one basis.

Upgrading your warehouse lighting for no cost, the utility bill savings can pay for the new LED lighting fixtures. Do you need a free lighting solution to cut down 60% or more electricity bills of your warehouse? Call us or send an email now.

LED high bay light maintenance method

Does LED high bay light need maintenance? How should maintain?As one of the family of LED lamps and lanterns, the LED high bay light in industry, the use is very frequent.Its safety and effect line, get the favor by major industrial enterprises. Although the life of the LED lamps and lanterns is very long, but if you can do a good job in the maintenance can increase its service life.
 
How to do a good job of science maintenance of LED high bay light ?
 
1, buy back after the lamps and lanterns, don't busy installation, read the installation instructions carefully, and then follow the installation instructions in accordance with LED high bay light, otherwise there may be dangerous;
 
2 don't change the structure of lamps and lanterns in the cleaning maintenance, also don't change the parts. After maintenance, should install lamps and lanterns is good according to the sample, don't packing, wrong parts;
 
3, when using lamps do not frequently switch, although the number of LED high bay light switch resistance is common fluorescent lamp of about 18 times, but still too frequently will influence electronic components inside the LED high bay light life, thus affecting the service life of lamps and lanterns;
 
 

 
4, in the end, LED high bay light had better do not used water cleaning, as long as can wipe with dry dishcloth touch water, dry, if accidentally run into water to try to avoid by all means after turn on the light immediately with a damp cloth to wipe.

How to reasonably choose the LED high bay light factory?

How to reasonably choose the LED high bay light factory? In our country, LED market is not normative, result in inferior products on the market, the enterprise in order to obtain huge profits, in the production of products, the choice of inferior material, rough process, only immediate interests, regardless of the long-term development, the market is more and more chaos.In the market for the product quality is uneven, users when the choose and buy, do not know how to choose.Choose qualified, but also good;Choose to unqualified, not only a waste of money, also pose a safety hazard.Therefore, when choosing LED high bay light products, need to rational to choose manufacturer.
 
What kind of LED high bay light manufacturer is reasonable?
 
First of all, the products must have national certification, the quality must be qualified, need to have a certain strength.As we all know, LED products are high-tech products, the production process needs to precise calculation, need to do a good job in every step of the otherwise produced products, only inferior or shoddy.We are choose LED high bay light must to take a closer look at, whether the certificate is complete.

 
Second, the LED high bay light manufacturers need to have good prestige.What is credit?Credibility is a kind of guarantee.No matter what industry enterprises, if credibility is bad, believe that users will not choose.Credibility in the minds of users, is a measure of a company's comprehensive strength of an important factor, is whether the user of the enterprise.The higher the credibility that enterprise high recognition rate of the customers.Choose this enterprise's product, it is guaranteed.
 
Finally, the LED high bay light manufacturers need to have good reputation. Where word of mouth come from?From users in the "heart", or the good word of mouth, is each enterprise, all want to do it.Because good word of mouth, represents the recognized by users, users are loyal to the enterprise.And good reputation, also is the ultimate weapon to attract new users.Has a good reputation and don't have good public praise of the two companies, I think most consumers will choose to have a good word of mouth.
 
When choosing LED high bay light manufacturers, need reasonable to choose.Manufacturers the most basic need to have more than three points: products are national certification, enterprises have good reputation, has a good reputation.Only with the above three companies, products, users can rest assured the choose .

How to improve UFO LED high bay light manufacturer public praise in the market ?

UFO LED high bay light market scale is bigger and bigger, large and small manufacturers springing up, competition is more and more big. TEK lighting as a member of the UFO LED high bay light manufacturers, how to promote the market reputation, increase the competitiveness of the UFO LED high bay light enterprises, and become the urgent matter.Only promote the competitiveness of the enterprise's reputation, in the future, to get a bigger share of the market. How to improve enterprise's reputation?
 
Improve enterprise reputation is the most important core users, only to achieve the customer satisfaction, to get the user's recognition, improve customer loyalty, and increase word of mouth. People-oriented, the development of UFO LED high bay light enterprises, the long-term development, the core factors are indispensable.
 
Can improve UFO LED high bay light enterprise reputation, starting from the service.Impression is good service, to the user is always good, according to the present market situation, the service is a big share, whether it's that kind of industry, complete service, retain customers, is a top priority.To do well the service, first of all, good communication skills is a must, communication can reduce the distance of each other, to get to know each other, to know the needs of users, so as to targeted services, more profound impression for the user.Was impressed by the user, the transaction will increase the probability of recognized by the user's opportunity is big.User acceptance, is an effective way to improve public praise.
 
Improve UFO LED high bay light enterprise reputation, product quality is the foundation.From the source said the source, after all, is the product of the market, the root of the enterprise and product, product do bad, no matter how your business reputation, is like a castle in the air, water, there is a fluctuation, disappear us, is not for a long time.Under the premise of getting the product, and then to the other;Only under the premise of getting the product, or to the other.This can be the basis of the UFO LED high bay light enterprise long-term development, that is the basis of loyalty of the customers, that is the basis of enterprise source of word of mouth.

Why so trustworthy LED high bay light ?

In the country's economic transition, the traditional products in use is eliminated, slowly by reform and innovation of new technology products are widely used step by step.And LED is one of gradually replace traditional incandescent lamp , a lot of LED products, especially in recent years, such as the LED high bay light, the LED corn lamp, today we want to say is a new type of LED high bay light, so the new LED high bay light than old-style lamp , what aspects do improved and adjusted ?


First , LED high bay light lighting effect better on the vision
Is composed of light emitting diode, LED accurate light distribution with high purity aluminum reflector, light weak light down to transform in different conditions, make every corner can be illuminate, irradiation range is very wide, spectrum in the visible area, intensity of illumination is very uniform, the light is very soft, not dazzling, to a certain extent, can also slow down the staff with the fatigue of the eye.


Second, the LED high bay light radiation capability further solution
LED high bay light quality is good key to see the heat dissipation is good, the heat dissipation is good key see heat dissipation material quality is good, now and in the future the LED heat dissipation base webmaster if pure aluminum, pure copper and copper aluminum combination as the main radiator, the heat dissipation of the material base board size precision, smaller size, more fine, leading the future development trend of LED high bay light.


Three, LED high bay light, explosion-proof structure, upgrade security upgrade again
Green environmental led solid-state light source, adopt the unique design of explosion-proof structure on the surface of the explosive gas temperature limits, need to make the lighting temperature of surface temperature is less than the minimum, in work safely under explosive and inflamable conditions.

What kind of work need to be prepare when install LED high bay light ?

Faced with more severe working environment to the normal work ,people have to introduce LED high bay light to facilitate people's work. LED high bay light actually means used in factory, it can provide basic working environment for people, such a light case, people can have a very normal for their own work.


To use LED high bay light has key problem is the installation work, in the installation in order to be able to achieve a better use effect, so naturally we also need to know how to do a good job of installing it.


Installation site selection is a problem, we first need to consider the installation site of choice will directly affect its lighting effect, so naturally we will have to need to pay attention to the problem of the site selection, a suitable venue is the primary choice in the installation.


In choosing a good site, we also need to do the correct install  LED high bay light, to say the correct installation or need our very bother, so naturally we also need to be more careful to do the work, such ability can successfully complete the installation work of light at the end.

When we are in the final to do a good job of choosing the lamp installation site, and installed after LED high bay light in the correct way, we can use the normal lamp, then we can also very normal in working state, can say this is very necessary for us.

About LED high bay light of waterproof and dustproof

Waterproof and dustproof LED high bay light leaking, generally there are several reasons for these cause,
 

1: itself has something wrong with the waterproof structure design, that are general shell on the market, that is general mode, the manufacturer only care about quantity, didn't pay attention to the details of the waterproof, also is the inside of the waterproof ring and structure has question.
 
2: production technology. If LED high bay light has a layer of thin fog as vapour, this kind of situation in the production of lamps and lanterns have a lot of wet steam, the glass and the inside of the sealing ring in combination with well wet steam, and you won't come to work as a whole, and the glass is lower than the temperature of the lamp body, the physical principle of the water vapor lamp body solidification on the glass in the glass with a layer of fog, but the light in the daytime cooling and gone steam fog, so a lot of people very upset, in the evening fog influence light effect and the Angle . 
 

Someone asked how did TEK waterproof and dustproof LED high bay light is waterproof ?

Waterproof and dustproof TEK LED high bay light with AC220V power, in view of the above two point leakage reasons, one of our structure is designed by myself, To eliminate the leakage, and second is when we in the production of cover glass, our lamp is operating at high temperature, wet water on the lamp body, as far as possible to reduce false vacuum, that is, won't produce the fog.

What is the distinguishing feature of the 0-10V LED high bay light?

Industrial lamp lighting is closely related to industrial production, the 0-10V LED high bay light is a better performance lamps and lanterns, 0-10V LED high bay light with directional light, low power consumption, good drive performance, fast response, high seismic ability, long service life, green environmental protection advantages of gradually into people's horizons, 0-10V LED high bay light illumination energy conservation has become a traditional large industrial workshop lighting area of the best choice.


The characteristics of the 0-10V LED high bay light:

1. 0-10V LED high bay light light body use the high strength die-casting aluminum, the surface anti-aging electrostatic workmanship of spraying plastics processing, consecrated themselves, corrosion resistance is strong.

2. Humanized structure design, installation and maintenance of lamps and lanterns more easily, suitable for various applications needs.

3. Excellent decorative effect, the use of special surface treatment, color optional appearance, simple installation, convenient disassembly, wide application scope.

4. The lamps and lanterns design fully cooling, surface cover temperature is low, safety, good protective.

5. Using constant current constant voltage control of MV power, wide applicable voltage (AC 90 ~ 264 v / 90 ~ 305 v), and overcomes the shortcomings, such as power grid because of the ballast and noise pollution.

6. 0-10V LED high bay light high stability, long service life as high as 25000 to 50000 hours, more than 10 times longer than traditional light source, low investment and high returns.

7. Good color rendering, light stability, in present of real color more vivid, LED light source color temperature has three , can meet the needs of different environments.

8. Green pollution-free, cold light design, no radiation, to eyes and skin without any damage.Do not contain lead, mercury and other pollution elements, realize the true sense of the green.


For the characteristics of the 0-10V LED high bay light share for you here, today TEK use fin chip the whole structure more cooling technology and SMD light source, implements the light transmission loss, really high photosynthetic efficiency, energy conservation and environmental protection.In addition to energy conservation and environmental protection, 0-10V LED high bay light has long life, fast response time, color pure, concentrated light, etc.

How to improve the life of UFO LED high bay light?

We as consumers want to buy something can use more long, the UFO LED high bay light is no exception.So how to improve the life of the UFO LED high bay light? First of all, to strictly control the quality of UFO LED high bay light encapsulation materials, such as conductive adhesive, silica gel, phosphor, epoxy, solid crystal material, base, etc.Secondly, the rational design of UFO LED high bay light encapsulation structure, such as unreasonable encapsulation yield stress, fracture, etc.Then, to improve the UFO LED high bay light technology, such as curing temperature, bonding, sealing glue, and time will be in strict accordance with the requirement.

Increasing the drive power of UFO LED high bay light life, need to choose high quality, long life of the capacitor is an effective way to improve life drive power;Reduce through the capacitance of ripple current and working voltage;Improve the efficiency of the power drive, lower thermal resistance of components; Protective measures such as good waterproof processing, at the same time should pay attention to the choice of thermal conductive adhesive.

The stand or fall of thermal design is one of the key factors of UFO LED high bay light life. With a chip of the same quality in the different design of lamps and lanterns, the difference in life, even can reach dozens of times, so, a kind of lamps and lanterns design success or failure, the cooling system plays a decisive role.

heat dissipation generally include cooling system level heat dissipation and encapsulation level, to reduce the thermal resistance of lamps and lanterns must consider these two kinds of heat at the same time, the heat level packaging is in LED light source in the process of production of packaging materials, packaging structure and the design of the technological level so as to achieve the aim of heat dissipation.

In terms of packaging thermal design, the main existing silicon-based flip chip structure, metal cooling circuit board structure, a solid crystal material, epoxy resin material such as heat dissipation.Slopes cooling system is mainly based on the research of the related technologies, thus for innovation and improvement of radiator, and with the popularity of high power LED, power is becoming more and more big, at present, the system level heat mainly include thermoelectric refrigeration cooling, heat pipe cooling and air cooling methods of forced heat dissipation structure.Good heat dissipation problem is an effective way to increase the UFO LED high bay light life, so you need to further research and innovation.

What methods of consumers in the choose UFO LED high bay light?

In the past, people use traditional industrial lamp, it often use 250 w, 400 w metal halide lamp, but its light loss is big, caused a huge waste of energy.Therefore, new UFO LED high bay light gradually replaced the traditional mining lamp, in order to energy conservation and environmental protection, long service life, good color rendering, etc advantages, has become the best choice for factories, mines and other production areas.So what methods of consumers in the choose UFO LED high bay light?
 
1. The comprehensive cost-effective 
UFO LED high bay light, especially has passed the certification of explosion-proof certification, military industry, such as quality system certification of the UFO LED high bay lights, because will strictly enforce national standards in respect of production and material selection, don't use inferior corners means to reduce the product cost, so the price may be higher than general lamps and lanterns.But, when buying a put is of high quality products, not only save the cost of electricity, when using more save the cost of the second purchase, maintenance and replacement of lamps and lanterns, the key is to provide reliable guarantee for safe production of our.
 
  
2. The actual demand
 Like coal, oil, chemical and other industries to choose industrial lamp lighting needs not only to consider when can meet the requirements, and other factors, such as dustproof, waterproof, and even to consider explosion-proof requirements.This has restricted the we choose LED lamps and lanterns is the first large elements, bought the general industrial light , can not meet the requirements in terms of energy saving, light lamp cheap expensive;Choose ordinary LED lamps and lanterns can price can accept, but didn't guarantee safety, often replacement of lamps and lanterns, can bring a lot to our work is not convenient, general plant height is high, need to use professional escalator or lift car replacement lamps and lanterns, which increased the our contact input costs.So these companies need to consider the product of choice lamps and lanterns is in conformity with national quality standards, whether through the explosion-proof certification, etc.
 
3. The suitable power, illumination and color temperature
 This is particularly professional, UFO LED high bay light power to choose according to the actual lighting area, high power will cause the electricity waste of resources, low power and can not meet the lighting requirements, UFO LED high bay light products according to your actual demand to you choose the most appropriate answer;In addition the condition such as the intensity of illumination and color temperature of lamps and lanterns is very important also, production line for high resolution, as the textile industry requires high resolution lamps and lanterns.
 
TEK UFO LED high bay light use fin chip the whole structure more cooling technology and EMC SMD light source material, implements the light transmission loss, the really high photosynthetic efficiency, energy conservation and environmental protection.In addition to energy conservation and environmental protection, add bright LED lighting industrial and mining lamp has long life, fast response time, color pure, concentrated light, etc.To provide clients with high quality, high performance UFO LED high bay light lighting products and achieve higher photosynthetic efficiency series solutions, TEK UFO LED high bay light are also acclaimed in the industry.

Why the LED high bay light especially easily broken in the summer?

If you have carefully noticed LED high bay light using process is easy to find the damage rate is the highest in summer, a lot higher than in winter.Why is this? Does the service life of LED high bay light  has relations with season? Or other reasons?

LED high bay light damage rate of the highest in summer, there is only one answer, that is the heat dissipation function of lamps and lanterns is not good, and the temperature of summer is the highest of all the year round, LED high bay light will emit heat in the process of using, if not release this heat, combined with the heat of the summer, LED high bay light easy to burn out.Improve LED high bay light cooling device can't wait, is also a further promotion of power LED high bay light.

What causes the LED heat dissipation system does not pass?

The thermal conductive materials of lamps and lanterns is not enough, such as existing inferior LED high bay light radiator with bad materials, light fever heat conductivity too low.

The thermal design of lamps and lanterns is not reasonable, a lot of lamps and lanterns, no heat dissipation design take parts assembled directly, without scientific experiment testing.

The installation environment is unreasonable, LED high bay light installation requires a certain heat dissipation space for heat dissipation, and the installation environment humidity, LED high bay light on the damp environment, also easy to bad, because the LED high bay light are electronic components, once wet lead to easy bad impact performance.This kind of reason, only the users themselves to use the note.

How to judge the merits of the LED high bay light source ?

As an industrial powerhouse in China, in the energy consumption of the factory, lighting energy consumption occupies a certain weight. Therefore, LED high bay light using new LED light source as light-emitting materials, which can achieve the effect of energy conservation and environmental protection, become the focus of people attention. So what factors influence the quality of LED high bay light source?  how to judge the merits of the LED high bay light source ?

1. According to the semiconductor light-emitting diodes electric property from the LED high bay light source electrical to consideration
LED electrical characteristics of PN junction is a one-way nonlinear electrical conductivity, low voltage driver, and sensitive to static electricity, etc.The electrical characteristics is different with traditional light source, so the main measurement parameters include positive drive current, the forward voltage drop and reverse leakage current, reverse breakdown voltage and electrostatic sensitivity, etc.

2.According to the PN junction temperature of LED high bay light from the heat dissipation performance to consideration
The LED high bay light get higher power and luminous efficiency, solve PN junction temperature and heat dissipation problem is particularly important.Judge LED high bay light, general with thermal resistance, thermal performance parameters such as temperature, junction temperature said.

3. The life span and working reliability of LED high bay light

We evaluate the lifespan of LED high bay light does not mean that the cycle available from used to damage, and it is under the condition of rated power, luminous flux attenuation to the initial value of the specified percentage when the last time.The longer, the LED high bay light the longer lifespan.

4. In view of the LED light source of biological or body radiation safety into consideration
Due to the LED high bay light source is a narrow beam of light, high brightness light-emitting elements, the radiation may cause damage to the retina, so, the international electrotechnical commission IEC for application of LED light source used for different occasions. Specifies its effective radiation limit requirements and test methods, which is judge LED high bay light quality of an important factor. Among them, the European Union and the United States do mandatory to perform LED radiation safety testing .

Judgment of LED light source quality mainly is decided by these factors, in the future, LED lighting industry will become more competitive, which means opportunity and challenge coexist.

Why the LED high bay light especially easily broken in the summer?

Click here to edit text.

The development of LED street lights in 2017

LED street light all the environment stable, but because of many objective factors influence, LED street lamp driving speed significantly lower than expected this year, growth is slowing, market is more rational.


LED street lamp no matter in the entire road illumination, the evenness and glare control has a great progress, but because the market need to tighten and LED street lamp factory base huge cause market competition is intense, the LED street lamp order more focused on the larger companies. Future LED street lamp manufacturers in addition to spell quality,also need to spell quotation, seek new economic increase point also is principle of LED street lamp manufacturers.


LED street lamp structure planning changes, light modularization become a new trend in the future.Before all and modularization programming must be the whole lamp replacement once the lamps and lanterns of the problems, we will only replace electronic control parts after modular , although, from the perspective of a single lamp and failed to save money, but in the long term capital is lower.


The intelligent control system in the use of LED street lamps gradually increase.Domestic and foreign many LED street lamp company beginning committed to develop intelligent LED street lamp produces .Intelligent LED street lamp can energy saving 10% -20% again on originally street light , but the stability of the intelligent LED street lamp system deficiency, failure rate than the original doubled, maybe bad much faster than light control system.

How to choose household LED corn light ?

At present, a lot of people using home LED corn light, these products has provided people with high efficiency and energy saving of lighting, reduced the family electricity costs, won the favour of people, because a lot of friends is not very understanding of LED industry, easy to be misled by the businessman when buy lamps and lanterns so that buy a poor quality of the products.So, how to choose household LED corn light?
 
LED corn light enterprise in the market now is numerous, quality and performance difference is very big.In general, people see the lamps and lanterns of roughly is aluminum.Inferior LED corn light there is a bad heat dissipation problem, because all the heat sealed inside the lamps and lanterns, could not spread out, to a large extent influence the service life of the lamps and lanterns;And aluminium LED corn light is better, it improves the cooling speed 3 times.
 
In the power supply block, common are built-in.Built-in the biggest advantage is that you can directly replace the existing fluorescent lamp;The current many places a greater demand for LED corn light, a room there are a lot of light, then use the built-in power is good, can save a lot of manual labor and material. As for the lamp holder, can be set according to the original lamps and lanterns.
 
Chip is basically a penny a points goods, famous brand better than the second line brands, the same brand of chips, different packaging manufacturers, their quality is different also. When choose LED corn light can carefully ask merchants, in general, international companies on the chip quality has guaranteed, and stable performance in using LED corn light.
 
TEK lighting LED corn light has a strong technology research and development strength, market reputation, product use the high performance LED light source and high light transmittance optical mask, maximum close to traditional fluorescent lamp appearance, light soft, comfortable, no stroboscopic, reduce visual fatigue, is the ideal home LED corn light.

LED street light market development should be standardized

With the development of LED lighting technology, people have realized the advantage of LED light source, and apply it to daily lighting, in some way, also can see the LED street lamp, but on the whole, the social permeability of LED lighting is not high, market development is relatively extensive, LED street lamp need a unified standard to guide the market forward.


From the current market situation of LED street lights, the most serious problem are standardized question and product homogeneity, LED street lamp manufacturers now a lot, and the module of each manufacturer is not unified, each link is not unobstructed, such as spare parts don't have universality, once out of the question, also need to contact the original factory to maintenance, virtually increased customer usage costs.


After years of development, LED lighting industry in China has made great progress, LED enterprises are numerous, but the small scale of enterprises, lack of leading enterprises, a lot of LED street lamp capacity at a low level, homogeneous market competition is fierce, basic copy imitate each other's stage, is often a design for the new, other home immediately follow suit, imitation in succession, with the price war disrupted the market order.


LED street light hasn’t unified standard of quality supervision, 70% of which focuses on the integrated application of downstream link, the lack of upstream of the core technology, product quality is uneven, many manufacturers there is blundering psychology, not heavy to do product, manufacturing lamps with low-end material, the result cans be imagined, that don't trust of the customers.


TEK lighting domestic well-known manufacturer of LED street lamp design, has a wealth of technical experience in the field of road lighting project to undertake a number of street lamps, relying on excellent product quality, won the customer high praise.

Technical communication: the market sell like hot cakes product characteristics of LED corn bulb

LED corn bulb is a new kind of energy saving lamps and lanterns, it is more efficient than traditional incandescent lamp, more efficient, more stable.At present, the global energy supply tension, improve resource utilization, greatly reduce the energy consumption has been the consensus of the governments, LED light source as a green energy-saving environmental protection lighting, more competitive advantage than traditional lighting products, is people to become "the fourth generation of lighting source.


Convenience is a significant characteristics of LED corn bulb, LED lighting products had entered innumerable families, but because the incandescent lamp and electronic energy-saving lamps in People's Daily use still occupies a very high proportion of the future better promotion products, many manufacturers in product design more joint incandescent bulbs, has a strong generality, existing way of interface can be used, people use more convenient.


Compared with the traditional incandescent lamp or energy-saving lamps, LED corn bulb is more safe.General energy-saving lamps work when the temperature will be around 70 ℃, ordinary incandescent light bulb temperatures of up to 90 ℃, if somewhat accidentally touch, can cause scald. And LED corn bulb temperature is lower, around 40 ℃, the ball bubble lights inside and heat dissipation design, burns will not happen.
 

LED corn bulb life is longer, several times that of ordinary light bulb, the life of ordinary light bulbs in 1000 hours, energy-saving lamp life in 8000 hours, soon will appear problem.And the sell like hot cakes on the market of LED corn bulb service life can reach more than 50000 hours, you can use for a long time, but also save the electricity.


TEK Lighting is a leading manufacturer of LED lighting product design, in the field of LED lighting technology has a strong strength, product development breakthrough of 100 W incandescent technical difficulties, luminous power products is only 10 W, and the light efficiency is very high, 160 lm/W, greatly improve the utilization efficiency of electricity, with smaller power hair more bright lights.

Why LED high bay light is more and more dark?

It has been found that just buy back when the light is very bright, but use a long time, brightness slowly become low.
 
The feature of LED is long life, theory life can reach 8 to 100000 hours, of course, some people are skeptical that LED really can achieve such a long life, calculate according to the life of the LED , does LED high bay light can really use to decades not bad?
 
Currently on the market some products use LED characteristics, declared himself LED high bay light to zero droop, the actual rate of bad light is quite high.With a little attention where has been installed LED high bay light, it is not difficult to find a lot of problems.Just change the LED light source, lighting effect is very obvious, but after a period of validation, the light failure is very serious.Isn't this, specific questions?
 
So ,what is light failure ?
 
Droop refers to the light over a period of using, luminous efficiency is decline, brightness there isn’t high like initially.
 
The cause of LED high bay light produce failure
 
Using the LED chip quality is bad, brightness decay rapidly.

 
The deficiency in the production process, the cooling performance is bad.The LED working temperature is lower, the smaller the droop.

LED street lights gradually replace the traditional street lamp will no longer be far away 

The lack of brightness of traditional street lamps is not an individual phenomenon, and many of the paths used in traditional street lamps are inadequately illuminated and dimly lit. The reason is that because traditional street lamps have been used for long periods of time, they can be oxidized and formed a thick layer of black dust on the surface, which makes them less bright.Streetlamps are created to facilitate the travel of drivers and pedestrians, which can cause blurred vision and create a safety hazard for travelers.

At present our country highway, road lighting widely used in most of the high pressure sodium lamp and low pressure sodium lamp, although they has the advantages of low cost, strong ability to penetrate the fog, but the start time, power consumption, life is not long, color rendering index is low, the object under the environment of this kind of light color distortion is serious, and plenty of waste but also cause serious light pollution, the defects cannot be ignored.

LED street light not only have more advantages than traditional sodium lamps, they also make up for the shortcomings of traditional street lamps.LED street lights can jump-start, lamps and lanterns with high efficiency, less consumption and energy saving rate is high, stable performance, long life, high color rendering index, and easy to control Especially to remote control the light source, and can adjusted according to the crowds, traffic and the actual situation such as the weather changes, can effectively promote the overall energy-saving lighting system, space, and many other advantages.

In 2016, all countries in the world are making efforts to promote energy conservation and environmental protection and implement a comprehensive ban on incandescent light bulbs, which will give the LED street lighting industry a lot of room for development.

TEK specializes in the development of LED lighting products and has accumulated rich experience and technology in LED outdoor lighting.Its product has innovation unique structure design, enjoy "convection type LED lighting" patents, such as the production of LED street lights products possess high photosynthetic efficiency, low energy consumption, high color rendering, no stroboscopic, road illumination uniformity and flare and long life and other advantages.

At present, there are many cities in our country which have been replaced by LED street light, which can be seen in the light of the government's emphasis on LED lighting and the prospect of LED lighting.LED lighting is known as the fourth generation of light.As LED technology matures, the continuous decline in production costs, and constantly improve their awareness of LED lighting products, LED street lights gradually replace the traditional street lamp will no longer be far away.

In the future, LED high bay light market share will be increase four times than 2016

The market for LED high bay light in the next few years is huge, and the market  share for LED high bay light is expected to be more than four times.

Nowadays, emerging industries and high-tech base around the country, the number of development zone and covers an area of growing, according to relevant data statistics, as early as 2015 domestic new factory warehouse area has reached more than 500 million square meters.This made LED high bay light to rapid growth in the LED industry.

China produces most of the LED high bay light exported to Europe, until now production has reached the peak, in the past two years layout of industrial and mining lamp market also is in a high-speed growth, is expected soon there will be a price war on the fight, the market appeared chaos.

If you can't make first brand in the market, create a new niche market first.Focusing on the development and sales of LED high bay light, TEK hopes to build its own competitive edge in the LED market.No matter how competitive the market is, TEK always insists on don't drop the quality, and only make suitable for myself and high quality requirements.

Indeed, industrial lighting product installation and maintenance cost is very high, the high demand for product quality and after-sales service, low quality products at low prices at the same time, it is easy to appear due to the high maintenance cost of product damage and appear, so the price will not be a priority for the customer to choose.

In the current market application situation, LED high bay light product is very mature, the technology is no longer a problem, it is worth paying attention to the question of unit price. TEK shows that it will compete rationally, not with price-to-price ratios.

Nowadays LED indoor lighting is already present in mass prices hit bottom, and industrial and mining lamp market as the current circumstances of propellant, or will be in the market of stimuli into the next explosive growth, many LED high bay light manufacturers also will continue to focus on the LED high bay light market development trend.

The price of LED high bay lights will not change much in the last two years

In the outdoor industry lamp market, the golden halogen lamp has always been the mainstream of the market because of the advantages of custom habit and product price.But because of its short service life, high maintenance costs and also has too much power, low brightness, pollution, these disadvantages make market space gradually eroded by LED high bay light.

Market demand is also driving a large number of companies. TEK has introduced a number of high-cost LED high bay lights.It is understood that LED high bay lights from Bridgelux and Cree brand, the driver power comes from Taiwan Meanwell and Philips, guarantee 100% of the aquatic product inspection, quality assurance for 5 years, mainly used in warehouses, factories, conference hall, gymnasium, stadium, gas stations and other places.

TEK lighting aspires to be "LED high bay light professional brand", therefore, TEK lighting overall positioning in the development and application of all kinds of high bay lamp, including UFO LED high bay light, IP54 LED high bay light, etc.It also focuses on the development of the intelligent chemical lamp, the DALI dimming control system and so on.

The TEK LED high bay light has the advantages of the design of heat dissipation structure compared with the same kind of LED high bay light, and the effective cooling area is large and the price ratio is high.LED high bay light are 5-6 times brighter than traditional lamps and 10-15 times longer than traditional lamps. Although these TEK products are not the cheapest in the market, they are the most cost-effective.

With the decrease of the supply chain production cost, application link with the decrease in price, in recent years, China LED indoor lighting product prices fell more than 20% per year.Large power industrial lighting products, represented by LED high bay light also declined in varying degrees.

TEK LED high bay light price reduction also is very big, for example, 100W LED high bay light, the same category products in the market at present is the selling price is as low as $89 or less, per watt price has dropped to less than 5 $. At the same time, people in the industry say that LED lighting has bottomed out because of the cost of supply chains, and there is limited room for price cuts.

Indoor lighting products are already in a vicious competition for price, but there is a fundamental difference between LED high bay light and the indoor low-power lighting products.LED indoor lighting may have achieved a high price hit, but LED high bay lights are unlikely to change much in the last two years.

TEK Lighting tell you why LED corn light is popular with people

With the rapid development of LED technology, it has become a trend for LED corn light to replace incandescent bulbs.In our lives, people have become more and more aware of it, and the LED corn lamps are becoming more and more popular. What makes LED corn lights so popular with consumers?

LED corn lights are welcome and need to start with the advantages of LED corn lights:

LED corn lights are very efficient and efficient.As is known to all, because LED light source has the effect of energy saving, so the LED corn light more energy-saving than ordinary incandescent lamp, can also help you save a lot of electricity.In addition to the advantages of high efficiency and energy saving, its colour and lustre is pure, soft and warm, not miserably miscellaneous any light, and color also is extremely diverse, conform to the requirements of various kinds of decoration style.

LED corn lamps are powered by low voltage.In physics, is safer than high voltage power supply, in the process of using single bulb of voltage is between 2 v to 4 v, the voltage is low, so can be more secure for everyone to use, don't worry about the power of the lamps and lanterns will bring harm.

LED corn light qualitative comparison is hard, USES the light source is in the form of solid, so at the time of earthquake, LED corn light won't appear stroboscopic phenomenon, it is because of the particularity of this, to make the LED corn lamp stand out in the other lamps and lanterns, occupied most of the market of lamps and lanterns, to win consumer's eyes.

LED corn lamp's light is soft and not dazzling, in the light of lights also contains no radiation, no ultraviolet and infrared light, and the ordinary incandescent lamp is ultraviolet and infrared, the permanent will make the eye fatigue, brings to the body health.

That's the benefit of the LED corn lights.

Do you know the past and the future of LED street lights ?

LED street light currently exist in the United States, Europe and China.Among them, the characteristics of Chinese LED street light are characterized by modular structure, high protective properties of modules, and high protective water-resistant joint modules and actuators.And the European LED street lamp features a full-plate version, a shiny glass with steel, and little or no heat sink on the back.The characteristics of American LED street lamps are in the form of the majority and the compass.

Due to have respiratory effects in the outdoor LED street light, breathing effect cause gas exchange occurs in the wall, make the external toxic or harmful gases into the lamp cavity corrosion unprotected lamp bead and aluminum plate, causing death lamp.In order to solve this problem, there are many innovative designs in China.For example, the application of rubber and water on PCB boards is used to solve the corrosion failure of the bulb and PCB.

Modularization scheme is Chinese innovation, as early as the beginning of 2009 , the first to put forward the concept of modular LED street light, through the standardization of the LED module can solve the heat dissipation, waterproof, light distribution, maintainability, versatility, and many other problems in the field of high power LED lighting.The future of the LED industry requires a new business model to address industry pain points. LED street light the more intensive, the lower the cost;The higher the intensification, the more advanced the technology.

At this stage, the overall lamp market competition is more and more fierce, the product price declines continuously increased, but the cost of power supply in the proportion of the whole lamp cost has been high, resulting in profit space gradually compressed.The cost of the whole lamp is 39 percent, the cost of the lamp is 26 percent, the cost of the kit is 29 percent, and the cost of the accessories is 6 percent.

100 w LED street light, for example, the whole lamp price from $1.10/W in 2014  fell to 0.70 in 2016 $/ W, drop to 34%, but the price of the power supply remains at $19.85 in 2016, only 28% decline.

In the high-end power cost, from the cost of raw materials is as high as 60%, when prices unchanged, an integrated circuit can accommodate the number of components every 18 to 24 months will be doubled, the performance will be doubled.

In terms of managing costs, the future industry tends to be more concentrated and the market is more affordable and efficient.In terms of the cost of selling, the market concentration and the brand effect are continuously promoted.In terms of the cost of workers, the scale of the future of a single LED street light product has led to automation of production.All of these can effectively control and reduce costs.

TEK lighting: how can I improve the life of IP54 LED high bay light?

Each IP54 LED high bay light, consumers hope that the service life of lamps and lanterns as long as possible, but due to some technical reasons, the service life of the IP54 LED high bay light will be affected, damage in advance, there is no ideal for 100000 hours.So, how do we, as IP54 LED high bay lighting manufacturer, to ensure that the use of the lamp is idealized? How to increase the service life of lamps and lanterns?

First, the quality of the packaging materials that the manufacturer should guarantee.Second, the design of the packaging structure of multi-lamps should be reasonable, and the data design should be strictly installed.Finally, we need to solve the heat dissipation problem of IP54 LED high bay light, which is the most important link.If the heat dissipation problem is not solved, the result is a cloud.

Heat dissipation of IP54 LED high bay light can be summarized as two parts: the system level heat dissipation and encapsulation level cooling, in order to increase the service life of lamps and lanterns, these two kinds of heat dissipation problems must to be solved.

System level heat dissipation is mainly based on the research of the related technologies, thus for innovation and improvement of radiator, and with the popularity of high power IP54 LED high bay light, power is becoming more and more big, at present, the system level heat mainly include thermoelectric refrigeration cooling, heat pipe cooling and air cooling methods of forced heat dissipation structure.

The encapsulation level heat is the purpose of heat dissipation through the design of the packaging material, packaging structure and process level in the production of LED light source.

In terms of packaging thermal design, the main existing silicon-based flip chip structure, metal cooling circuit board structure, a solid crystal material, epoxy resin material to heat dissipation.

It is the key to increase the service life of IP54 LED high bay light and guarantee the quality of material.The service life of lamps and lanterns can be guaranteed as long as the heat dissipation function of lamps and lanterns is designed.

How to select the suitable LED corn light manufacturer?

How to select LED corn light manufacturer?As leds are widely used, leds are springing up all over the place.But because of the money, the strength of the manufacturer is very different, so that their LED corn light produces quality is also very uneven. So how to choose the manufacturer, become the consumer's problem.

As we all know, the high quality product quality, its origin must come from the capital strength of the manufacturers, because only the abundant funds, in order to win the market, will use the latest production technology, will pursue the brand effect of the market, attaches great importance to the use effect of the consumer, want to win the trust of consumers.So the quality of the product must pass, must be guaranteed, otherwise the long-term development of the LED corn light manufacturer is unfavorable.So the premise that selects a LED corn light manufacturer is that have the manufacturer of strong strength.

First of all, we can choose the manufacturer which is strong, and we can confirm the choice by the manufacturer's reaction in the market.What about the company's reputation?What about the credibility among consumers?What about the after-sales service?These all reflect the quality of the LED corn light products that the manufacturer has.We can choose a few manufacturers that have a good reputation, and then check the product details.

After all hearsay rather than to the field to see, to determine the brand on the market a good manufacturer, you can come to view the specific to the manufacturer of the product quality.Can go from the material of lamps and lanterns, the technology of lamps and lanterns, the certificate of qualification of lamps and lanterns to wait to see.It's best to try and run for a while, and then see how the lights do.The heat dissipation function is developed, the quality of the product is not poor basically, can guarantee the service life of LED corn light basically.

According to the above statement to choose the manufacturer of lamps and lanterns, basically can choose quality is good quality and appropriate LED corn light.

What is the light source of LED corn bulbs is healthiest ?

At present, a lot of LED corn bulbs used in shopping malls, household, office and other indoor lighting, but people do not know specific choose what light source of LED corn bulbs, how is it quality, if did harm to health are unclear. So, what is the light source of LED corn bulbs is healthiest ?

We usually use natural light is the sun, the sun can be divided into three parts, one is ultraviolet (uv), from 250 to 400 nm wavelength, two is to visible light, glittering in the 400-750 nm, three is near infrared, between 750 and 2500 nm wavelength.With ultraviolet (uv) and near-infrared produce bad effect to the skin, such as can make the skin to blacken, cause skin irritation, the phenomenon such as aging, rough, but the amount of ultraviolet ray also can bring certain benefits, such as promoting calcium-phosphorus metabolism and bone growth and development, etc.And the visible part, it is our human eye can see light, the blue light has the highest energy of the photons in the visible light, the eyes of retinal damage to a certain extent, but low radiation blue light have a good side, such as can whiten skin and teeth, can treat disease of infant jaundice, also can control people's clock, etc.

Into the era of LED lighting, blu-ray harm is often mentioned, because blue hazards in lighting without awareness, only in the use of scientific methods to guarantee security. LED lighting does not necessarily have blue light damage, it is determined by the amount of radiation and radiation time of the blue light.The radiation safety of LED lighting is higher than that of fluorescent tube, energy-saving lamp and gold halogen lamp under the same indoor illumination and color temperature.Different LED corn bulbs are made by different factory, and  good quality LED corn bulbs blu-ray  radiation is low.

Generally speaking, the greater the power of the LED corn bulb of blue light, the greater the damage, such as more than 20W LED light source, in use must pay attention to the installation height, the higher the height, the smaller the harm of blue light.In addition, the amount of blue light radiation decreases with the decrease of color temperature, while the small power LED light from 3500K to 2800K is basically in line with national standards.

But the current domestic many LED corn bulbs light source are mostly high color temperature , such as many LED to absorb dome light with more than 6500 k color temperature, while the LED corn bulbd for bedroom illume, this will cause a large blue light radiation, therefore, has the old man and the child's home in the home, should be considered.

TEK Lighting suggestion: commercial lighting, proposal use LED white light color temperature below 6000 k, highest do not exceed 6500 k. Office lighting, suggests to use 5000 k to 3200 k color temperature. Family lighting recommended power less than 8W LED corn bulbs , color temperature below 3500 k, it will be good for the health of the body.

Innovative technology makes UFO LED high bay light more cheaper and energy-saving

In the numerous lighting products, energy-saving lamps as is known to all and needless to say, at the same time, UFO LED high bay light also great leap into the people’s life, as a new generation of lighting source, UFO LED high bay lights have remarkable characteristic, such as high efficiency, energy saving, environmental protection, is considered to be a revolution in the new era of lighting industry.

After more than ten years development, technology development to mature, it has "tall", from the initial flying manufacturers gradually, increasing its quality performance, product price is more and more cheaper, market penetration are also gradually increase, as Metal halide lamp is exit market, high pressure sodium lamp share compression, UFO LED high bay light era has come, will become the main industrial lighting products.

Solved the main block that influence UFO LED high bay light performance, TEK lighting products in service life, lumen value, light failure, safety, reliability, in such aspects have greatly improved compared with other LED lighting products. Not only that, TEK UFO LED high bay light is also highly competitive with its domestic and international same product in price.

At present, UFO LED high bay light products due to the design is complex structure and high cost, its price still can't compared with the ordinary energy-saving lamps, and factors become obstacles to UFO LED high bay light popularization and become a major stumbling block.While TEK Lighting product fundamentally solves the bottleneck, boost UFO LED high bay light went out of the "save electricity don't save money" circle, offers into a double guarantee of quality and price.

The market for the UFO LED high bay light is not fully mature yet, but the market is already in front of people, and LED lighting has become a trend.The market to really open, need to enterprise starting from the market, introduce more products that meet the needs of market development, from the quality, technology and cost, in order to realize the real popularity of UFO LED high bay light.

Nowadays, TEK lighting has formed a two-wheel drive technology and price, with its own technology advantages and innovative research and development strength, in order to promote the popularization process of UFO LED high bay light products to strive.

Why UFO LED high bay light become the most popular by factory ? here is the answer

A lot of people have a question about the application of UFO LED high bay light, which is why many manufacturers are willing to choose UFO LED high bay light, for example, in factory lighting.the reason of UFO LED high bay light become the most popular by factory .

It is well known that lighting consumes a large proportion of the energy consumed in the factory.So when choosing factory illume lamps and lanterns, how to realize efficient energy conservation, environmental protection is we think that is pay attention to when designing UFO LED high bay light. Adopting the new LED light source on the UFO LED high bay light, besides energy-saving and environmental protection, it also has the advantages of long life, quick response time and pure light color concentration.There are advantages to using UFO LED high bay light:

1, UFO LED high bay light are used to apply new technologies, new materials and new processes to high-power production applications.

2, compared with high pressure sodium lamp or metal halide lamp, though UFO LED high bay light has higher initial cost, but due to the LED light source with high photosynthetic efficiency, wide range, strong directivity characteristics, can achieve the effect of long life, high energy saving.

3,Green environment: no stun, low glare.UFO LED high bay light is made from a silicon wafer that does not contain any toxic chemicals, and is a truly pollution-free source of green light compared to the energy-saving lamps.

4, good color rendering, color rendering index greater than 80, infinite close to natural light, lighting, comfortable, and can be made into color bulb, needed to use the environment can realize all kinds of different light illumination

5,Instant start: start time is less than 0.1 seconds, instantly start lighting

6,The UFO LED high bay light has beautiful appearance, stable structure and perfect perfection.

How to solve the question about UFO LED high bay light in summer?

How to solve the question about UFO LED high bay light in summer?

During this time of year, it is the most challenging for UFO LED high bay light. Wet and hot weather makes moisture-proof and heat dissipating of UFO LED high bay light are quite paradoxical, this is a head-on collision of natural contradictions.

How to do the moisture-proof work in the rainy weather, and maintain good heat dissipation in the high temperature environment, became a difficult problem for the UFO LED high bay light.

Moisture-proof and heat dissipation, a pair of natural contradictions

UFO LED high bay light inside device belongs to the MSD components (moisture sensitive device), once there is moisture to enter may cause light bead, PCB board, power supply, power supply cord device oxidation corrosion and resulting death lamp.Therefore, the module, internal structure and exterior lighting of UFO LED high bay light is required to be well designed and waterproof.

At the same time, the internal components of UFO LED high bay light is also the most heated electronic components, such as LED lamp beads, drive, switch power supply, etc.Bad heat dissipation design can oxidize the lamp materials and affect the quality and life.If the heat is agglomerated and dispersed, it can lead to overheating of the LED internal devices and failure. Therefore, good heat dissipation requires a thorough and convective structure, which contradicts the demand for moisture protection.

How to solve the problem？

In the heat and humidity of the weather, facing moisture and heat, this seemingly irreconcilable contradiction can be deftly resolved through exquisite hardware and elaborate structural design.

First, reducing power consumption and reducing thermal damage is an effective way to improve heat dissipation.Represented by TEK lighting famous LED enterprises, from the source to choose high quality LED chip to optimize design, pay attention to the independent development, efficient, high quality driven power supply superior raw material quality and excellent performance parameters for heat, moisture laid a firm foundation.

Furthermore, the improvement of module production technology is also the most important.It is understood that TEK lighting for PCB electronic structure optimization, change numerous for brief, reasonable arrangement, and make use of the high thermal conductivity material glue sealing, at the same time meet the demand of seamless accessible and components of the cooling water vapor.

Finally, rational optimization of the light structure can play a key role.In material on considering heat and oxidation resistance of lamps and lanterns select high-quality aluminum, using multilayer space inside UFO LED high bay light architecture, form the natural convection heat dissipation structure, can make full use of the natural air convection, both cooling and sealing, both also improves the reliability and service life.

Even in the face of such a severe climate test, TEK UFO LED high bay light can still maintain efficient heat dissipation on a reliable moisture-proof basis, and the lamps operate as new and show the quality to the outside world.

Improve LED corn light innovation ability is a manufacturer essential quality

LED corn light industry while developing rapidly in our country, form a larger industry scale, and still has a huge market potential, however, lack of core and key technologies is our short board and the industrial organization pattern of scattered, small, still restrict improvement of China's LED industry international competitiveness.Technological innovation is an important approach and foundation for the development of LED industry, and it is an important breakthrough for enterprises to win future business opportunities.In some ways, competition in the future is largely a matter of technology.

The current situation of LED corn light

In recent years, domestic LED corn light have been dazzled by new stars and capital flows into the blue sea, which has turned into a situation of overcapacity.At present, the homogenization of market competition is particularly serious, and the market competition on the basis of commodity homogeneity is called "homogeneity competition".

In the homogeneous environment of the diversified selection of LED corn light products, enterprises are most likely to have a "Recklessly" situation in the face of competition, which leads to vicious competition. Copying imitating popular industry, product homogeneity serious, lead to enterprise is keen to compete on price, plus market gradually saturated, reduced demand, so that the excess production capacity.

The future of LED corn light

Under the rapid development of LED corn light enterprises, the homogeneity of products will inevitably lead to the elimination of a large number of enterprises.This phenomenon is both a huge challenge and a rare opportunity for businesses.In the future, people will demand higher and higher requirements for product quality and function, and low price and low quality products will not form unique customers, let alone achieve significant profit.

As the most intuitive embodiment of enterprise value, the sustainable innovation of products is one of the criteria to measure the sustainable strength of enterprises.

How should LED corn lamp enterprises develop?

In recent years, intelligent lighting has been a big game for many capital hunting.With the development of Internet and information technology, the future of lighting must be intelligent interconnection.Introduce the lighting intelligent interconnection concept, not only will affect the household sector in the future, the global intelligent household market will no doubt be affected by the storm, and certainly will will play a positive role to wisdom urban construction.In the homogeneous competition LED industry, intelligent connected lighting will also be a bright outlet for lighting enterprises.

With the mature of LED corn light technology, TEK lighting is to shift from the idea of selling products to sell service, we actively adapt to the development of the new normal lighting industry, constantly adjust development strategy, transformed into a provide high value-added services.

Between the competition between enterprises today, not a product of competition, but competition between business models. In lighting companies are also trying to sell products, TEK lighting to" product as a service "business model is industry a big innovation. In the" product is service "business model, product service is service process, service mode of the construction of the fundamental purpose is to gain a competitive advantage in the fierce competition in the market.

From the point of view of the current competitive environment, the acceleration of the integration of the entire LED industry, industry itself exists because of the many low-end manufacturers, pay attention to price competition and regardless of the quality of the products the unwritten rules of behavior, will lead to a large number of companies disappear, in the process of the development of the industry, this is a very normal thing.And LED corn light enterprise want to stand out in this environment, want to maintain superiority in the competition, improve oneself innovation ability is a essential quality.